2.2.3 · CorePaper 1Paper 2Paper 3Paper 4

Melting, boiling and evaporation

In a minute

While a pure substance melts or boils, energy keeps going in but its stays the same. In , the fastest particles escape from a 's surface at any temperature, so the liquid left behind cools. That is why sweating cools you down.

You'll be able to

  • Explain why the temperature stays the same while a substance melts or boils, even though energy is still being supplied.
  • State the and points of pure water at standard atmospheric pressure.
  • Describe what the particles do when a gas condenses and when a liquid solidifies.
  • Describe evaporation as the more energetic particles leaving the surface, and explain why it cools the liquid.
  • Compare boiling with evaporation, and say how temperature, surface area and moving air change the rate of evaporation.
  • Explain how an evaporating liquid cools the object it is touching.
Before you start3 quick questions on what this builds on
Check yourself
What is the name for the change of state from a gas to a liquid?
Check yourself
The temperature of a gas rises. What happens to its particles?
Check yourself
What is the of an object?

Revise first: 1.7.1 Energy, 2.1.1 States of matter and 2.1.2 Particle model

Melting and boiling: energy in, no temperature rise

Heat ice from a freezer steadily, with a thermometer in it. The reading climbs to 0 °C0\ \text{°C}, then stays there until all the ice has melted, though energy is still going in.

In a solid, attractive forces hold the particles in fixed positions. During , the energy supplied overcomes these forces so the particles can move around each other. Their average kinetic energy does not rise, so the stays the same until all the solid has melted.

works the same way: the energy separates the particles until they escape as a gas, and the temperature stays at the boiling point until all the liquid has gone.

The is not lost. It raises the substance's as potential energy of the particles, while their average kinetic energy stays the same.

Heating curve for pure water heated steadily from minus 20 degrees Celsius. The temperature rises steeply while the ice warms, stays flat at 0 degrees Celsius while the ice melts, rises again, less steeply, while the water warms, stays flat at 100 degrees Celsius for a longer time while the water boils, then rises while the steam warms −20 0 100 temperature / °C time ice warms melting ice + water water warms boiling water + steam steam warms flat sections: energy goes in, temperature stays the same
A heating curve for water. Each flat section is a change of state.

Learn these values: at standard atmospheric pressure, pure water melts (and freezes) at 0 °C0\ \text{°C} and boils at 100 °C100\ \text{°C}. At lower pressure, such as up a mountain, water boils below 100 °C100\ \text{°C}.

Worked exampleA pan of water has been boiling on a gas hob for several minutes, with the flame still on. Explain why a thermometer in the water still reads 100 °C100\ \text{°C}.

Try it first, then reveal one step at a time.

  1. Say where the energy comes from, what it does to the particles, and what happens to their average kinetic energy.
Worked exampleA student heats a solid with a 40 W40\ \text{W} electric heater and records its temperature every half minute. It stays at 62 °C62\ \text{°C} from t=3.0 mint = 3.0\ \text{min} to t=8.5 mint = 8.5\ \text{min}, then rises again. Assume all the heater's energy goes into the substance. Calculate the energy supplied while it melts.

Try it first, then reveal one step at a time.

  1. The flat section is the melting: 8.5−3.0=5.5 min=5.5×60=330 s8.5 - 3.0 = 5.5\ \text{min} = 5.5 \times 60 = 330\ \text{s}.
Check yourself
A pure solid is heated steadily from room temperature until it has become a gas. Its heating curve has two flat sections. Which part of the curve shows the substance boiling?

Condensation and solidification

and solidification reverse boiling and melting, so the substance gives energy out.

In a gas, the particles are far apart and move fast. As the gas cools, they slow down until attractive forces pull them close together. They can still move around each other, so they form a liquid: this is condensation.

Cool the liquid further and, at the melting point, attractive forces hold the particles in fixed positions in a regular pattern, where they can only vibrate. This is solidification (freezing).

During both changes a pure substance gives out latent heat and its temperature stays the same, so its cooling curve has a flat section.

Worked exampleOn a cold morning, droplets of water form on the inside of a car windscreen. Describe, in terms of particles, how the droplets form.

Try it first, then reveal one step at a time.

  1. Start with the water vapour particles, then say what happens when they meet the cold glass.
Check yourself
Which statement describes the particles of a substance as it solidifies?
Check yourself
Steam at 100 °C100\ \text{°C} condenses into water at 100 °C100\ \text{°C}. What happens to energy during this change?

Evaporation: the fastest particles escape

A puddle dries up on a cool day, far below 100 °C100\ \text{°C}. So a liquid can turn into a gas without boiling.

Particles in a liquid move at a range of speeds. A fast particle at the surface, moving outwards, can have enough energy to break free from its neighbours and escape into the air. This is evaporation. It happens only at the surface, at any temperature.

A container of liquid with particles drawn as circles, close together. Two fast particles have left the surface and move up into the air, with long arrows. A slower particle at the surface has a short arrow and is pulled back by its neighbours. The particles left in the liquid have a lower average kinetic energy fast particles escape from the surface slower particle: attractions pull it back particles left behind: lower average kinetic energy, so the liquid cools surface
Only the more energetic particles near the surface can escape.

The more energetic particles escape and the slower ones stay, so the particles left have a lower average kinetic energy. Evaporation cools the liquid that is left.

Worked exampleA shallow dish of water is left in a room at 25 °C25\ \text{°C}. After a few hours, a thermometer in the water reads a little below room temperature. Explain why.

Try it first, then reveal one step at a time.

  1. Say which particles escape, from where, and what that does to the particles left.
Check yourself
During evaporation, which particles leave the liquid?
Check yourself
A glass of water at room temperature is left on a shelf and slowly evaporates. What happens to the temperature of the water left in the glass?
Extended only

Boiling and evaporation both turn a liquid into a gas. Evaporation happens only at the surface, at any temperature, with no bubbles, and it cools the liquid. Boiling happens throughout the liquid, with bubbles, only at the boiling point; the liquid stays at that temperature while energy is supplied.

Extended only
Worked exampleDescribe three differences between boiling and evaporation.

Try it first, then reveal one step at a time.

  1. Compare both processes in each point, linking them with "but" or "while".
Extended only
Check yourself
Which statement is true of evaporation but not of boiling?

Faster evaporation, and how it cools an object Extended only

Three things make a liquid evaporate faster:

1. A higher temperature: more particles have enough energy to escape.

2. A larger surface area: more particles are at the surface, where they can escape.

3. Air moving over the surface: it carries escaped particles away before they can fall back into the liquid.

Worked exampleExplain why a hair dryer, which blows warm air, dries wet hair faster than leaving it to dry in still, cool air.

Try it first, then reveal one step at a time.

  1. The hair dryer changes two of the three factors: deal with each.
Check yourself
Which change would make the water on a freshly mopped floor evaporate more slowly?

An evaporating liquid on an object, such as sweat on skin, cools the object too:

1. Evaporation cools the liquid below the temperature of the object it touches.

2. Thermal energy flows from the warmer object into the cooler liquid.

3. That energy keeps evaporation going, so the object keeps losing energy and its temperature falls.

Worked exampleHand-sanitiser gel is at room temperature, yet your hands feel cold a few seconds after you rub it in. The gel contains alcohol, which evaporates quickly. Explain why your hands cool.

Try it first, then reveal one step at a time.

  1. First explain why the liquid cools, then which way energy flows between skin and liquid.
Check yourself
A metal can of drink is wrapped in a damp cloth, and the water in the cloth evaporates. In which direction is thermal energy transferred?

Common mistakes

  • Expecting a boiling liquid to keep getting hotter because the heater is still on. The energy separates the particles, so the temperature stays at the boiling point.
  • Saying the less energetic particles escape during evaporation. The more energetic ones escape, which is why the liquid left behind cools.
  • Drawing a heating curve as one straight slope. A pure substance has a flat section at its melting point and another at its boiling point.

Exam tips

  • "Explain" why evaporation cools: one linked step per sentence. The faster particles leave the surface; those remaining have a lower average kinetic energy; this lowers the temperature.
  • "Describe the differences" between boiling and evaporation (Extended): compare both in each point, such as "boiling happens throughout the liquid, but evaporation happens only at the surface".

Key takeaways

Learn thisWhile a pure substance melts or boils, its temperature stays constant although energy is still supplied. This energy (latent heat) overcomes the forces between particles; it does not raise their average kinetic energy.
Learn thisPure water at standard atmospheric pressure melts (and freezes) at 0 °C0\ \text{°C} and boils at 100 °C100\ \text{°C}.
Learn thisCondensation: gas particles slow down and attractive forces pull them close together. Solidification: the particles settle into fixed positions and only vibrate. Both give out energy; for a pure substance the temperature stays constant while they happen.
Learn thisEvaporation: at any temperature, the more energetic particles escape from a liquid's surface. The particles left behind are slower on average, which cools the liquid.
Learn thisBoiling happens throughout the liquid, with bubbles, only at the boiling point. Evaporation happens only at the surface, at any temperature.
Learn thisEvaporation is faster when the liquid is warmer, its surface area is larger, or air moves faster over its surface.
Learn thisAn evaporating liquid cools below the temperature of the object it touches. Thermal energy then flows from the object into the liquid, so the object cools.

Practise this

75 past-paper questions on Melting, boiling and evaporation in the 0625 Extended bank, each with a mark scheme and a worked explanation.

Practise Melting, boiling and evaporation →