Pressure
In a minute
tells you how concentrated a is: the force on each unit of area, . The same push on a small area gives a big pressure, which is why a sharp knife cuts and wide snowshoes help you sink less. In a liquid, the pressure gets bigger the deeper you go and the denser the liquid is. Extended adds the equation .
You'll be able to
- Define pressure as force per unit area, and use with the unit Pa (N/m²) or N/cm².
- Describe how changing the force or the area changes the pressure, using everyday examples.
- Describe how the pressure under the surface of a liquid depends on the depth and on the of the liquid.
- Use to calculate a change in pressure, a depth or a density in a liquid.
Before you start2 quick questions on what this builds on
Revise first: 1.3 Mass and weight, 1.4 Density and 1.5.1 Effects of forces
Pressure: force on each unit of area
Press your palm on a balloon and it squashes. Press a pin on it with the same force and it bursts. The force is the same; what changes is how much area it is spread over.
is the pressure, is the force in N and is the area in m². The unit of pressure is the pascal (Pa): . If the area is in cm², the pressure comes out in N/cm².
For an object resting on a flat, level floor, with nothing else pushing on it, the force on the floor is the object's . Rearrange the equation to find a force, , or an area, .
Try it first, then reveal one step at a time.
- Find the area in contact with the floor: .
- The force on the floor is the weight: .
- Write the equation and substitute: .
- . The area is in m², so the unit is Pa (or N/m²).
Try it first, then reveal one step at a time.
- The force is the weight, not the mass: .
- The weight rests on all four legs, so add their areas: .
- Substitute: .
- The data have 2 significant figures, so give 2.
Changing the force or the area
tells you two things. A bigger force on the same area gives a bigger pressure. The same force on a bigger area gives a smaller pressure.
To get a high pressure, make the area small. A knife blade, a needle point, the tip of a nail and the studs on a football boot all put the force onto a tiny area. The high pressure lets them cut or push into a material.
To get a low pressure, make the area large. Snowshoes, wide tractor tyres, wide rucksack straps and the broad foundations of a building all spread a weight over a large area. The low pressure means they sink in less and dig into you less.
Try it first, then reveal one step at a time.
- Say what stays the same: the force on the snow.
- Say what changes: the area in contact with the snow.
- Use to say what happens to the pressure, then link it to sinking.
- The hiker's weight is the same in boots or snowshoes, so the force on the snow is the same. Snowshoes have a much larger area in contact with the snow. Pressure is force divided by area, so the larger area gives a smaller pressure on the snow. With a lower pressure, the snow is pushed down less, so she sinks less.
Pressure in a liquid
A liquid has weight, so it pushes on everything under its surface. This is . It pushes in all directions: down on the bottom, sideways on the walls, and up on anything under the surface.
The deeper you go, the taller the column of liquid above you, pressing down. So the pressure increases with depth. Depth means the vertical distance below the surface.
At the same depth, a denser liquid gives a bigger pressure. Each cubic metre of it has more mass, so the liquid above presses down with more weight. Sea water gives a slightly bigger pressure than fresh water at the same depth.
Only the depth and the density matter. The shape or width of the container, and how much liquid it holds, make no difference. At the same depth in the same liquid, the pressure is the same in a narrow tube and in a wide tank.
Try it first, then reveal one step at a time.
- Compare the depths of the two taps below the water surface.
- Link the depth to the water above, and so to the pressure.
- Link the pressure to how fast the water comes out.
- The lower tap is at a greater depth below the water surface. There is more water above it, pressing down with more weight. So the water at the lower tap is at a greater pressure. The greater pressure pushes water out of the lower tap faster.
Calculating the pressure in a liquid Extended only
Picture a column of liquid of height standing on an area . Its volume is , so its mass is and its weight is . Divide this weight by the area , and the pressure it causes is .
is the change in pressure in Pa, is the density of the liquid in kg/m³, and is the change in depth in m. The symbol means "change in".
Measured from the surface, is the depth and is the pressure due to the liquid alone. Between two points in the liquid, is the vertical distance between them.
Try it first, then reveal one step at a time.
- Write the equation: .
- Substitute, with the depth in metres: .
- The depth has 2 significant figures, so give 2: , or in standard form.
Try it first, then reveal one step at a time.
- The change in depth is and the change in pressure is .
- Rearrange for the density: .
- Substitute: .
- Give 3 significant figures, as the pressure and depth have. The liquid is less dense than water, like an oil.
Common mistakes
- Using the area of one wheel, leg or foot when the weight rests on several. Add all the contact areas first.
- Multiplying force by area, or dividing area by force. Pressure is force ÷ area: .
- Putting a mass in kg into . The force is the weight, so find first.
- Mixing cm² and m². ; use N with m² for Pa, or N with cm² for N/cm².
- Thinking a wider container means a greater liquid pressure, or that a heavier object feels a greater liquid pressure at the same depth. Only the depth and the density of the liquid matter.
Exam tips
- "Define" pressure in words: force per unit area. If you write instead, say what each symbol means.
- "Calculate" a pressure: write the equation, then the numbers in it, then the answer with its unit: Pa (or N/m²) for an area in m², N/cm² for an area in cm².
- "Explain" an everyday example in linked steps: what stays the same (usually the force or weight), what changes (the area), what happens to the pressure, and what that does (sinks less, cuts more easily).
- For a liquid question, look only at the depth and the density of the liquid. Ignore the container's shape, the volume of liquid (except where it changes the depth) and the mass of any object in it.
Key takeaways
Practise this
76 past-paper questions on Pressure in the 0625 Extended bank, each with a mark scheme and a worked explanation.