4.5.6 · CorePaper 1Paper 2Paper 3Paper 4

The transformer

In a minute

A is two coils of wire on a soft-iron core. It changes the size of an alternating voltage: more turns on the output coil than on the input coil give a bigger voltage, fewer turns a smaller one. The grid uses transformers to send electricity along cables at a very high voltage, so the current is small and less energy is wasted heating the cables.

You'll be able to

  • Describe how a transformer is built, and use the words primary, secondary, step-up and step-down.
  • Use VpVs=NpNs\frac{V_\text{p}}{V_\text{s}} = \frac{N_\text{p}}{N_\text{s}} to find a voltage or a number of turns.
  • Describe how transformers are used to send electricity at high voltage, and state the advantages.
  • Explain how a transformer works, using .
  • Use IpVp=IsVsI_\text{p}V_\text{p} = I_\text{s}V_\text{s} for a 100% efficient transformer.
  • Use P=I2RP = I^2R to explain why cables waste less when the voltage is higher.
Before you start3 quick questions on what this builds on
Check yourself
A coil of wire is connected to a sensitive meter. Which of these induces an e.m.f. in the coil?
Check yourself
What is an (a.c.)?
Check yourself
An appliance has a power of 1150 W1150\ \text{W} on a 230 V230\ \text{V} supply. What is the current in it, in A?

Revise first: 4.1 Simple phenomena of magnetism, 4.2.2 Electric current, 4.2.4 Resistance, 4.2.5 Electrical energy and electrical power and 4.5.1 Electromagnetic induction

Inside a transformer

A changes an alternating voltage into a bigger or a smaller one. Mains electricity is about 230 V230\ \text{V} in many countries, for example, but a doorbell might need only 8 V8\ \text{V}.

It has two coils of insulated copper wire wound on a closed loop of soft iron, the core. The two coils are not joined to each other by any wire.

A simple transformer. A square ring of soft iron forms the core. On the left side of the ring is the primary coil, with 5 turns of insulated copper wire, connected to an a.c. supply. On the right side of the ring is the secondary coil, with 10 turns, connected to a lamp. The two coils are not joined by any wire. The secondary has more turns than the primary, so this is a step-up transformer. soft-iron core ~ a.c. supply primary coil input, 5 turns lamp secondary coil output, 10 turns
The secondary has more turns than the primary, so this transformer steps the voltage up.

The is connected to the a.c. supply: it is the input. The gives the output, to a lamp or any other device.

Each material has a job. Copper is a good conductor, so the coils waste little energy. The insulation stops the current jumping between turns. Soft iron is easily magnetised and demagnetised (a ), so it carries the magnetic field from one coil to the other.

A has more turns on the secondary coil than on the primary, so the output voltage is bigger than the input. A has fewer turns on the secondary, so the output voltage is smaller.

A transformer works only with . The changing current in the primary makes a changing , and only a changing field induces a voltage in the secondary (4.5.1). A steady d.c. makes a steady field, so there is no output, apart from a brief flick at the moment the d.c. is switched on or off.

Transformers have a high , but they still warm up: the current heats the coils and the changing field heats the core. This wasted energy goes to the thermal store of the surroundings.

Worked exampleDescribe the construction of a simple step-down transformer.

Try it first, then reveal one step at a time.

  1. Name the parts: two coils and a core.
Check yourself
The primary coil of a transformer has 2000 turns and the secondary has 150 turns. What type of transformer is it?
Check yourself
The primary coil of a transformer is connected to a battery, so a steady current flows in it. What does a voltmeter across the secondary coil read while the current stays steady?

How a transformer works Extended only

A transformer uses , step by step:

1. The alternating current in the primary coil makes a magnetic field, as in an . The current keeps changing size and direction, so the field does too.

2. The soft-iron core is magnetised by this field (). It links the field to the secondary coil, so the changing field passes through the secondary too.

3. A changing magnetic field through a coil induces an e.m.f. in it. The field keeps reversing, so the induced e.m.f. across the secondary is alternating.

4. If the secondary is part of a complete circuit, this e.m.f. drives an alternating current round it. An e.m.f. is induced in every turn and the turns add up, so more turns give a bigger output.

Worked exampleExplain how an alternating current in the primary coil of a transformer produces an alternating e.m.f. across the secondary coil.

Try it first, then reveal one step at a time.

  1. Start with the primary coil and the field it makes.
Check yourself
In a transformer, what links the primary coil to the secondary coil?

Voltages and turns

The voltages across the two coils are in the same ratio as their numbers of turns. Here VpV_\text{p} and VsV_\text{s} are the across the primary and secondary coils, and NpN_\text{p} and NsN_\text{s} are their numbers of turns.

Learn this
VpVs=NpNs\frac{V_\text{p}}{V_\text{s}} = \frac{N_\text{p}}{N_\text{s}}

To find the output voltage, rearrange to Vs=Vp×NsNpV_\text{s} = V_\text{p} \times \frac{N_\text{s}}{N_\text{p}}. Then check the answer makes sense: a step-down transformer must give a smaller voltage.

Worked exampleIn a battery charger, the transformer's primary coil of 4600 turns is connected to the 230 V230\ \text{V} mains. Its secondary coil has 100 turns. Calculate the output voltage.

Try it first, then reveal one step at a time.

  1. Write the equation: VpVs=NpNs\frac{V_\text{p}}{V_\text{s}} = \frac{N_\text{p}}{N_\text{s}}.
Worked exampleA transformer must change a 12 V12\ \text{V} a.c. supply into 330 V330\ \text{V}. Its primary coil has 160 turns. Calculate the number of turns needed on the secondary coil, and state the type of transformer.

Try it first, then reveal one step at a time.

  1. Rearrange the equation for NsN_\text{s}: Ns=Np×VsVpN_\text{s} = N_\text{p} \times \frac{V_\text{s}}{V_\text{p}}.
Check yourself
The input voltage to a transformer is 120 V120\ \text{V}. Its primary has 1500 turns and its secondary 375 turns. What is the output voltage, in V?
Check yourself
A transformer changes 230 V230\ \text{V} to 46 V46\ \text{V}. Its secondary coil has 90 turns. How many turns are on its primary coil?
Extended only

If a transformer is 100% efficient, no energy is wasted, so the into the primary equals the power out of the secondary. Electrical power is current × p.d., P=IVP = IV.

Extended only
Learn this
IpVp=IsVsI_\text{p}V_\text{p} = I_\text{s}V_\text{s}
Extended only

So when a 100% efficient transformer steps the voltage up, it steps the current down by the same factor.

Extended only
Worked exampleA 100% efficient transformer steps 230 V230\ \text{V} mains down to 11.5 V11.5\ \text{V} for a set of garden lights. The current in the secondary coil is 4.0 A4.0\ \text{A}. Calculate the current in the primary coil.

Try it first, then reveal one step at a time.

  1. Write the equation: IpVp=IsVsI_\text{p}V_\text{p} = I_\text{s}V_\text{s}.
Extended only
Check yourself
A 100% efficient transformer has 8 times as many turns on its secondary coil as on its primary coil. How does the secondary current compare with the primary current?

Sending electricity at high voltage

Power stations are often far from the towns they supply. The long cables have , so the current heats them and wastes energy.

How electricity reaches homes, as five boxes in a row joined by arrows from left to right. First, the power station generator. Second, a step-up transformer, which raises the voltage. Third, long cables on pylons, at a very high voltage with a small current. Fourth, step-down transformers, which lower the voltage in stages. Fifth, homes, which receive mains voltage. power station generator step-up transformer voltage raised cables on pylons very high voltage, small current step-down transformers voltage lowered in stages homes mains voltage electrical energy flows this way a smaller current in the long cables wastes less energy heating them
Step up at the power station, step down near the users.

1. At the power station, a step-up transformer raises the voltage to a very high value, often hundreds of thousands of volts.

2. Cables on pylons, or under the ground, carry the electricity across the country.

3. Near towns, step-down transformers lower the voltage in stages, down to the mains voltage used in homes.

A smaller current heats the cables less. This gives the advantages of high-voltage transmission: less energy is wasted as heat in the cables, so more of it reaches the users. Thinner, lighter and cheaper cables can also carry the smaller current.

Worked exampleA power station sends 60 MW60\ \text{MW} of electrical power along its cables at 400 kV400\ \text{kV}. Calculate the current in the cables.

Try it first, then reveal one step at a time.

  1. Convert to watts and volts: 60 MW=60×106 W60\ \text{MW} = 60 \times 10^6\ \text{W} and 400 kV=400×103 V400\ \text{kV} = 400 \times 10^3\ \text{V}.
Worked exampleState two advantages of transmitting electricity at a high voltage.

Try it first, then reveal one step at a time.

  1. "State" needs short answers, no long explanation.
Check yourself
Why is electricity sent across the country at a very high voltage?
Check yourself
A power line carries 18 MW18\ \text{MW} at 275 kV275\ \text{kV}. What is the current in the line, in A? Give your answer to 2 significant figures.
Extended only

The power wasted as heat in a cable depends on the current in it and its resistance RR:

Extended only
Learn this
P=I2RP = I^2R
Extended only

The current is squared. In the same cable, halve the current and the power wasted falls to a quarter. So stepping up the voltage, which cuts the current, makes a big difference.

Extended only
Worked exampleThe cables in the example above have a total resistance of 2.5 Ω2.5\ \Omega. The station sends 60 MW60\ \text{MW} at 400 kV400\ \text{kV}, so the current is 150 A150\ \text{A}. Calculate the power wasted in the cables.

Try it first, then reveal one step at a time.

  1. Write the equation: P=I2RP = I^2R.
Extended only
Worked exampleUse P=I2RP = I^2R to explain why less power is wasted in transmission cables when the voltage is higher.

Try it first, then reveal one step at a time.

  1. Link voltage to current first, for the same power.
Extended only
Check yourself
A fixed power is sent along a cable. The voltage is doubled. What happens to the power wasted in the cable?

Common mistakes

  • Turning the turns ratio upside down. In a step-down transformer the primary has more turns than the secondary; check your answer against this.
  • Extended: thinking a step-up transformer increases the current as well as the voltage. Energy is not created, so when the voltage goes up the current goes down.
  • Saying high-voltage transmission is "faster" or "safer". The advantage is a smaller current, so less energy is wasted heating the cables.
  • Forgetting to convert MW to W or kV to V before using P=IVP = IV. The current comes out a thousand or a million times wrong.
  • Extended: forgetting to square the current in P=I2RP = I^2R. In the same cable, halving the current cuts the wasted power to a quarter, not a half.

Exam tips

  • "Describe the construction": name two coils of insulated copper wire, a soft-iron core, and which coil has more turns. Each point can earn a mark.
  • "Calculate" with the turns equation: write it, substitute, then give the answer with its unit. Check that step-down gives a smaller voltage.
  • "State" the advantages of sending electricity at high voltage as two separate points, such as less energy wasted heating the cables and thinner, cheaper cables.
  • "Explain" how a transformer works (Extended): link every step: a.c. in the primary, changing magnetic field, core links it to the secondary, e.m.f. induced in the secondary.

Key takeaways

Learn thisA transformer is two coils of insulated copper wire on a soft-iron core. It works only with a.c., because only a changing magnetic field induces a voltage in the secondary.
Learn thisStep-up: more turns on the secondary than the primary, so the output voltage is bigger. Step-down: fewer turns on the secondary, so the output voltage is smaller.
Learn thisVpVs=NpNs\frac{V_\text{p}}{V_\text{s}} = \frac{N_\text{p}}{N_\text{s}}
Learn thisTransmission: a step-up transformer at the power station, step-down transformers near the users. For the same power, raising the voltage lowers the current, so less energy is wasted heating the cables and thinner, cheaper cables can be used.
Learn thisHow it works: a.c. in the primary makes a changing magnetic field; the soft-iron core links it to the secondary; the changing field induces an alternating e.m.f. across the secondary.
Learn thisIpVp=IsVs(100% efficient transformer)I_\text{p}V_\text{p} = I_\text{s}V_\text{s} \quad \text{(100\% efficient transformer)}
Learn thisP=I2R(power wasted in a cable)P = I^2R \quad \text{(power wasted in a cable)}

Practise this

26 past-paper questions on The transformer in the 0625 Extended bank, each with a mark scheme and a worked explanation.

Practise The transformer →