4.5.2 · Extended onlyPaper 2Paper 4

The a.c. generator

In a minute

An turns a coil in a magnetic field, or turns a magnet beside a coil. The induced e.m.f. reverses every half turn, so the output is alternating. and brushes connect a turning coil to the outside circuit, and the coil's position tells you where the peaks and zeros of the e.m.f.–time graph fall.

You'll be able to

  • Describe how a rotating coil or a rotating magnet produces an alternating e.m.f., and why a rotating coil needs slip rings and brushes.
  • Sketch the e.m.f.–time graph of a simple a.c. generator, and link each peak, trough and zero to the position of the coil.
  • Read the number of turns and the from the graph, and show how faster turning, a stronger magnet or more turns change it.
Before you start3 quick questions on what this builds on
Check yourself
A coil is connected to a sensitive meter. When is an e.m.f. induced in the coil?
Check yourself
Which statement describes an ?
Check yourself
A string makes 45 complete vibrations in 0.50 s0.50\ \text{s}. What is its frequency, in Hz?

Revise first: 1.1 Physical quantities and measurement techniques, 1.7.3 Energy resources, 3.1 General properties of waves, 4.2.2 Electric current and 4.5.1 Electromagnetic induction

How an a.c. generator works

A transfers kinetic energy into electrical energy by . In the simplest , a coil of wire is turned between the poles of a magnet.

A simple a.c. generator. A rectangular coil of wire sits between the N pole of a magnet on the left and the S pole on the right, with magnetic field lines running across from N to S. The coil is fixed to an upright axle and turns with it, shown by a curved rotation arrow at the top. Below the coil, each end of the coil is joined to one of two metal slip rings on the axle, which turn with the coil. A fixed brush presses against each ring. Wires from the two brushes go to a lamp, completing the circuit. N S field lines run from N to S coil axle rotation slip rings (turn with the coil) brushes (fixed) lamp
A rotating-coil generator. Each slip ring is joined to one end of the coil.

1. As the coil turns, its sides cut across the magnetic field lines. So an e.m.f. is induced in the coil.

2. Each side moves one way across the field for half a turn, then back the other way for the next half.

3. When a side's motion reverses, its induced e.m.f. reverses too. So the e.m.f. changes direction every half turn: it is an alternating e.m.f.

4. Join the coil into a complete circuit, and this e.m.f. drives an round it.

Without slip rings, the wires from the coil would twist up as it turned. Each brush always touches the same ring, so it stays joined to the same end of the coil. So the output reverses each time the e.m.f. in the coil reverses.

A second kind of generator keeps the coil still and spins a magnet beside it. Each half turn, the magnet's poles swap places, so the field through the coil reverses and the induced e.m.f. alternates.

A rotating-magnet generator. A bar magnet spins on an axle at its centre, shown by a curved arrow. Beside it is a fixed coil of wire, whose two ends are joined straight to a lamp. A note says the coil does not move, so its wires join the lamp directly and no slip rings are needed. S N magnet spins on an axle fixed coil lamp The coil does not move, so its wires join the lamp directly: no slip rings.
Rotating magnet, fixed coil: no slip rings needed.

Slip rings are needed only when the coil turns. Don't confuse them with the split-ring commutator of a d.c. motor (4.5.5). A commutator swaps the connections every half turn, so the output would never reverse.

Worked exampleA small water wheel turns a coil between the poles of a magnet. The coil is connected through slip rings and brushes to a resistor. Describe how an alternating current is produced in the resistor.

Try it first, then reveal one step at a time.

  1. Start with the movement: the coil turns in the magnetic field.
Worked exampleA bicycle dynamo has a magnet that spins beside a fixed coil, which is wired to a lamp. Explain why the dynamo gives an alternating e.m.f., and why it needs no slip rings.

Try it first, then reveal one step at a time.

  1. The coil doesn't move here, so explain the e.m.f. with the changing field through the coil.
Check yourself
Why does a rotating-coil generator need slip rings and brushes?
Check yourself
The slip rings of an a.c. generator are replaced by a split-ring commutator. What happens to the current in the outside circuit?

The e.m.f.–time graph

Turn the coil at a steady speed and plot its e.m.f. against time. You get a smooth wave, above zero for one half turn and below zero for the next.

The size of the e.m.f. depends on how fast the sides of the coil are cutting field lines. That depends on the direction the sides are moving.

Plane of the coil at right angles to the field lines: the sides are moving along the field lines, parallel to them. They cut no field lines, so the e.m.f. is zero.

Plane of the coil parallel to the field lines: the sides are moving straight across the field lines. They cut field lines fastest, so the e.m.f. is at a peak or a trough.

Graph of e.m.f. against time for one turn of a generator coil: a smooth wave that starts at zero, rises to a peak after a quarter turn, falls to zero after half a turn, reaches a trough of the same size below the axis after three quarters of a turn, and is back to zero after one turn. Below the graph, five small views from above show the coil at each of these moments, turning clockwise between an N pole on the left and an S pole on the right. At the start, half turn and full turn the coil lies at right angles to the field, and arrows show its two sides moving along the field lines: the e.m.f. is zero. At a quarter turn and three quarters of a turn the coil lies along the field, and arrows show its two sides moving straight across the field lines: the e.m.f. is a peak and then a trough. The two sides are coloured differently, showing that they have swapped places between the peak and the trough. e.m.f. time 0 start N S e.m.f. zero ¼ turn N S e.m.f. peak ½ turn N S e.m.f. zero ¾ turn N S e.m.f. trough 1 turn N S e.m.f. zero
One turn, seen from above. The arrows show which way each side of the coil is moving.

At the trough, the two sides have swapped places compared with the peak. Each is cutting the field the opposite way, so the e.m.f. is just as big but in the opposite direction.

So the of the e.m.f. is the time for one turn, and its is the number of turns each second. A coil turning 25 times a second gives an e.m.f. of frequency 25 Hz25\ \text{Hz}, and each cycle takes 125=0.040 s\frac{1}{25} = 0.040\ \text{s}.

Worked exampleThe e.m.f.–time graph of a simple generator shows 6 complete cycles in 0.20 s0.20\ \text{s}. State how many turns the coil makes in this time, and calculate the frequency of the e.m.f.

Try it first, then reveal one step at a time.

  1. One complete cycle of e.m.f. comes from one turn of the coil, so the coil makes 6 turns in 0.20 s0.20\ \text{s}.

Turning the coil faster makes its sides cut field lines faster, so the peaks get taller. Each turn also takes less time, so the cycles get shorter and the frequency rises.

Worked exampleA generator's e.m.f. has a peak value of 4.0 V4.0\ \text{V} and a period of 0.080 s0.080\ \text{s}. The coil is then turned twice as fast, with nothing else changed. Describe how the e.m.f.–time graph changes, giving the new peak e.m.f. and the new period.

Try it first, then reveal one step at a time.

  1. Twice the speed means the sides cut field lines twice as fast, so the e.m.f. at each point of the turn is twice as big.
Two graphs of e.m.f. against time on the same axes, both starting at zero. The solid curve is the generator at its original speed: two complete cycles. The dashed curve is the same generator turning twice as fast: its peaks and troughs are twice as tall, and each cycle takes half as long, so it fits four cycles into the same time. e.m.f. time 0 one cycle, original speed one cycle, twice as fast original speed twice as fast
Twice as fast: twice the peak, half the period.

A stronger magnet, or more turns of wire on the coil, also makes the peaks taller. But the coil turns at the same speed, so the period and frequency don't change.

Check yourself
At which position of a generator coil is the induced e.m.f. zero?
Check yourself
At t=0t = 0 a generator coil lies parallel to the magnetic field and the e.m.f. is at a peak. What is the e.m.f. after the coil has made three quarters of a turn?
Check yourself
Which change makes the peak e.m.f. of a generator larger but leaves its frequency the same?
Check yourself
The e.m.f. from a simple generator has a period of 0.025 s0.025\ \text{s}. How many turns does the coil make each second?

Common mistakes

  • Thinking slip rings cause the alternating current or keep the coil spinning. They only keep the turning coil connected to the circuit; the a.c. comes from the coil's sides reversing their motion.
  • Thinking the e.m.f. is largest when the coil is at right angles to the field. It is zero there, because the sides move along the field lines; it is largest when the coil is parallel to the field.
  • Counting the labelled points on a graph instead of fractions of a cycle. Each quarter of a cycle is a quarter turn, whatever letters mark the points.
  • Giving changes outside the generator, such as a brighter lamp, when asked how to increase the e.m.f. Change the generator: faster turning, a stronger magnet or more turns on the coil.
  • Saying faster turning only raises the frequency. The sides cut field lines faster too, so the peaks get taller as well.

Exam tips

  • "Describe" how an a.c. generator works as separate points: the coil turns in a magnetic field, its sides cut field lines, an e.m.f. is induced, and it reverses every half turn.
  • "Explain" the job of slip rings and brushes: they keep a continuous connection between the turning coil and the circuit, without the wires twisting.
  • Asked how to increase a generator's output, "state" separate changes to the generator, each with a direction word: turn the coil faster, use a stronger magnet, or put more turns on the coil.

Key takeaways

Learn thisRotating-coil a.c. generator: the coil turns in a magnetic field, its sides cut field lines, and the induced e.m.f. reverses every half turn.
Learn thisSlip rings turn with the coil, and fixed brushes press on them. They connect the turning coil to the circuit without the wires twisting; they do not make the current alternate.
Learn thisRotating-magnet generator: the field through a fixed coil reverses every half turn of the magnet, giving an alternating e.m.f. The coil doesn't move, so no slip rings are needed.
Learn thisRotating coil: the e.m.f. is zero when the plane of the coil is at right angles to the field lines, and is a peak or trough when it is parallel to them.
Learn thisIn a simple generator (one coil, two poles), one turn of the coil gives one cycle of e.m.f., so the frequency equals the number of turns each second.
Learn thisWith everything else kept the same: faster turning gives taller peaks and a higher frequency; a stronger magnet or more turns on the coil gives taller peaks at the same frequency.

Practise this

11 past-paper questions on The a.c. generator in the 0625 Extended bank, each with a mark scheme and a worked explanation.

Practise The a.c. generator →