Magnetic effect of a current
In a minute
A current in a wire makes a around it: circles round a straight wire, and a pattern like a bar 's round a . Your right hand gives the field's direction. and loudspeakers both work by this magnetic effect of a current.
You'll be able to
- Describe and draw the pattern and direction of the field of a straight wire and of a solenoid, using the right-hand grip rule.
- Describe how to plot these fields, including their direction, with plotting compasses and iron filings.
- Explain how a relay and a loudspeaker use the magnetic effect of a current, and give examples of where each is used.
- Say where the field of a wire or a solenoid is strong or weak, and how it changes when the current is made bigger, smaller or reversed.
Before you start3 quick questions on what this builds on
Revise first: 4.1 Simple phenomena of magnetism, 4.2.1 Electric charge, 4.2.2 Electric current and 4.3.1 Circuit diagrams and circuit components
The field of a wire and of a solenoid
Any makes a around it. This is the magnetic effect of a current. Switch the current off and the field disappears.
Around a long straight wire, the are circles centred on the wire. Each circle lies in a plane at right angles to the wire, like rings threaded on it.
Try it first, then reveal one step at a time.
- Pattern: the field lines are circles round the wire, centred on it.
- Direction: point your right thumb away from you, along the current. Your fingers curl clockwise as you look along the wire.
- The field lines are circles centred on the wire, each at right angles to it. Looking along the wire, with the current flowing away from you, the field goes clockwise.
Inside a , away from its ends, the field lines are straight, parallel and evenly spaced. Outside, the pattern is like a bar magnet's: one end acts as an N pole and the other as an S pole.
To find the N end, curl the fingers of your right hand round the coil the way the current flows in the turns. Your thumb points to the N end. Or look at one end: if the current goes anticlockwise, that end is N; if clockwise, it is S.
Try it first, then reveal one step at a time.
- (a) Seen from an end, anticlockwise current means that end is an N pole.
- Check with the grip rule: fingers round the turns the way the current flows, and your thumb points right, to the N end.
- (b) Outside, the field goes from the N end round to the S end. Beside the middle, that is from right to left.
- (a) The right-hand end is the N pole. (b) The N end of the needle points to the left, towards the S end of the solenoid.
Plotting the field in the lab
You find the pattern and direction with plotting compasses, as you did for a bar magnet in 4.1. The N end of each needle points along the field where it sits.
For a straight wire, pass the wire vertically through a hole in a horizontal card. Connect it to a d.c. supply that can give a large current, a few amps, with a switch in the circuit.
1. Switch on. Put a plotting compass on the card near the wire and mark a dot at the N end of its needle.
2. Move the compass so the S end of its needle is over the dot, and mark the N end again. Carry on round the wire, then join the dots and add arrows the way the needles point.
3. Repeat further from the wire. You get circles centred on the wire. Reverse the current and every needle turns round: the field direction has reversed.
Iron filings sprinkled on the card, then tapped gently, show the circular pattern quickly. They show no direction, so you still need a compass for the arrows.
For a solenoid, push the coil through slots in a card so the card runs along its axis. Plot lines with a compass from one end, round the outside to the other end, and through the inside.
Try it first, then reveal one step at a time.
- Give the steps in order: set up, mark, move, repeat, join, arrow.
- Say where you start new lines, so the whole pattern appears.
- Thread the solenoid through a horizontal card so the card runs along its axis, and switch on the current. Place a plotting compass on the card near one end and mark a dot at the N end of its needle. Move the compass so the S end of its needle is over the dot, mark a new dot, and repeat. Join the dots with a smooth line, and add an arrow the way the N end of the needle points. Plot more lines, inside and outside the solenoid, starting from different points.
Relays and loudspeakers
An is a coil, often with a soft-iron core, that is magnetic only while a current flows. A relay and a loudspeaker each contain one.
A is a switch worked by an electromagnet, so a small current can switch a large one on and off. You met its circuit symbol in 4.3.1.
1. A small current flows in the coil, and the soft-iron core becomes a magnet.
2. The core attracts the soft-iron armature, which tips about its pivot and pushes the contacts together.
3. The closed contacts complete the second circuit, so a large current flows in it.
4. When the coil current stops, the core loses its magnetism at once: it is a . The spring pulls the armature back and the contacts open.
Relays in use: a car's starter motor, which needs a very large current, and street lights or mains heaters switched by a low-voltage sensor circuit.
Try it first, then reveal one step at a time.
- Start in the small-current circuit, then follow the chain: coil, armature, contacts, motor.
- Then say what the relay protects.
- Turning the switch lets a small current flow in the relay coil. The coil and its soft-iron core become an electromagnet. The electromagnet attracts the soft-iron armature, which closes the contacts. This completes the starter-motor circuit, so a large current flows and the motor turns. With a relay, only a small current passes through the ignition switch and its wires, so they can be thin and safe to handle.
A loudspeaker turns an electrical signal into sound. A coil fixed to a paper cone sits in the field of a strong permanent .
An alternating current in the coil makes a magnetic field that keeps reversing. This field and the magnet's field push the coil one way, then the other. So the coil and cone move in and out, at the same frequency as the current.
The vibrating cone pushes on the air and sends out sound waves. Loudspeakers are in headphones, earphones, phones, radios and televisions.
Try it first, then reveal one step at a time.
- Follow the chain: current, magnetic field, force, vibration, sound.
- The key word is alternating: the current keeps reversing, so the force does too.
- The alternating current in the coil produces a magnetic field that keeps changing direction. The coil's field and the permanent magnet's field interact, which puts a force on the coil. Each time the current reverses, the force reverses. So the coil and the cone vibrate in and out, at the frequency of the current. The cone makes the air vibrate, which sends out sound waves.
Field strength and changing the current Extended only
The closer the field lines, the stronger the field. Around a straight wire, the field is strongest close to the wire and gets weaker further away, so the circles are drawn further apart as they go out.
Inside a solenoid, the field is strong and nearly the same everywhere: the lines are parallel and evenly spaced. It weakens near the ends, where the lines spread out, and it is much weaker outside.
Increase the current and the field is stronger everywhere, with the same pattern, so draw the lines closer together. A smaller current gives a weaker field. Reversing the current reverses the field's direction but changes neither its pattern nor its strength.
Try it first, then reveal one step at a time.
- Treat the strength (the size of the current) and the direction (the way it flows) separately.
- Halving the current weakens the field everywhere. Reversing it reverses the direction.
- The field is still circles centred on the wire, strongest near the wire. It is weaker at every point, so the circles are drawn further apart. Its direction reverses: it was clockwise and is now anticlockwise, because the current now flows out of the page.
Common mistakes
- Using the left hand, or the direction of electron flow, for the grip rule. Use your right hand, with your thumb along the conventional current.
- Drawing solenoid field lines that cross, or that stop at the ends. Each line is a complete loop, through the inside from S to N and round the outside from N to S.
- Saying iron filings show the field's direction. They show only the pattern; a plotting compass shows the direction.
- Saying a relay's soft-iron core stays magnetised. It is a temporary magnet: it loses its magnetism when the coil current stops, and the spring opens the contacts.
Exam tips
- "Draw" the field of a solenoid: smooth lines that never cross, parallel inside, complete loops outside, the same above and below, with an arrow on every line.
- "Describe" an experiment: name the apparatus, give the steps in order, and say how you find the direction (the N end of a compass needle).
- "Explain" how a relay or loudspeaker works as a chain: current, magnetic field, force or attraction, movement. Each linked step is usually a mark.
Key takeaways
Practise this
32 past-paper questions on Magnetic effect of a current in the 0625 Extended bank, each with a mark scheme and a worked explanation.