IGCSE Physics 0625 notes › Cheat sheet

IGCSE Physics 0625 cheat sheet

BOOKLET given in the examLEARN you must remember it · Each block links to its lesson.

IGCSE Physics 0625

IGCSE PHYSICS 0625 · Extended
pastpaperprep.com/revision-notes

1 Motion, forces and energy

1.1Physical quantities and measurement techniques

Length: use a ruler, start at the zero mark (or subtract the starting reading), and look straight at the mark. Liquid volume: use a measuring cylinder; for water, read the bottom of the meniscus with your eye level with it.LEARN
Volume of an irregular solid that sinks: lower it into water in a measuring cylinder until it is fully under water. Its volume = new reading − starting reading.LEARN
Time: a clock for minutes or hours, a stopwatch for several seconds, a digital timer with light gates for intervals well under a second. Hand timing adds a reaction-time error of roughly 0.2 s0.2\ \text{s}.LEARN
Small distance or short time: measure many together (a stack, or 2020 oscillations) and divide by the number. Repeat and take the mean.LEARN
Period of a pendulum: the time for one complete oscillation, out, across and back to the start. Period = time for nn oscillations ÷ nn.LEARN
Scalars have size only: distance, speed, time, mass, energy, temperature. Vectors have size and direction: force, weight, velocity, acceleration, momentum, electric and gravitational field strength.LEARN
Two forces or two velocities at right angles: resultant =X2+Y2= \sqrt{X^2 + Y^2}, at angle θ\theta to XX where tan⁡θ=YX\tan\theta = \frac{Y}{X}. Or draw them tip to tail to scale and measure. Give the size and the direction.LEARN

1.2Motion

v=stv = \frac{s}{t}LEARN
Speed is the distance travelled per unit time (a scalar). Velocity is speed in a given direction (a vector).LEARN
average speed=total distance travelledtotal time taken\text{average speed} = \frac{\text{total distance travelled}}{\text{total time taken}}LEARN
Distance–time graph: the gradient is the speed. Horizontal line: at rest. Straight sloping line: constant speed. Curve getting steeper: speeding up; curve getting less steep: slowing down.LEARN
Speed–time graph: horizontal line above the time axis: constant speed; line along the time axis: at rest; sloping up: speeding up; sloping down: slowing down. The area under the graph is the distance travelled.LEARN
Near the Earth's surface the acceleration of free fall gg is approximately constant, about 9.8 m/s29.8\ \text{m/s}^2. With no air resistance, every object falls with this acceleration, whatever its mass.LEARN
a=ΔvΔta = \frac{\Delta v}{\Delta t}LEARN
For motion in a straight line, the gradient of a speed–time graph is the acceleration: a straight line means constant acceleration, a curve means changing acceleration. Taking the direction of motion as positive, a deceleration is a negative acceleration.LEARN
Falling from rest through air or a liquid, an object's acceleration decreases as the resistance grows with speed. When the forces on it balance (in air, when the air resistance equals its weight), the resultant force is zero and it falls at a constant terminal velocity.LEARN

1.3Mass and weight

Mass is the quantity of matter in an object, in kg. It changes only if matter is added or removed, so moving or reshaping an object doesn't change it.LEARN
Weight is the pull of gravity on an object's mass. It is a force, so it is measured in newtons (N), not kg.LEARN
g=Wmg = \frac{W}{m}LEARN
Gravitational field strength gg means force per unit mass, in N/kg: the pull of gravity on each kilogram. Near the Earth's surface it is about 9.8 N/kg9.8\ \text{N/kg}, equal to the acceleration of free fall, about 9.8 m/s29.8\ \text{m/s}^2.LEARN
A beam balance has its pivot at the centre, with the pans at equal distances from it. It is level when the weights in its two pans are equal. Both pans have the same gg, so the masses are equal too.LEARN
Weight is the effect of a gravitational field pulling on a mass, W=mgW = mg. Where gg is different (the Moon, another planet, far from the Earth), the weight changes but the mass stays the same.LEARN

1.4Density

ρ=mV\rho = \frac{m}{V}LEARN
Density is mass per unit volume, in g/cm³ (mass in g, volume in cm³) or kg/m³ (mass in kg, volume in m³). 1 g/cm3=1000 kg/m31\ \text{g/cm}^3 = 1000\ \text{kg/m}^3.LEARN
To measure density, find the mass with a balance and the volume, then divide. Liquid: volume in a measuring cylinder, mass = (cylinder + liquid) − empty cylinder. Regular solid: volume from length × width × height. Irregular solid that sinks: volume = rise in water level when it is fully under water (displacement).LEARN
An object floats in a liquid if its density is less than the liquid's density, and sinks if its density is greater. For a hollow object, use its average density.LEARN
Liquids that do not mix form layers in order of density: the least dense on top, the densest at the bottom, whatever their volumes.LEARN

1.5.1Effects of forces

A force can change an object's size and shape, its speed and its direction of motion. Forces are measured in newtons (N).LEARN
Extension = stretched length − original length. A load–extension graph that is a straight line through the origin shows the extension is directly proportional to the load.LEARN
k=Fxk = \frac{F}{x}LEARN
Spring constant kk: force per unit extension, in N/m or N/cm. It holds only up to the limit of proportionality, where the straight part of the load–extension graph ends.LEARN
Resultant of forces along one line: add the forces that point the same way, subtract those that point the opposite way, and give the size and direction.LEARN
Newton's first law: with zero resultant force, an object stays at rest or moves at a constant speed in a straight line. A resultant force changes its speed, its direction, or both.LEARN
Friction acts between surfaces that touch: it can oppose motion, and it heats surfaces that rub. Drag is friction in a liquid or gas (air resistance in air): it opposes the motion and grows with speed.LEARN
F=maF = maLEARN
In F=maF = ma, FF is the resultant force, and the acceleration is in the same direction as the resultant force.LEARN
Circular motion at constant speed needs a resultant force towards the centre, perpendicular to the motion. The force must be larger for a higher speed (same mass and radius) or a larger mass (same speed and radius). A larger force gives a smaller radius (same mass and speed).LEARN

1.5.2Turning effect of forces

Moment: the turning effect of a force about a pivot, in N m (or N cm when distances are in cm).LEARN
moment=force×perpendicular distance from the pivot\text{moment} = \text{force} \times \text{perpendicular distance from the pivot}LEARN
Principle of moments: when an object is in equilibrium, the clockwise moments about any point add up to the same total as the anticlockwise moments about that point.LEARN
An object is in equilibrium only when there is no resultant force on it and no resultant moment on it. Balanced forces alone are not enough.LEARN
With several forces, add all the clockwise moments and all the anticlockwise moments about the pivot. A uniform beam's own weight acts at its middle, so it has a moment unless the pivot is there.LEARN
To test the principle: balance a metre rule at its centre with weights on both sides, measure each distance from the pivot, and show the total clockwise and anticlockwise moments are equal.LEARN

1.5.3Centre of gravity

The centre of gravity is the point through which all the weight of an object can be taken to act. For a uniform object it lies on every line of symmetry, so for a uniform ruler, rectangular sheet or ring it is at the centre.LEARN
To find the centre of gravity of a flat irregular sheet: hang it freely from a pin and mark the vertical line of a plumb line from the pin. Repeat from a second hole. The centre of gravity is where the two lines meet.LEARN
A tilted object, when released, falls back onto its base if the vertical line down from its centre of gravity passes inside the base. It topples if the line passes outside the base.LEARN
An object is more stable when its centre of gravity is lower or its base is wider: it must tilt further before it topples.LEARN

1.6 ◆Momentum

p=mvp = mvLEARN
Momentum is mass × velocity, in kg m/s. It is a vector: choose a positive direction and give momentum the other way a minus sign.LEARN
impulse=FΔt=Δ(mv)\text{impulse} = F\Delta t = \Delta(mv)LEARN
Impulse is force × the time the force acts for. The impulse of the resultant force equals the change in momentum, final minus initial, and its unit N s is the same as kg m/s.LEARN
F=ΔpΔtF = \frac{\Delta p}{\Delta t}LEARN
Resultant force = change in momentum ÷ time taken, the rate of change of momentum. For the same change in momentum, a longer time gives a smaller average force: this is how airbags and crumple zones work.LEARN
Conservation of momentum: in a collision or explosion, total momentum before = total momentum after, provided no resultant force from outside acts on the objects.LEARN

1.7.1Energy

The seven energy stores: internal (thermal), kinetic, gravitational potential, elastic (strain), chemical, nuclear and electrostatic. Light, sound and electrical work transfer energy; they are not stores.LEARN
Energy is transferred between stores by mechanical work (forces), electrical work (currents), heating, and waves (electromagnetic, sound and others).LEARN
Conservation of energy: energy cannot be created or destroyed, only transferred from one store to another, so the total stays the same. Energy in = useful energy out + wasted energy.LEARN
Ek=12mv2E_\text{k} = \tfrac{1}{2}mv^2LEARN
ΔEp=mgΔh\Delta E_\text{p} = mg\Delta hLEARN
In ΔEp=mgΔh\Delta E_\text{p} = mg\Delta h, Δh\Delta h is the change in vertical height, not the distance along a slope, and g=9.8 N/kgg = 9.8\ \text{N/kg} near the Earth's surface.LEARN
With no friction or air resistance, the energy a falling object loses from its gravitational potential store all goes into its kinetic store. For an object falling from rest: mgΔh=12mv2mg\Delta h = \tfrac{1}{2}mv^2.LEARN
Sankey diagram: each arrow's width is proportional to the energy it carries. Useful energy usually goes straight on and wasted energy branches off. The energies out add up to the energy in.LEARN

1.7.2Work

W=Fd=ΔEW = Fd = \Delta ELEARN
Work done = energy transferred. A force that moves an object does mechanical work; an electric current does electrical work.LEARN
In W=FdW = Fd, dd is how far the object moves in the direction of the force. A force does no work on an object that doesn't move, or that moves at right angles to the force.LEARN
Work and energy are both measured in joules: 1 J=1 N m1\ \text{J} = 1\ \text{N m}, the work done when a force of 1 N1\ \text{N} moves an object 1 m1\ \text{m} in the direction of the force.LEARN
Lifting at a steady speed: the lifting force equals the weight, so the work done by the lifting force is weight × height gained.LEARN
Rearranged: F=WdF = \frac{W}{d} and d=WFd = \frac{W}{F}. On level ground, when the braking force is the only force slowing a vehicle, a constant braking force times the braking distance (the distance it travels while braking) equals the energy taken from its kinetic store.LEARN

1.7.3Energy resources

efficiency=useful energy outputtotal energy input×100%\text{efficiency} = \frac{\text{useful energy output}}{\text{total energy input}} \times 100\%LEARN
efficiency=useful output powertotal input power×100%\text{efficiency} = \frac{\text{useful output power}}{\text{total input power}} \times 100\%LEARN
In a power station, fossil fuels, biofuels and nuclear fuel heat water in a boiler into steam; in geothermal power, hot rocks underground turn water into steam. The steam spins a turbine, which drives a generator.LEARN
Hydroelectric, tidal, wave and wind power need no boiler: moving water or air drives the turbine or generator directly. Solar cells turn light straight into electrical power; solar panels heat water.LEARN
Non-renewable: fossil fuels and nuclear fuel. Renewable: biofuels, hydroelectric, tides, waves, wind, solar and geothermal.LEARN
Compare resources by renewability, availability (where), reliability (when), scale (how much) and environmental impact. Wind, waves and solar depend on the weather or daylight.LEARN
A more efficient device transfers a larger fraction of its input energy usefully. The rest is wasted, usually as thermal energy to the surroundings. Efficiency can never be more than 100%.LEARN
The Sun's radiation is where most resources get their energy. The exceptions are geothermal, nuclear fuel and tides.LEARN
The Sun releases energy by nuclear fusion. Research is under way to use fusion to generate electrical power on a large scale.LEARN

1.7.4Power

P=WtP=ΔEtP = \frac{W}{t} \qquad P = \frac{\Delta E}{t}LEARN
Power is the work done per unit time, or the energy transferred per unit time.LEARN
Power is measured in watts: 1 W=1 J/s1\ \text{W} = 1\ \text{J/s}, 1 kW=1000 W1\ \text{kW} = 1000\ \text{W}, 1 MW=1 000 000 W1\ \text{MW} = 1\,000\,000\ \text{W}.LEARN
Rearranging P=ΔEtP = \frac{\Delta E}{t} gives ΔE=Pt\Delta E = Pt and t=ΔEPt = \frac{\Delta E}{P}, where ΔE\Delta E is the energy transferred and tt the time. With the power in W and the time in s, the energy is in J.LEARN
Doing the same work in less time needs more power. Power says how fast energy is transferred, not how much in total or how efficiently.LEARN

1.8Pressure

Pressure is force per unit area, with the force at right angles to the surface. Its unit is the pascal: 1 Pa=1 N/m21\ \text{Pa} = 1\ \text{N/m}^2. With an area in cm², pressure is in N/cm².LEARN
p=FAp = \frac{F}{A}LEARN
A bigger force on the same area gives a bigger pressure. The same force on a smaller area gives a bigger pressure (knife, nail); on a larger area it gives a smaller pressure (snowshoes, wide tyres).LEARN
In a liquid at rest, the pressure increases with depth below the surface and with the density of the liquid. It doesn't depend on the shape or width of the container.LEARN
Δp=ρgΔh\Delta p = \rho g \Delta hLEARN

Which method when

'Find the density of an irregular solid that sinks, such as a stone' → mass on a balance; volume = rise in the measuring-cylinder reading once it is fully under water (or the overflow from a full displacement can); then ρ=mV\rho = \dfrac{m}{V}, with g and cm³ giving g/cm³ (1.4)LEARN
'Find the period of a pendulum' → time 2020 complete oscillations (out and back) from a fixed marker at the centre of the swing, repeat and take the mean, then divide by the number of oscillations (1.1)LEARN
'Find the speed from a straight section of a distance–time graph' → read the distance and time at both ends of that section and divide the change in distance by the change in time; the end reading ÷ its time works only if the section starts at the origin (1.2)LEARN
'Find the distance travelled from a speed–time graph made of straight lines' → find the area under the line: a rectangle (speed × time) where the speed is constant, a triangle (12\tfrac{1}{2} × base × height) where it changes steadily from or to zero, a rectangle plus a triangle where it changes steadily between two non-zero speeds, then add the parts (1.2)LEARN
'A see-saw or beam balances with one force each side of the pivot: find a force or a distance' → with the beam light, or uniform and pivoted at its centre, set clockwise moment = anticlockwise moment, F1d1=F2d2F_1 d_1 = F_2 d_2, measuring each perpendicular distance from the pivot, not from the end (1.5.2)LEARN
'Find the constant braking force from the braking distance' → on level ground with the brakes the only thing slowing it, the work done by the brakes equals the kinetic energy removed, so F=WdF = \dfrac{W}{d} with WW in J (1.7.2)LEARN
'Find the useful power of a student running upstairs or a motor lifting a load at a steady speed' → work done = weight × vertical height gained, then divide by the time in seconds (1.7.4)LEARN
'Find the pressure a table or vehicle exerts on level ground' → the force is its weight (W=mgW = mg), the area is all the legs or wheels in contact added together, then p=FAp = \dfrac{F}{A} with N and m² for Pa (1.8)LEARN

◆Which method when

'A uniform metre rule balances on a pivot away from its 50 cm mark: find a weight' → the rule's own weight acts at the 50 cm mark and has a moment too; add all the clockwise and all the anticlockwise moments about the pivot and set the totals equal (1.5.2)LEARN
'Given a driving force, resistive forces and the mass, find the acceleration' → find the resultant force first (forces the other way count as negative), then a=Fma = \dfrac{F}{m}; the acceleration is in the direction of the resultant force (1.5.1)LEARN
'An object's weight on Earth is given: find its weight on the Moon or Mars' → find its mass with Earth's gg, m=Wgm = \dfrac{W}{g}; the mass is the same there, so multiply it by the new gg (1.3)LEARN
'Two trolleys collide and stick together, or push apart from rest: find a velocity' → choose a positive direction, then set total momentum before = total momentum after (no outside resultant force), adding both masses if they stick (1.6)LEARN
'A ball bounces back off a wall: find the impulse or the average force' → give the two velocities opposite signs, find m(v−u)m(v - u), then divide by the contact time (1.6)LEARN
'Explain how an airbag or crumple zone protects the driver' → the change in momentum is the same, the stopping time is longer, so F=ΔpΔtF = \dfrac{\Delta p}{\Delta t} is smaller (1.6)LEARN
'An object falls or slides from rest, ignore air resistance and friction: find its speed' → set mgΔh=12mv2mg\Delta h = \tfrac{1}{2}mv^2 with Δh\Delta h the vertical drop, then take the square root (1.7.1)LEARN

2 Thermal physics

2.1.1States of matter

Solid: fixed shape and fixed volume; does not flow; very hard to compress.LEARN
Liquid: fixed volume but no fixed shape (takes the shape of the part of the container it fills); flows; very hard to compress.LEARN
Gas: no fixed shape or volume (fills any closed container); flows; easily compressed; much lower density than a solid or a liquid.LEARN
Melting: solid to liquid. Freezing (solidification): liquid to solid. Boiling and evaporation: liquid to gas. Condensation: gas to liquid.LEARN
At a given pressure, a pure substance is a solid below its melting point, a liquid between its melting and boiling points, and a gas above its boiling point.LEARN
A change of state does not change the mass. Liquid to gas makes the volume much larger and the density much smaller; gas to liquid does the reverse.LEARN

2.1.2Particle model

Solid: close together, regular pattern, vibrate about fixed positions. Liquid: close together, irregular arrangement, move around each other. Gas: far apart, random arrangement, move fast in all directions.LEARN
The higher the temperature of a substance, the faster its particles move on average and the greater their average kinetic energy. Absolute zero, −273 °C-273\ \text{°C} (0 K0\ \text{K}), is the lowest possible temperature: the particles have the least possible kinetic energy.LEARN
Gas pressure comes from particles hitting the walls of the container. In a container of fixed size, the pressure rises if the particles hit the walls more often or harder: heating the gas or adding more gas does this.LEARN
Brownian motion: microscopic particles in a liquid or gas move at random because fast, randomly moving molecules hit them unevenly from all sides. It is evidence for the kinetic particle model.LEARN
Forces between particles: strong in solids (fixed positions) and liquids (close but moving past each other); very weak in gases, because the particles are far apart.LEARN
Gas pressure is the total force of the particle collisions on each unit area of a surface, p=FAp = \frac{F}{A}.LEARN
In Brownian motion, light, fast molecules (or atoms) move much heavier microscopic particles. The visible specks are microscopic particles, never molecules.LEARN

2.1.3Gases and the absolute scale of temperature

Fixed mass of gas, constant volume: a higher temperature makes the particles move faster on average, so they hit the walls more often and harder, and the pressure increases.LEARN
Fixed mass of gas, constant temperature: a smaller volume means the particles, at the same average speed, hit the walls more often, so the pressure increases.LEARN
T (in K)=θ (in °C)+273T\ (\text{in K}) = \theta\ (\text{in °C}) + 273, and θ=T−273\theta = T - 273. Absolute zero is 0 K0\ \text{K}; kelvin temperatures are never negative. A change of 1 K equals a change of 1 °C.LEARN
Boyle's law: when a fixed mass of gas is kept at a constant temperature, pV=constantpV = \text{constant}, so p1V1=p2V2p_1 V_1 = p_2 V_2. A graph of pp against VV is a curve; pp against 1V\frac{1}{V} is a straight line through the origin.LEARN

2.2.1Thermal expansion of solids, liquids and gases

Almost all substances expand when heated and contract when cooled (a gas in a rigid, sealed container cannot expand: its pressure rises instead). The mass stays the same, so as a substance expands its density decreases.LEARN
When a substance expands on heating, its particles move or vibrate faster and spread further apart on average. The particles themselves do not get bigger.LEARN
For the same temperature rise, a gas at constant pressure expands the most, a liquid less, and a solid the least.LEARN
Allowing for expansion: gaps in railway tracks and roads, expansion joints in bridges and slack in overhead cables leave room for expansion and contraction. Uses: liquid-in-glass thermometers and bimetallic strips in thermostats.LEARN
A heated bimetallic strip bends with the metal that expands more on the outside of the curve.LEARN
Solids expand least because strong forces hold their particles in fixed positions. Gases (at constant pressure) expand most because the forces between their particles are very weak.LEARN

2.2.2Specific heat capacity

When the temperature of an object rises, its internal energy increases. (Internal energy can also rise with no temperature change, while a substance melts or boils.)LEARN
A temperature rise means the average kinetic energy of all the particles in the object increases.LEARN
Specific heat capacity is the energy needed per unit mass per unit rise in temperature, in J/(kg °C)\text{J/(kg °C)}.LEARN
c=ΔEmΔθc = \frac{\Delta E}{m\Delta\theta}LEARN
ΔE=mcΔθ\Delta E = mc\Delta\theta holds only while there is no change of state. Use J, kg and the temperature rise in °C.LEARN
To measure cc: mass on a balance, energy from a joulemeter (or PtPt), temperature rise from a thermometer. Insulate, and stir a liquid. Energy lost to the surroundings makes the measured cc too high.LEARN

2.2.3Melting, boiling and evaporation

While a pure substance melts or boils, its temperature stays constant although energy is still supplied. This energy (latent heat) overcomes the forces between particles; it does not raise their average kinetic energy.LEARN
Pure water at standard atmospheric pressure melts (and freezes) at 0 °C0\ \text{°C} and boils at 100 °C100\ \text{°C}.LEARN
Condensation: gas particles slow down and attractive forces pull them close together. Solidification: the particles settle into fixed positions and only vibrate. Both give out energy; for a pure substance the temperature stays constant while they happen.LEARN
Evaporation: at any temperature, the more energetic particles escape from a liquid's surface. The particles left behind are slower on average, which cools the liquid.LEARN
Boiling happens throughout the liquid, with bubbles, only at the boiling point. Evaporation happens only at the surface, at any temperature.LEARN
Evaporation is faster when the liquid is warmer, its surface area is larger, or air moves faster over its surface.LEARN
An evaporating liquid cools below the temperature of the object it touches. Thermal energy then flows from the object into the liquid, so the object cools.LEARN

2.3.1Conduction

Conduction transfers thermal energy through a material from hotter to colder parts, without the material moving.LEARN
Metals are good thermal conductors (copper better than steel). Wood, plastic, wool and air are thermal insulators; water and most other liquids are poor conductors too.LEARN
To compare conductors, use rods of the same size, heated the same way, with the same wax at the same distance. The shortest time for the wax to melt means the best conductor.LEARN
Many solids, such as brick, concrete and glass, conduct better than insulators but much less well than metals.LEARN
All solids conduct by lattice vibrations passed from particle to neighbour. Metals also have free electrons that move through the metal and carry energy quickly, so metals conduct best.LEARN
Gases conduct badly: their particles are far apart and collide less often. Most liquids conduct badly: no lattice and no free electrons (liquid metals are the exception).LEARN

2.3.2Convection

Convection transfers thermal energy through liquids and gases (fluids) by the movement of the fluid itself. It cannot happen in solids, which cannot flow.LEARN
Fluid that is heated expands, so its density decreases and it rises through the cooler, denser fluid around it, which sinks to replace it. This loop is a convection current.LEARN
Fluid that is cooled contracts, so its density increases and it sinks through the warmer, less dense fluid around it.LEARN
To show convection: a purple crystal on the bottom of a beaker of water, heated just under the crystal at one side, or smoke drawn through a convection box with a candle under one chimney.LEARN

2.3.3Radiation

Thermal radiation is infrared radiation. All objects emit it, whatever their temperature.LEARN
Thermal radiation needs no medium, so it can travel through a vacuum. Conduction and convection cannot.LEARN
Dull black surfaces are the best absorbers and the worst reflectors of infrared. Shiny white or silvery surfaces are the best reflectors and the worst absorbers.LEARN
A good absorber is a good emitter: at the same temperature and surface area, a dull black surface emits infrared fastest and a shiny white or silvery one slowest.LEARN
Compare emitters with a Leslie cube of very hot water and an infrared detector at a fixed distance. Compare absorbers with wax-and-pin plates the same distance from a heater.LEARN
For the same type of surface, the rate of emission is greater at a higher surface temperature (same area) and for a larger surface area (same temperature).LEARN
An object's temperature is constant when it loses energy at the same rate as it gains energy. If it is not changing state, its temperature rises when it gains energy faster, and falls when it loses energy faster.LEARN
The Earth's temperature is steady when it radiates energy to space as fast as it absorbs energy from the Sun. More greenhouse gases (less infrared escapes) or less ice and snow (less sunlight reflected) make it gain energy faster than it loses it, so it warms until a new balance is reached.LEARN

2.3.4Consequences of thermal energy transfer

Pans: a metal base (good thermal conductor) passes energy quickly to the food; a plastic or wooden handle (thermal insulator) stays cool. Convection in the liquid spreads the energy through the pan.LEARN
A heater near the floor warms a room by convection: warm air expands, becomes less dense and rises; cooler, denser air sinks and flows back to the heater.LEARN
Vacuum flask: the vacuum has no particles, so no conduction or convection across it; silvered surfaces reflect infrared and emit little, reducing radiation; an insulating stopper reduces conduction and convection out of the top.LEARN
Conduction and convection need particles. Radiation does not, so it can cross a vacuum.LEARN
Open fire: radiation warms people in front of it; hot gases rise up the chimney by convection, drawing in fresh air; energy conducts through the grate and surrounding bricks.LEARN
Car radiator: the pumped coolant carries energy from the engine; it conducts through thin metal tubes and fins; air flowing past the large surface area carries it away by convection, with some radiation.LEARN

Which method when

'Explain, in terms of particles, why the pressure of a sealed gas changes' → first say what is kept constant, then chain: average speed of the particles (changed or not) → how often and how hard they hit the walls → force on the walls → pressure. Heated at constant volume: faster, so more often and harder; squeezed at constant temperature: same average speed, more often; more gas in the same space: more hits each second (2.1.2, 2.1.3)LEARN
'Explain why a bridge has a joint, a track has gaps or a cable hangs slack' (or why a hot tap loosens a lid) → decide hot (expands, longer) or cold (contracts, shorter), then name the problem that change would cause or the job it does. A hole in a heated solid gets bigger too (2.2.1)LEARN
'Calculate the energy supplied while it melts (or boils)' from a heater and a heating curve → the flat section is the change of state: read its length in time, change minutes to seconds, then ΔE=Pt\Delta E = Pt, assuming all the heater's energy goes into the substance (2.2.3)LEARN
'By which process is the energy transferred?' → test all three in turn: across a vacuum or through space, only radiation; through a solid such as a pan base or a spoon, conduction (a solid cannot flow, so no convection); warm liquid or gas moving and carrying the energy, convection; someone warmed in front of a fire, mainly radiation (2.3.1, 2.3.2, 2.3.3, 2.3.4)LEARN
'Explain how the whole kettle, pan or room warms up' (or how a fridge or air-conditioner cools it) → convection chain: heated fluid expands → density falls → it rises through the cooler, denser fluid, which sinks to replace it → a loop, the convection current. For a cooler, run it backwards: cooled, contracts, denser, sinks. Say 'less dense', never 'heat rises' (2.3.2, 2.3.4)LEARN
'Which surface should it have?' → decide whether the object should gain energy by radiation (in sunshine: dull black, the best absorber) or lose as little as possible (a hot flask or a survival blanket: shiny silver or white, the poorest emitter and best reflector); at the same temperature and surface area, dull black emits fastest (2.3.3)LEARN
'Plan a fair test of conductors or insulators' → change only the material. Rods: same size, same wax at the same distance, same hot water; the shortest time for the bead to fall is the best conductor. Insulated cups: same volume and starting temperature of water, same thickness and same time; the smallest temperature drop is the best insulator (2.3.1, 2.3.4)LEARN

◆Which method when

'Calculate the new pressure (or volume)' of a gas → check it is a fixed mass at constant temperature, then p1V1=p2V2p_1V_1 = p_2V_2 with the same units on both sides (kPa and cm³ are fine); sense check that the larger pressure goes with the smaller volume (2.1.3)LEARN
'Do these pressure and volume readings support Boyle's law?' → work out pVpV for every row; they support it if all the values are equal within experimental accuracy (about 10%). Seeing pp rise as VV falls is not enough (2.1.3)LEARN
'Find the specific heat capacity from a graph of temperature against time' (heater of power PP) → gradient =ΔθΔt= \dfrac{\Delta\theta}{\Delta t} (time in s) from the straight part, then c=Pm×gradientc = \dfrac{P}{m \times \text{gradient}} with mm in kg; valid while the heater supplies energy at a steady rate, little escapes and there is no change of state (2.2.2)LEARN
'Explain why its temperature rises, then stops rising' (a sheet in sunshine, or the Earth with more greenhouse gas) → compare the rate it gains energy with the rate it loses it: gains faster, temperature rises; equal, temperature steady; a hotter surface emits faster, so the rates move towards balance. This holds while the object is not changing state (2.3.3)LEARN

3 Waves

3.1General properties of waves

A wave transfers energy from place to place without transferring matter.LEARN
Transverse: vibration at 90∘90^\circ to the direction the wave moves (electromagnetic radiation, water waves, S-waves). Longitudinal: vibration parallel to it (sound, P-waves).LEARN
Amplitude: rest position to crest. Wavelength λ\lambda: crest to the next crest. Frequency ff: waves passing a point per second, in Hz. Neighbouring wavefronts are one wavelength apart.LEARN
v=fλv = f\lambdaLEARN
Ripple tank: a flat barrier shows reflection; a shallow region met at an angle shows refraction (slower, shorter wavelength, same frequency); a gap or an edge shows diffraction (same wavelength).LEARN
Diffraction through a gap is greatest when the gap is about one wavelength wide. For a gap wider than the wavelength, a narrower gap or a longer wavelength gives more spreading. Longer wavelengths bend further round an edge.LEARN

3.2.1Reflection of light

Normal: a line at 90∘90^\circ to the surface where the ray hits it. The angles of incidence and reflection are measured from the normal, not from the mirror.LEARN
Law of reflection: angle of incidence = angle of reflection, i=ri = r.LEARN
Plane mirror image: same size as the object; image-to-mirror distance = object-to-mirror distance; virtual. It is upright, with left and right swapped.LEARN
Virtual image: rays only appear to come from it, so it cannot be formed on a screen.LEARN
Plane mirror construction: the image is on the line from the object at 90∘90^\circ to the mirror, as far behind as the object is in front. A ray reaches an eye by reflecting where the line from the image to the eye crosses the mirror.LEARN

3.2.2Refraction of light

Normal: a line at 90∘90^\circ to the surface where the ray meets it. The angles of incidence and refraction are measured from the normal, never from the surface.LEARN
Into a material where light is slower (air into glass): bends towards the normal. Into one where it is faster (glass into air): bends away. Along the normal: no change of direction. The frequency never changes.LEARN
Critical angle: the angle of incidence, for light going into a material where it is faster, at which the angle of refraction is 90∘90^\circ.LEARN
Total internal reflection: light heading into a material where it would be faster is all reflected back when its angle of incidence is greater than the critical angle. Examples: prism periscopes and binoculars, sparkling diamonds.LEARN
n=speed in airspeed in the material(refractive index, no unit)n = \frac{\text{speed in air}}{\text{speed in the material}} \quad \text{(refractive index, no unit)}LEARN
n=sin⁡isin⁡r(i in air, r in the material)n = \frac{\sin i}{\sin r} \quad \text{(}i\text{ in air, }r\text{ in the material)}LEARN
n=1sin⁡c(c: critical angle, material to air)n = \frac{1}{\sin c} \quad \text{(}c\text{: critical angle, material to air)}LEARN
Optical fibres keep light inside by total internal reflection. In telecommunications they carry more information than copper cables, with less loss and no electrical interference.LEARN

3.2.3Thin lenses

Converging lens: rays parallel to the principal axis meet at the principal focus F. Diverging lens: they spread out as if from F on the incoming side.LEARN
Principal axis: the line through the centre of a lens at 90∘90^\circ to it. Focal length ff: the distance from the centre of the lens to F.LEARN
Ray rules for a converging lens: parallel to the axis → through F beyond the lens; through the middle → straight on; through F on the object's side → parallel to the axis.LEARN
Describe an image with one word from each pair: enlarged, same size or diminished; upright or inverted; real or virtual.LEARN
Real image: rays actually meet, so a screen can show it. Virtual image: spreading rays only seem to come from it, so no screen can.LEARN
Magnifying glass: a converging lens with the object closer than F gives a virtual, upright, enlarged image.LEARN
Short sight (distant objects focus in front of the retina): diverging lens. Long sight (near objects focus behind the retina): converging lens.LEARN

3.2.4Dispersion of light

Dispersion: a glass prism splits white light into its colours, because the glass refracts each colour through a different angle. Violet is refracted most, red least.LEARN
The visible spectrum, in order: red, orange, yellow, green, blue, indigo, violet (Richard Of York Gave Battle In Vain).LEARN
From red to violet, wavelength decreases and frequency increases. Red: longest wavelength, lowest frequency. Violet: shortest wavelength, highest frequency.LEARN
Monochromatic light has a single frequency (one colour). A prism refracts it but cannot split it.LEARN

3.3Electromagnetic spectrum

The spectrum by increasing frequency (decreasing wavelength): radio waves, microwaves and infrared; then visible light; then ultraviolet, X-rays and gamma rays.LEARN
In a vacuum, all electromagnetic waves move at one and the same speed. So a higher frequency means a shorter wavelength.LEARN
Speed of electromagnetic waves in a vacuum: 3.0×108 m/s3.0 \times 10^8\ \text{m/s}, and almost exactly the same in air.LEARN
Uses: radio (broadcasts, astronomy, RFID); microwaves (satellite TV, mobile phones, ovens); infrared (grills, remote controls, intruder alarms, thermal imaging, optical fibres); visible (vision, photography, lighting); ultraviolet (security marking, detecting fake notes, sterilising water); X-rays (medical and security scanning); gamma (sterilising food and equipment, detecting and treating cancer).LEARN
Harm from too much exposure: microwaves heat body cells internally; infrared burns skin; ultraviolet damages skin and eye cells (skin cancer, eye conditions); X-rays and gamma rays damage cells or cause mutations.LEARN
Satellites communicate mainly by microwaves. Satellite TV and some satellite phones use geostationary satellites; some satellite phones use low orbit satellites.LEARN
Phones and Wi-Fi: microwaves (pass through some walls, short aerial). Bluetooth: radio waves (pass through walls, weakened). Optical fibres: visible light or infrared (glass is transparent to them, high data rates).LEARN
Analogue signals vary continuously; digital signals have only two values, 1 and 0. Digital gives a higher data rate, and a greater range because it can be regenerated accurately.LEARN

3.4Sound

Sound is made by vibrating objects. It travels as a longitudinal wave: the particles of the medium vibrate backwards and forwards, parallel to the direction the sound travels.LEARN
Sound needs a medium (a solid, liquid or gas). It cannot travel through a vacuum.LEARN
Humans hear about 20 Hz20\ \text{Hz} to 20 000 Hz20\,000\ \text{Hz}. Ultrasound is sound with a frequency above 20 kHz20\ \text{kHz}.LEARN
A higher frequency gives a higher pitch. For the same note, a larger amplitude gives a louder sound.LEARN
Sound travels through air at about 330330–350 m/s350\ \text{m/s}. To measure the speed, time a sound over a large measured distance, repeat, and divide the distance by the average time.LEARN
An echo is sound reflected from a surface. When the source and the listener are in the same place, the echo travels to the surface and back: twice the distance to the surface.LEARN
Compression: particles closer together, pressure higher than normal. Rarefaction: particles further apart, pressure lower than normal. In general, sound is fastest in solids, slower in liquids and slowest in gases.LEARN
Ultrasound echoes are used in sonar, non-destructive testing of materials and medical scanning of soft tissue. Depth or distance == speed ×\times echo time ÷2\div 2, where the echo time runs from sending the pulse to receiving its echo.LEARN

Which method when

'Calculate the speed, frequency or wavelength of a wave' → v=fλv = f\lambda, rearranged, after converting cm to m and kHz or MHz to Hz; frequency from a count is waves passing ÷ time in s; across nn neighbouring wavefronts, λ\lambda = measured span ÷ (n−1)(n - 1) (3.1)LEARN
'Waves pass into shallow water' or 'light enters glass': what changes? → the frequency stays the same, because the source sets it; the speed and the wavelength both fall; the direction changes only if the waves meet the boundary at an angle (3.1, 3.2.2)LEARN
Plane-mirror angles and distances → measure angles from the normal, so a ray at x∘x^\circ to the mirror has i=90∘−xi = 90^\circ - x, then r=ir = i; the image is as far behind the mirror as the object is in front, so object to image is twice object to mirror (3.2.1)LEARN
'Does the ray leave the glass or reflect back?' → total internal reflection only if the light is heading into a material where it is faster (glass or water into air) and its angle of incidence is greater than the critical angle; below the critical angle most of it refracts out, bending away from the normal (3.2.2)LEARN
'Find the position and size of the image' for an object further from a converging lens than F → scale ray diagram: from the object's tip, a ray parallel to the axis bends through F on the far side, and a ray through the centre goes straight on; the image tip is where they cross; convert back with the scale (3.2.3)LEARN
'Calculate the speed of sound' or 'how far away is the cliff?' → v=stv = \dfrac{s}{t}, timing over a large distance and averaging repeats; an echo goes to the surface and back, so with the source and listener together, distance to the surface = speed × time from sound to echo ÷ 2 (3.4)LEARN

◆Which method when

'Which change makes the waves spread out more beyond the gap?' → compare the gap with the wavelength: spreading is greatest when the gap is about one wavelength wide; for a gap wider than the wavelength, a narrower gap or a longer wavelength gives more spreading; amplitude has no effect (3.1)LEARN
'Construct the image' or 'draw the ray that reaches the eye' for a plane mirror → rule a line from the object at 90∘90^\circ to the mirror and mark the image the same distance behind; join image to eye, and the ray reflects where that line crosses the mirror (3.2.1)LEARN
'Calculate the refractive index or the critical angle' → n=sin⁡isin⁡rn = \dfrac{\sin i}{\sin r} with ii in air and both angles from the normal, or nn = speed in air ÷ speed in the material; then sin⁡c=1n\sin c = \dfrac{1}{n} for light going from the material into air (3.2.2)LEARN
'Object closer to a converging lens than F' or 'how is the lens used as a magnifying glass?' → draw the same two rays, then extend them backwards as dashed lines; they cross on the object's side at a virtual, upright, enlarged image (3.2.3)LEARN
'Find the wavelength or frequency of an electromagnetic wave' with no speed given → recall 3.0×108 m/s3.0 \times 10^8\ \text{m/s} in a vacuum or air, then v=fλv = f\lambda; dividing by 10−710^{-7} is multiplying by 10710^{7} (3.3)LEARN

4 Electricity and magnetism

4.1Simple phenomena of magnetism

Like poles repel; unlike poles attract. A magnet attracts unmagnetised magnetic materials at either pole, so only repulsion proves an object is a magnet.LEARN
Magnetic materials (iron, steel, nickel, cobalt) are attracted by a magnet and can be magnetised. Non-magnetic materials, including copper and aluminium, are not.LEARN
Induced magnetism: a magnetic material near a magnet becomes a magnet, with the opposite pole at the end nearest the magnet's pole.LEARN
Soft iron is easy to magnetise and loses its magnetism easily (temporary magnets, electromagnet cores). Steel is harder to magnetise but keeps its magnetism (permanent magnets).LEARN
A magnetic field is a region where any magnetic pole feels a force. Its direction is the direction of the force an N pole would feel there.LEARN
Outside a bar magnet, field lines run from N to S, never cross, and crowd together at the poles. Plot them with a compass, or show the pattern with iron filings.LEARN
The closer together the field lines, the stronger the field. Magnetic forces come from the interaction between magnetic fields.LEARN

4.2.1Electric charge

There are two kinds of charge, positive and negative. Like charges repel; unlike charges attract.LEARN
Charging a solid by rubbing moves only electrons. Gain electrons: negative. Lose electrons: positive.LEARN
Repulsion proves an object is charged. Attraction doesn't, because a charged object also attracts small uncharged objects.LEARN
Conductors (metals, graphite) have free electrons that carry charge through them. Insulators (plastic, rubber, glass, dry wood) have none, so charge cannot flow through them.LEARN
Charge is measured in coulombs (C). An electric field is a region where a charge experiences a force. Its direction at a point is the way a positive charge there would be pushed.LEARN
Field patterns: straight radial lines around a point charge or outside a charged sphere (outwards for +, inwards for −). Between oppositely charged parallel plates: straight, parallel, evenly spaced lines from + to −.LEARN

4.2.2Electric current

Electric current is a flow of charge, measured in amperes (A). 1 mA=0.001 A1\ \text{mA} = 0.001\ \text{A}.LEARN
In a metal, the current is free electrons drifting along the wire. The positive ions stay in place and only vibrate.LEARN
An ammeter measures current and is connected in series. Choose the smallest range bigger than the expected current; if you can't estimate it, start on the largest range.LEARN
d.c. flows in one direction only (cells, batteries). a.c. keeps reversing direction (mains supply). A current that changes size but never reverses is still d.c.LEARN
I=QtI = \frac{Q}{t}LEARN
Current is the charge that passes a point each second. Round the circuit outside the supply, conventional current flows from + to −, and free electrons flow from − to +.LEARN

4.2.3Electromotive force and potential difference

E.m.f.: the electrical work a source does on each unit of charge it moves round a complete circuit. Measured in volts (V).LEARN
P.d.: the work done by each unit of charge as it passes through a component. Measured in volts (V), between two points. 1 V=1 J/C1\ \text{V} = 1\ \text{J/C}.LEARN
A voltmeter measures p.d. (or e.m.f.) and is connected in parallel. Choose the smallest range bigger than the expected p.d., and read the scale that matches the terminal used.LEARN
E=WQE = \frac{W}{Q}LEARN
V=WQV = \frac{W}{Q}LEARN

4.2.4Resistance

R=VI(resistance in Ω)R = \frac{V}{I} \quad \text{(resistance in } \Omega \text{)}LEARN
A resistor at constant temperature has a constant resistance: the current in it is directly proportional to the p.d. (Ohm's law).LEARN
To measure resistance: ammeter in series, voltmeter in parallel across the resistor, a variable resistor to get several readings; calculate R=VIR = \frac{V}{I} for each and take the mean.LEARN
Wires of the same metal at the same temperature: longer means more resistance (same thickness); thicker means less resistance (same length).LEARN
R∝l (same area)R∝1A (same length)R \propto l \ \text{(same area)} \qquad R \propto \frac{1}{A} \ \text{(same length)}LEARN
I–V graphs (II on the vertical axis): resistor at constant temperature, straight line through the origin; filament lamp, curve getting less steep as the filament heats and its resistance rises; diode, almost no current in reverse, current rises steeply in the forward direction.LEARN

4.2.5Electrical energy and electrical power

A circuit transfers energy from its source (a cell or the mains) to its components, and they transfer it to the surroundings. The current is not used up; the energy ends up spread out in the surroundings.LEARN
P=IV(power in W, current in A, p.d. in V)P = IV \quad \text{(power in W, current in A, p.d. in V)}LEARN
E=IVt(energy in J, with the time in s)E = IVt \quad \text{(energy in J, with the time in s)}LEARN
When a steady power is given, the energy transferred is E=PtE = Pt. With PP in W and tt in s, EE is in J.LEARN
One kilowatt-hour is the energy transferred by a 1 kW1\ \text{kW} appliance in 11 hour: 1 kW h=3.6×106 J1\ \text{kW h} = 3.6 \times 10^{6}\ \text{J}. It is a unit of energy, not power.LEARN
Cost of electricity: energy in kW h (power in kW ×\times time in hours) ×\times price per kW h.LEARN

4.3.1Circuit diagrams and circuit components

Circuit diagrams use the standard symbols, with wires drawn as straight lines and a dot at each junction.LEARN
Rectangle symbols: fixed resistor (empty), variable resistor (straight arrow through it), potential divider (arrow onto its side), thermistor (diagonal line with a flat foot), LDR (two arrows pointing in), heater (sections inside), fuse (line along its length).LEARN
NTC thermistor: its resistance falls as its temperature rises. LDR: its resistance falls as the light on it gets brighter.LEARN
With the supply p.d. unchanged, more resistance in a series circuit means a smaller current.LEARN
Fuse: its thin wire melts when the current rises above its rating, breaking the circuit. Relay: a small current in its coil closes a switch in a second circuit that carries a large current.LEARN
Potential divider: connected across a supply, it shares the supply p.d.; with a sliding contact, and the output taken between one end and the slider, it gives any p.d. from zero to the full supply p.d. Transformer: changes the size of an alternating p.d., and works only with a.c.LEARN
Diode: current passes only when its triangle points along the conventional current; in reverse almost no current flows. LED: a diode that gives out light when current passes in the forward direction.LEARN

4.3.2Series and parallel circuits

Series circuit: one loop, so the current is the same at every point.LEARN
R=R1+R2+R3(resistors in series)R = R_1 + R_2 + R_3 \quad \text{(resistors in series)}LEARN
Cells in series that all face the same way: add their e.m.f.s. A cell turned the other way subtracts its e.m.f.LEARN
Parallel circuit: the source supplies more current than any one branch carries. Two resistors in parallel have a combined resistance less than either one by itself.LEARN
Lamps in a lighting circuit are wired in parallel: each can be switched on its own, the rest stay lit if one breaks, and each gets the full supply p.d.LEARN
Total current into a junction = total current out, because charge is not used up or stored there. Series: the p.d.s across the components add up to the total p.d. Parallel: each branch has the same p.d. as the whole arrangement.LEARN
1R=1R1+1R2(two resistors in parallel)\frac{1}{R} = \frac{1}{R_1} + \frac{1}{R_2} \quad \text{(two resistors in parallel)}LEARN

4.3.3Action and use of circuit components

For a constant current, the p.d. across a conductor is larger when its resistance is larger (V=IRV = IR). In series, the component with the larger resistance has the larger p.d.LEARN
Sensor in series with a fixed resistor across a fixed supply p.d.: if the sensor's resistance rises, the current falls, so the p.d. across the fixed resistor falls and the p.d. across the sensor rises.LEARN
R1R2=V1V2(two resistors in series as a potential divider)\frac{R_1}{R_2} = \frac{V_1}{V_2} \quad \text{(two resistors in series as a potential divider)}LEARN
Variable potential divider, output taken between one end of the track and the slider: moving the slider sets the output p.d. anywhere from zero up to the full supply p.d.LEARN

4.4Electrical safety

Mains circuit: the live wire carries the high alternating p.d., the neutral wire stays near 0 V0\ \text{V}, and the earth wire joins a metal casing to the ground.LEARN
The switch and the fuse go in the live wire, so switching off or a melted fuse disconnects the appliance from the high p.d.LEARN
Hazards: damaged insulation (electric shock; also fire from a short circuit), overheating cables (fire), damp conditions (shock), overloaded sockets or extension leads (large total current, overheating, fire).LEARN
A fuse melts, and a trip switch opens, when the current goes above its rating or setting. A trip switch can be reset. Choose the smallest available rating above the appliance's normal current, I=PVI = \frac{P}{V}.LEARN
A metal casing must be earthed. A double-insulated appliance has a non-conducting casing and no earth wire, but still has a fuse, which protects the circuit and the cable.LEARN

4.5.1Electromagnetic induction

An e.m.f. is induced in a conductor when it cuts across magnetic field lines, or when the magnetic field through it changes. No relative movement and no change in the field means no e.m.f.LEARN
An induced e.m.f. drives an induced current only if the conductor is part of a complete circuit.LEARN
Demonstration: move a magnet in and out of a coil joined to a sensitive centre-zero meter. The needle deflects only while the magnet moves, opposite ways for in and out.LEARN
With everything else kept the same, the induced e.m.f. is bigger for faster movement, a stronger magnet or more turns on the coil. Reversing the movement (at the same speed) or the magnet reverses the e.m.f. but does not change its size.LEARN
Lenz's law: an induced e.m.f. acts in the direction that opposes the change causing it. A coil in a complete circuit repels an approaching pole and attracts a leaving one.LEARN
Fleming's right-hand rule, for a wire, motion and field all at right angles: thumb = motion, first finger = field (N to S), second finger = induced conventional current. The force on the induced current opposes the motion.LEARN

4.5.2 ◆The a.c. generator

Rotating-coil a.c. generator: the coil turns in a magnetic field, its sides cut field lines, and the induced e.m.f. reverses every half turn.LEARN
Slip rings turn with the coil, and fixed brushes press on them. They connect the turning coil to the circuit without the wires twisting; they do not make the current alternate.LEARN
Rotating-magnet generator: the field through a fixed coil reverses every half turn of the magnet, giving an alternating e.m.f. The coil doesn't move, so no slip rings are needed.LEARN
Rotating coil: the e.m.f. is zero when the plane of the coil is at right angles to the field lines, and is a peak or trough when it is parallel to them.LEARN
In a simple generator (one coil, two poles), one turn of the coil gives one cycle of e.m.f., so the frequency equals the number of turns each second.LEARN
With everything else kept the same: faster turning gives taller peaks and a higher frequency; a stronger magnet or more turns on the coil gives taller peaks at the same frequency.LEARN

4.5.3Magnetic effect of a current

A current makes a magnetic field. Around a long straight wire, the field lines are circles centred on the wire, at right angles to it.LEARN
Right-hand grip rule: thumb along the conventional current, fingers curl the way the field goes. Reverse the current and the field reverses.LEARN
A solenoid's field is like a bar magnet's, with straight, parallel lines inside it, away from the ends. Seen from one end, anticlockwise conventional current makes that end N; clockwise makes it S.LEARN
Plot the field with plotting compasses, which show pattern and direction. Iron filings show the pattern only.LEARN
Relay: a small current magnetises the coil's soft-iron core, which attracts an armature and closes contacts in a large-current circuit.LEARN
Loudspeaker: an alternating current in the coil makes a reversing field that interacts with a permanent magnet's field, so the coil and cone vibrate and make sound.LEARN
The field is strongest close to a wire, and strong and nearly uniform inside a solenoid. A bigger current gives a stronger field; a reversed current reverses it.LEARN

4.5.4Force on a current-carrying conductor

Motor effect: a conductor carrying a current across a magnetic field feels a force. The force is biggest when the current crosses the field lines at 90°, and zero when it runs along them.LEARN
Demonstration: a metal rod on rails, or a loose wire, between the poles of a magnet and connected to a d.c. supply. It moves when the current is switched on.LEARN
Reversing the current, or reversing the field, reverses the force. Reversing both leaves the force in its original direction. Reversing does not change the size of the force.LEARN
The force is at 90° to the current and at 90° to the field. Fleming's left-hand rule, for a current crossing the field at 90°: first finger = field (N to S), second finger = conventional current, thumb = force.LEARN
A beam of charged particles moving across a magnetic field is deflected. Positive particles: current in their direction of motion. Electrons and beta particles: current opposite to their motion. Charges at rest, or moving along the field lines, feel no magnetic force.LEARN

4.5.5The d.c. motor

A coil carrying a current in a magnetic field has forces in opposite directions on its two sides, which can turn it. The turning effect is biggest when the plane of the coil lies along the field lines, and zero when it is at right angles to them.LEARN
The turning effect on the coil is increased by more turns on the coil, a bigger current or a stronger magnetic field. Reversing either the current or the field reverses the direction of turning, not its size; reversing both leaves the direction unchanged.LEARN
In a d.c. motor the split-ring commutator reverses the coil's current every half turn, as the coil passes the position at right angles to the field. So the turning effect always acts the same way and the coil keeps turning in one direction.LEARN
The brushes are fixed contacts that press on the turning commutator. They connect the coil to the supply without the wires twisting.LEARN

4.5.6The transformer

A transformer is two coils of insulated copper wire on a soft-iron core. It works only with a.c., because only a changing magnetic field induces a voltage in the secondary.LEARN
Step-up: more turns on the secondary than the primary, so the output voltage is bigger. Step-down: fewer turns on the secondary, so the output voltage is smaller.LEARN
VpVs=NpNs\frac{V_\text{p}}{V_\text{s}} = \frac{N_\text{p}}{N_\text{s}}LEARN
Transmission: a step-up transformer at the power station, step-down transformers near the users. For the same power, raising the voltage lowers the current, so less energy is wasted heating the cables and thinner, cheaper cables can be used.LEARN
How it works: a.c. in the primary makes a changing magnetic field; the soft-iron core links it to the secondary; the changing field induces an alternating e.m.f. across the secondary.LEARN
IpVp=IsVs(100% efficient transformer)I_\text{p}V_\text{p} = I_\text{s}V_\text{s} \quad \text{(100\% efficient transformer)}LEARN
P=I2R(power wasted in a cable)P = I^2R \quad \text{(power wasted in a cable)}LEARN

Which method when

'Test whether a steel bar is a magnet' → bring each end of it near each pole of a known magnet: repulsion proves it is a magnet; attraction proves nothing, because a magnet attracts unmagnetised steel at either pole (4.1)LEARN
'Deduce the charge on each object' from which ones attract or repel → start from the object whose charge you know: repulsion means the same sign; attraction between two charged objects means opposite signs, but a charged object also attracts an uncharged one (4.2.1)LEARN
'State the reading' on an analogue ammeter or voltmeter → use the scale for the terminal in use; one small division = the gap between two labelled marks ÷ the number of divisions in it; count on from the labelled mark below the pointer, to the nearest half division, looking straight at the pointer (4.2.2, 4.2.3)LEARN
'Calculate the current' in one loop of cells and resistors → add the e.m.f.s of the cells facing the same way (subtract any turned round) and add the resistances, then I=VRI = \dfrac{V}{R} with the total e.m.f. and the total resistance; the current is the same at every point in the loop (4.3.2)LEARN
'How do the meter readings change when it gets darker (or warmer)?' for a sensor in series with a fixed resistor and a fixed supply → chain the links: sensor's resistance, total resistance, current, then V=IRV = IR for the fixed resistor; a voltmeter across the sensor changes the opposite way to the fixed resistor's p.d. (4.3.1, 4.3.3)LEARN
'Calculate the cost of running an appliance' with the power in W or the time in minutes → change to kW and hours first, multiply them to get the energy in kW h, then multiply by the price per kW h (4.2.5)LEARN
'Which fuse should be fitted?' given the appliance's power and the mains p.d. → find the normal current with I=PVI = \dfrac{P}{V} (power in W), then choose the smallest available rating above it, never the nearest one below (4.4)LEARN
'Which way does the meter needle swing now?' after the magnet or its motion is changed → count the reversals from the first test: reversing the pole or the direction of motion swings it the other way, doing both cancels out, and a magnet held still gives no reading (4.5.1)LEARN
'Which end of the solenoid is the N pole?' → look at that end: anticlockwise conventional current makes it N, clockwise makes it S; or curl your right-hand fingers round the turns with the conventional current and your thumb points to N (4.5.3)LEARN
'Calculate the output voltage' or 'the number of turns needed' for a transformer → write VpVs=NpNs\dfrac{V_\text{p}}{V_\text{s}} = \dfrac{N_\text{p}}{N_\text{s}}, rearrange for the unknown, then check the direction: fewer turns on the secondary must give a smaller output voltage (step-down) (4.5.6)LEARN

◆Which method when

'Calculate the p.d.' when the energy, the current and the time are given → find the charge first with Q=ItQ = It (current in A, time in s), then V=WQV = \dfrac{W}{Q} (4.2.3)LEARN
'Same metal, same length, twice the diameter: find the new resistance' → the area changes by the diameter factor squared (×4\times 4), and R∝1AR \propto \dfrac{1}{A}, so the resistance is a quarter (4.2.4)LEARN
'Find the p.d. across one of two resistors in series across a supply' when no current is given → split the supply p.d. in the ratio of the resistances, R1R2=V1V2\dfrac{R_1}{R_2} = \dfrac{V_1}{V_2} with V1+V2V_1 + V_2 = the supply p.d.; the larger resistor takes the larger share (4.3.3)LEARN
'Which pole forms at this end of the coil?' as a magnet moves near a coil in a complete circuit → use Lenz's law: the coil opposes the change, so an approaching pole meets a like pole (repelled) and a leaving pole meets an unlike pole (attracted) (4.5.1)LEARN
'Determine the direction of the force' on a wire or a beam of charged particles crossing a magnetic field → mark the field from N to S and the conventional current (opposite to the motion of electrons or beta particles), then use Fleming's left-hand rule; the force is at 90° to both, and a current along the field lines feels none (4.5.4)LEARN
'Find the frequency' from the e.m.f.–time graph of a simple a.c. generator (one coil, two poles) → count the complete cycles and divide by the time they take; one cycle is one turn of the coil, so this is also the number of turns each second (4.5.2)LEARN
'The transmission voltage is doubled, for the same power: what happens to the power wasted in the cables?' → I=PVI = \dfrac{P}{V} halves the current, then P=I2RP = I^2R in the same cable gives a quarter of the wasted power (4.5.6)LEARN

5 Nuclear physics

5.1.1The atom

An atom has a tiny, positively charged nucleus at its centre, with negatively charged electrons in orbit around it. A neutral atom has as many electrons as protons, so it has no overall charge.LEARN
An atom forms a positive ion by losing electrons and a negative ion by gaining electrons. The nucleus does not change. Counting a proton as +1+1 and an electron as −1-1, charge on an ion = number of protons − number of electrons.LEARN
Alpha particles fired at thin metal foil: most pass straight through, so the atom is mostly empty space with a very small nucleus. A few are pushed away, so the nucleus is positive. A very small number bounce back, so the nucleus holds most of the atom's mass.LEARN

5.1.2The nucleus

A nucleus is made of protons and neutrons (nucleons). Electrons orbit outside it. Relative charges: proton +1+1, neutron 00, electron −1-1.LEARN
Proton number (atomic number) ZZ = number of protons. Nucleon number (mass number) AA = number of protons + number of neutrons.LEARN
number of neutrons=A−Z\text{number of neutrons} = A - ZLEARN
Nuclide notation ZAX^{A}_{Z}\text{X}: nucleon number at the top left, proton number at the bottom left of the chemical symbol.LEARN
Isotopes are atoms of one element with the same proton number but different numbers of neutrons. An element can have more than one isotope.LEARN
Relative charge on a nucleus =+Z= +Z, its proton number. Relative mass of a nucleus =A= A, its nucleon number.LEARN
Fission: a large nucleus splits into two smaller nuclei. Fusion: two small nuclei join into a larger one. In both, the nucleon and proton numbers balance, the products have slightly less mass, and the lost mass is released as energy.LEARN

5.2.1Detection of radioactivity

Background radiation is the ionising radiation present around us all the time.LEARN
Most background radiation comes from four sources: radon gas, which is in the air; rocks and buildings; what we eat and drink; and cosmic rays.LEARN
Ionising radiation is measured with a detector (such as a Geiger–Müller tube) connected to a counter.LEARN
Count rate = number of counts ÷ time taken, in counts/s or counts/minute. Multiply a rate in counts/s by 60 to get counts/minute. Readings vary at random, so count for longer or average repeats.LEARN
Corrected count rate = measured count rate − background count rate, with both in the same unit.LEARN

5.2.2The three types of nuclear emission

Emission from a nucleus is spontaneous (no outside cause, so temperature and chemical changes don't affect it) and random in direction.LEARN
Alpha: a helium nucleus (2 protons, 2 neutrons), charge +2+2. Beta: a fast electron from the nucleus, charge −1-1. Gamma: an electromagnetic wave, no charge.LEARN
Ionising: alpha most, then beta, gamma least. Penetrating: gamma most, then beta, alpha least.LEARN
Stopped by: alpha, paper or a few cm of air; beta, a few mm of aluminium. Gamma is only reduced, by several cm of lead.LEARN
Moving the same way across the same electric or magnetic field, alpha and beta bend in opposite directions and beta bends more (tiny mass). Gamma is not deflected.LEARN
Alpha is the most ionising because it has the largest charge and, typically, more kinetic energy than beta. Gamma has no charge, so it ionises least.LEARN

5.2.3Radioactive decay

Radioactive decay: an unstable nucleus changes and gives out an alpha or beta particle and/or gamma radiation.LEARN
Decay is spontaneous (nothing outside the nucleus causes it) and random (you cannot predict when a nucleus will decay, or which one is next).LEARN
Alpha and beta decay change the proton number, so the nucleus becomes a different element. Gamma emission leaves both the proton number and the nucleon number unchanged: the element stays the same.LEARN
A nucleus can be unstable because it has too many neutrons for its number of protons, because it is too heavy, or both. Decay makes it more stable; beta decay reduces the excess of neutrons.LEARN
neutron→proton+electron\text{neutron} \to \text{proton} + \text{electron}LEARN
ZAX→Z−2A−4Y+24α{}^{A}_{Z}\text{X} \to {}^{A-4}_{Z-2}\text{Y} + {}^{4}_{2}\alphaLEARN
ZAX→Z+1AY+−1 0β{}^{A}_{Z}\text{X} \to {}^{A}_{Z+1}\text{Y} + {}^{\,0}_{-1}\betaLEARN
Gamma: ZAX→ZAX+γ^{A}_{Z}\text{X} \to {}^{A}_{Z}\text{X} + \gamma. In every decay equation the top numbers balance and the bottom numbers balance.LEARN

5.2.4Half-life

Half-life: the time for half of the unstable nuclei of an isotope in a sample to decay. It is the same for any amount of that isotope.LEARN
In each half-life, the nuclei left, the mass of the isotope and the count rate from it (background ignored or subtracted) all halve: 12\frac{1}{2}, 14\frac{1}{4}, 18\frac{1}{8}, … after 11, 22, 33 half-lives.LEARN
Halving chain (background ignored or subtracted): count the arrows, not the numbers. Time taken = number of half-lives × half-life.LEARN
From a decay curve (background ignored): halve the count rate at a starting time, go across to the curve, then straight down to read the time. Half-life = that time − the starting time. Check with a second halving.LEARN
With background in the readings: subtract it, halve the corrected count rate, then add the background back for a measured reading. A measured decay curve levels off at the background count rate.LEARN
Isotope choice: smoke alarm, alpha with a long half-life; food, equipment and cancer treatment by gamma beams from outside the body, gamma with a long half-life; paper thickness, beta with a long half-life; medical tracer for diagnosis, gamma with a half-life of a few hours.LEARN

5.2.5Safety precautions

Ionising radiation damages cells by ionising their atoms. It can kill cells, cause mutations (changes to DNA) and cause cancer.LEARN
A radioactive source can't be switched off. Store it in a lead-lined box, locked in a cabinet with a hazard sign.LEARN
Move a source with long-handled tongs, at arm's length and pointing away from people. Use it for as short a time as possible, then put it straight back.LEARN
Against a source outside the body, precautions cut the dose in three ways: less exposure time, more distance from the source, or a shield that absorbs the radiation.LEARN
Shield by type: paper stops alpha and a few mm of aluminium stops beta. Thick lead or concrete only reduces gamma.LEARN

Which method when

'How many protons, neutrons and electrons?' or 'What is the charge on this particle?' → protons =Z= Z (the bottom number) and neutrons =A−Z= A - Z; a neutral atom has ZZ electrons; charge = number of protons − number of electrons, leaving neutrons out, so losing electrons gives a positive ion and gaining them a negative one; the same ZZ with a different AA means isotopes of one element (5.1.1, 5.1.2)LEARN
'Which radiation does the source give out?' from absorber readings → compare each reading with the background count rate: a clear drop when paper goes in means alpha; a further clear drop with a few mm of aluminium means beta; still clearly above background behind the aluminium means gamma; a drop no bigger than the random variation means nothing was stopped. Alpha only reaches a detector a few cm from the source (5.2.2)LEARN
Half-life questions with background ignored → from a table or a decay curve, halve a count rate (not the time) and read how long it takes to fall to that value, then check with a second halving; for 'how much is left after…' or 'how long until…', number of half-lives = time ÷ half-life, then a halving chain: count the arrows, not the numbers (5.2.4)LEARN

◆Which method when

'What does each result of alpha-particle scattering show?' → most go straight through: the atom is mostly empty space with a very small nucleus; a few are deflected: the nucleus is positive, with its charge packed into a tiny space; a very small number bounce back: the nucleus also holds most of the atom's mass (5.1.1)LEARN
'Complete the equation' for fission, fusion or a decay → write every particle with both numbers (24α^{4}_{2}\alpha, −1 0β^{\,0}_{-1}\beta, 01n^{1}_{0}\text{n}; γ\gamma adds to neither total), then make the top numbers add to the same total on each side, and the bottom numbers too; alpha decay lowers AA by 4 and ZZ by 2, beta decay raises ZZ by 1 and leaves AA the same (5.1.2, 5.2.3)LEARN
Paths of the three emissions in an electric or magnetic field across the beam → γ\gamma goes straight on (no charge); α\alpha and β\beta bend opposite ways and β\beta bends much more (tiny mass); between charged plates, α\alpha bends towards the negative plate and β\beta towards the positive; in a magnetic field, use the left-hand rule with the current along the motion of α\alpha but against the motion of β\beta (5.2.2)LEARN
Half-life from readings or a decay curve that include background → subtract the background count rate (in the same unit) from every reading to get the corrected count rate, find the half-life from those values, and add the background back if the question wants a detector reading; a measured curve levels off at the background, not at zero (5.2.1, 5.2.4)LEARN
'Explain why this isotope is used' → make two points. The radiation type, for how far it must get and how strongly it ionises: alpha ionises the air in a smoke alarm but cannot escape it; beta is partly absorbed by paper, so it measures paper thickness; gamma gets out of a body and through packaging or thick metal. The half-life: long for a source that must keep working for years, a few hours for a tracer inside a patient (5.2.4)LEARN
'Explain how this precaution protects the worker' (a source outside the body) → name the idea, then link it to less radiation absorbed: less time near the source, a smaller dose; more distance, the radiation has spread out (and air absorbs alpha within a few cm); a shield matched to the radiation absorbs it, though lead only reduces gamma (5.2.5)LEARN

6 Space physics

6.1.1The Earth

The Earth spins on its tilted axis once in about 24 hours. This gives day and night, and makes the Sun appear to rise in the east and set in the west.LEARN
The Earth orbits the Sun once in about 365 days. Because its tilted axis points the same way all year, the hemisphere tilted towards the Sun has summer; the seasons are not caused by the Earth's distance from the Sun.LEARN
The Moon takes about a month to orbit the Earth. As it moves, we see different amounts of its sunlit half, so its phases repeat about once a month.LEARN
v=2πrTv = \frac{2\pi r}{T}LEARN
In v=2πrTv = \frac{2\pi r}{T}, rr is the average radius of the orbit, measured from the centre of the body being orbited, and TT is the orbital period.LEARN

6.1.2The Solar System

The Solar System: one star (the Sun), eight planets, minor planets (dwarf planets such as Pluto, and asteroids), moons that orbit the planets, and comets.LEARN
Planets in order: Mercury, Venus, Earth, Mars, (asteroid belt), Jupiter, Saturn, Uranus, Neptune. The inner four are small and rocky; the outer four are large and gaseous.LEARN
Accretion model: gravity pulled a rotating cloud of gas and dust into an accretion disc. The Sun formed at the centre and the planets clumped together in the disc. It was hot near the Sun (only rock and metal stayed solid) and cold far out (cores that gathered gas).LEARN
A planet's surface field strength depends on its mass (for similar-sized planets, more mass gives a stronger field). The field weakens with distance from the planet.LEARN
The Sun has about 99.8% of the Solar System's mass, so the planets orbit it. The Sun's gravitational attraction keeps them in orbit.LEARN
Time for light or radio waves to cross space: t=svt = \frac{s}{v} with v=3.0×108 m/sv = 3.0 \times 10^8\ \text{m/s} (given in Core questions; Extended: recall it).LEARN
Orbits are elliptical, with the Sun off-centre unless the orbit is nearly circular. With no friction in space, its total energy (kinetic + gravitational potential) stays constant, so an orbiting object is fastest closest to the Sun, where its gravitational potential energy is least.LEARN
A planet further from the Sun is where the Sun's field is weaker: its orbital speed is lower and its orbital period is longer.LEARN

6.2.1The Sun as a star

The Sun is a medium-sized star, made mostly of hydrogen and helium.LEARN
The Sun gives out most of its energy as infrared, visible light and ultraviolet: three neighbouring regions of the electromagnetic spectrum.LEARN
A star's energy comes from nuclear reactions in its centre. In a stable star such as the Sun, the reaction is fusion (not fission): hydrogen becomes helium.LEARN

6.2.2Stars

A galaxy contains many billions of stars. Our Sun is one star in the galaxy called the Milky Way.LEARN
The other stars in the Milky Way are much further from the Earth than the Sun is.LEARN
A light-year is a distance, not a time: the distance light travels through the vacuum of space in one year.LEARN
One light-year =9.5×1015 m= 9.5 \times 10^{15}\ \text{m}.LEARN
Every star: cloud of gas and dust (with hydrogen) → protostar (collapsing under gravity and heating up) → stable star (inward gravity balanced by an outward force caused by the very high temperature at its centre). When most of the hydrogen in its centre has become helium: most stars → red giant → planetary nebula with a white dwarf; much more massive stars → red supergiant → supernova → nebula with a neutron star or black hole.LEARN

6.2.3The Universe

Our galaxy, the Milky Way, is just one of billions of galaxies in the Universe. It measures about 100 000100\,000 light-years across.LEARN
Redshift: the observed wavelength of electromagnetic radiation from a receding star or galaxy is longer than the wavelength emitted. The light we receive from distant galaxies is redshifted when compared with the same light on Earth.LEARN
Distant galaxies' redshift is evidence for an expanding Universe, and supports the Big Bang theory.LEARN
The CMBR is microwave radiation arriving from every direction. It was produced shortly after the Universe formed, and the expansion has stretched it into the microwave region.LEARN
H0=vdH_0 = \frac{v}{d}LEARN
In H0=vdH_0 = \frac{v}{d}, vv is the speed a galaxy moves away (found from its redshift) and dd is its distance (found from the brightness of a supernova in it). The current estimate is H0=2.2×10−18 /sH_0 = 2.2 \times 10^{-18}\ \text{/s}.LEARN
1H0=dv\frac{1}{H_0} = \frac{d}{v}LEARN
1H0=dv\frac{1}{H_0} = \frac{d}{v} estimates the age of the Universe, about 14 billion years, assuming the galaxies have always moved apart at today's speeds. It is about the same for every distant galaxy, which is evidence that all matter was once at a single point.LEARN

Which method when

'Explain why it is summer in one hemisphere and winter in the other' → use the tilt: the Earth's tilted axis points the same way in space all through its 365-day orbit, so the hemisphere leaning towards the Sun has a higher Sun (light on a smaller area) and longer days; distance from the Sun is not the cause (6.1.1)LEARN
'How long does light or a radio signal take to travel between two objects in space?' → t=svt = \dfrac{s}{v} with v=3.0×108 m/sv = 3.0 \times 10^8\ \text{m/s} (given in Core questions; Extended: recall it) and ss in m, then convert to minutes if asked; for a star NN light-years away, its light takes NN years (6.1.2, 6.2.2)LEARN
'Use the accretion model to explain why the inner planets are rocky and the outer planets gaseous' → make separate points: a rotating cloud of gas and dust containing many elements; gravity pulls it in and it flattens into an accretion disc; material clumps together into planets; near the Sun it was hot, so only rock and metal stayed solid; far out it was cold, so large cores formed and their gravity pulled in gas (6.1.2)LEARN
'What does the light from distant galaxies tell us about the Universe?' → compare it with light from the same elements on Earth: every line has a longer observed wavelength (redshift), so the galaxies are moving away; redshift in every direction means the Universe is expanding, which supports the Big Bang theory (6.2.3)LEARN

◆Which method when

'Calculate the orbital speed' or 'find the orbital period' → v=2πrTv = \dfrac{2\pi r}{T} or T=2πrvT = \dfrac{2\pi r}{v}, with rr the average radius of the orbit measured from the centre of the body being orbited (add the planet's radius to a height above its surface), rr in m and TT in s for vv in m/s (6.1.1)LEARN
'Explain why a comet moves fastest when it is closest to the Sun' → conservation of energy: with no friction in space, its kinetic energy + gravitational potential energy stays constant; moving towards the Sun its gravitational potential energy falls, so its kinetic energy and speed rise, and both are greatest at the closest point (6.1.2)LEARN
'Calculate the Hubble constant' or 'find how fast a galaxy recedes, or how far away it is' → H0=vdH_0 = \dfrac{v}{d}, rearranged, with vv in m/s (from the redshift) and dd in m (from the brightness of a supernova in the galaxy), so H0H_0 is in /s; from a graph of vv against dd, H0H_0 is the gradient, keeping the powers of ten on both axes (6.2.3)LEARN
'Estimate the age of the Universe' → 1H0=dv\dfrac{1}{H_0} = \dfrac{d}{v} gives the time in s; divide by about 3.15×107 s3.15 \times 10^7\ \text{s} per year; it is only an estimate, because it assumes the galaxies have always moved apart at today's speeds (6.2.3)LEARN

7 Experimental skills

7.1Apparatus, techniques and safety

Diagrams: simple side views, label lines that touch each part, and a double-headed arrow between the exact points measured.LEARN
Too small or too quick to measure well? Measure many identical ones (sheets, turns, oscillations) and divide by the number.LEARN
Justify a choice with a reason: smaller scale divisions on a range that still reaches the reading, no reaction time (light gates), or a larger quantity to measure.LEARN
Safety: name the hazard in this experiment, then the precaution that reduces it, such as standing up near hot water or a sand tray under masses.LEARN
Accurate readings: eye level at right angles to the scale, bottom of a water meniscus, tare the balance, stir and wait for a thermometer, time from a marker at the centre of a swing.LEARN

7.2Planning investigations

Independent variable: what you change. Dependent variable: what you measure. Control variables: anything else that could affect the result, kept the same so the test is fair.LEARN
To control a variable, say how you keep it the same, such as setting the same current with a variable resistor and an ammeter. Explain why: it also affects the dependent variable.LEARN
Values: at least five, with units, evenly spaced over a wide range.LEARN
Justify apparatus or a technique with a reason, such as a range that reaches the reading with scale divisions small compared with it, or timing 10 oscillations to get a larger time to measure.LEARN
Plan: apparatus, method, control variables, a risk and its precaution, a results table, and how to reach a conclusion.LEARN
Results table: independent variable first, headings as quantity / unit, columns for repeats and the mean. Plot the dependent variable against the independent variable.LEARN
A reasoned prediction gives the expected change and the physics reason. At IGCSE, a numerical prediction is supported if the measured value differs from it by 10% or less of the predicted value.LEARN

7.3Taking and recording measurements

Analogue scale: value of one small division = gap between two labels ÷ number of divisions. Read to the nearest half division when the divisions are wide enough.LEARN
Digital display: record every digit shown, including a final zero, and convert mA to A if the table needs it.LEARN
Zero error: true value = reading − zero reading. If the zero reading is negative, subtracting it adds its size.LEARN
Check each reading is sensible; if not, check and measure again. Never change a reading to fit.LEARN
To find a pattern, take at least five values of the independent variable over a wide range. Repeat readings that can vary, and calculate a mean.LEARN
Tables: headings quantity / unit, independent variable first, the same decimal places down a column of readings, set by the instrument.LEARN

7.4Graphs, conclusions and evaluation

Graphs: axes labelled quantity / unit, an easy scale filling over half the grid, one thin best-fit line or smooth curve.LEARN
gradient=change in ychange in x\text{gradient} = \frac{\text{change in } y}{\text{change in } x}LEARN
Gradient: use a triangle covering over half the line, corners on the line. Unit = yy unit ÷ xx unit.LEARN
Directly proportional: a straight line through the origin. A straight line that misses the origin is linear but not proportional.LEARN
At IGCSE, two results agree within experimental accuracy if their difference is 10% or less of one of them (the predicted value, if there is one).LEARN
Random error scatters readings both ways: repeat and take a mean to reduce its effect. Systematic error, such as a zero error, shifts every reading the same way: correct the readings or the instrument.LEARN
Anomaly: repeat it if you can; otherwise leave it out of the mean and best-fit line, and say so.LEARN
Improvements are specific and say how they help: repeat and take a mean, a wider range, time many oscillations, light gates.LEARN

Which method when

'Find the thickness of one sheet' or 'the period of a pendulum' (too small or too quick for one good reading) → measure many identical ones together, such as a stack or 20 complete oscillations, then divide by the number; the reading or reaction-time error is shared between them (7.1)LEARN
'Choose the apparatus and justify your choice' → an instrument whose range reaches the reading and whose scale divisions are small compared with it, or light gates with an electronic timer for times well under a second; give the reason (smaller divisions, no reaction time), not just 'more accurate' (7.1, 7.2)LEARN
'Identify a hazard and a precaution' → name what could cause harm in this experiment (hot water, falling masses, hot wires), then the precaution that matches it and how it helps, such as a tray of sand under hanging masses; 'be careful' scores nothing (7.1)LEARN
'Describe how and explain why a variable is controlled' → name the control variable, the apparatus that sets it the same for every reading (an ammeter and a variable resistor for the current), and why: it also affects the dependent variable, so if it changed you could not tell which caused the change (7.2)LEARN
'Suggest a suitable number and range of values' → at least five values, with units, evenly spaced over the widest range the apparatus allows; for nn evenly spaced values the step is (largest − smallest) ÷ (n−1)(n - 1) (7.2)LEARN
'Record the reading' or 'complete the table' → work out one small division (gap between labels ÷ number of divisions), read to the nearest half division when the divisions are wide enough, subtract any zero reading (a negative one adds), and write it under a quantity / unit heading to the instrument's decimal places (7.3)LEARN
'Determine the gradient' or 'the intercept' → a triangle covering more than half of the best-fit line, with both corners read from the line, not the table; unit = yy unit ÷ xx unit; the intercept is the value of yy at x=0x = 0, so extend the line there if the xx scale starts above 0 (7.4)LEARN
'Is yy directly proportional to xx?' or 'do the results support the prediction?' → proportional only if the best-fit line is straight and passes through the origin; for two values, find the difference as a percentage of the predicted value (with no prediction, of one of the values): at IGCSE, 10% or less means equal within the limits of experimental accuracy; quote both values (7.2, 7.4)LEARN
'Suggest an improvement' or 'what should she do about this result?' → name the biggest problem and a specific fix: readings scattered both ways (random error) → repeat and calculate a mean; every reading shifted one way (systematic, such as a zero error) → correct the readings or the instrument; a control variable that changed → keep it the same and say how; an anomaly → repeat it, or leave it out of the mean and best-fit line and say so (7.4)LEARN
Follows the Cambridge IGCSE Physics 0625 syllabus (2026 to 2028). Not affiliated with Cambridge.