The d.c. motor
In a minute
A coil carrying a current in a has forces in opposite directions on its two sides, so it can turn. More turns, a bigger current or a stronger field give a bigger turning effect. A uses this; Extended students also learn how its commutator and brushes keep it turning one way.
You'll be able to
- Explain why a coil carrying a current in a magnetic field turns, and in which position it does not.
- Name the three changes that make the turning effect on the coil bigger.
- Describe how a d.c. motor works, including what the and the brushes do.
Before you start3 quick questions on what this builds on
Revise first: 1.5.2 Turning effect of forces, 4.1 Simple phenomena of magnetism, 4.2.2 Electric current and 4.5.4 Force on a current-carrying conductor
Why a coil turns
In 4.5.4 a single wire carrying a current across a field felt a push: the . Now bend the wire into a flat loop, a coil, and mount it on an axle between the poles of a .
The current goes along one side of the coil and comes back along the other. So the two sides carry current in opposite directions. The forces on them are opposite too: one side is pushed up and the other is pushed down.
These two forces both have a about the axle, in the same sense. So together they give a turning effect, and the coil rotates.
Diagrams often show the coil end-on, looking along the axle. A cross (×) means current into the page; a dot (•) means current out of the page.
The turning effect is biggest when the plane of the coil lies along the field lines. After a quarter turn the coil lies across the field lines. The forces still act, but along a line through the axle, so their moment is zero.
So a coil on its own turns until it lies across the field, swings past a little, and settles there. A real motor has an extra part that keeps it turning the same way past this position.
A is built around this coil. Its turning effect spins the axle, which can drive a fan, a pump or the wheels of a toy car.
Three changes make the turning effect bigger:
1. More turns of wire on the coil. Each turn feels its own pair of forces, so the forces add up.
2. A bigger current in the coil. The force on each side is bigger.
3. A stronger , from stronger magnets or from poles moved closer to the coil. Again the force on each side is bigger.
Reversing the current, or swapping the poles of the magnet, makes the coil turn the other way; doing both at once cancels out. Neither change makes the turning effect bigger.
Try it first, then reveal one step at a time.
- Three things set the turning effect: how many turns the coil has, the size of the current and how strong the field is.
- Give one change for each, and say which way to change it.
- He could wind more turns of wire on the coil. He could increase the current in the coil, for example by adding a second cell in series. He could use stronger magnets, or move them closer to the coil, to make the magnetic field stronger.
Try it first, then reveal one step at a time.
- Compare the currents in the two sides, then the forces.
- Ask whether the forces have a moment about the axle in each position.
- The current flows in opposite directions along the two sides of the coil. So the forces on the two sides act in opposite directions, one up and one down. Both forces have a moment about the axle in the same sense, so the coil turns. When the plane of the coil is at right angles to the field lines, the forces act along a line through the axle. Then they have no moment, so there is no turning effect and the coil settles in that position.
How a d.c. motor keeps turning Extended only
A coil on its own stops once it lies across the field. To keep it turning one way, the coil's current must change direction once every half turn, just as it passes that position. A does this.
Two brushes, usually blocks of carbon, are fixed in place and press on the ring. Wires join them to the d.c. supply. The ring turns with the coil while the brushes stay still.
1. Current enters through one brush, goes round the coil and leaves through the other brush. The opposite forces on the two sides turn the coil.
2. As the coil reaches the position across the field, the gaps in the ring pass the brushes. The turning effect is zero for an instant, but the moving coil carries on past.
3. Each brush now touches the other half of the ring, so the current in the coil reverses.
4. So whichever side is next to the N pole always carries current the same way. The force on it is always the same way, and the coil keeps turning in one direction.
The brushes slide on the turning ring. They keep the coil connected to the supply without the wires twisting up.
An uses two instead, which never swap connections. A d.c. motor fitted with slip rings would only rock to and fro.
Try it first, then reveal one step at a time.
- Start with why the coil turns: the currents and forces in its two sides.
- Then say when and why the current must reverse, and which part reverses it.
- Finish with the brushes.
- The current flows in opposite directions in the two sides of the coil. So the forces on the two sides act in opposite directions, and they give a turning effect about the axle. The split-ring commutator reverses the coil's current every half turn, as the coil passes the position at right angles to the field. So the turning effect always acts in the same direction, and the coil keeps turning one way. The brushes press on the turning commutator and keep the coil connected to the battery without the wires twisting.
Try it first, then reveal one step at a time.
- Field: from N to S, so to the right.
- Left side: current into the page. Left hand: first finger to the right, second finger into the page. The thumb points down.
- Right side: current out of the page, so the force is the other way: up.
- Left side down and right side up: picture a clock face to see the sense of rotation.
- The field runs from N to S, to the right. The current in the left side flows into the page, so the gives a downward force on that side. The current in the right side flows out of the page, so the force on it is upward. With the left side pushed down and the right side pushed up, the coil turns anticlockwise as seen from the commutator end.
Common mistakes
- Picking a pair of changes where one increases and the other decreases. The result is uncertain; only changes that are all increases must increase the turning effect.
- Thinking the forces vanish when the coil lies across the field. They still act, but along a line through the axle, so they have no moment.
- Listing "reverse the current" as a way to increase the turning effect. Reversing changes only the direction of turning.
- Extended: saying the commutator makes the motor faster. Its job is to reverse the coil's current at each half turn, which keeps the rotation in one direction.
- Extended: giving a direction of turning without stating the field and current directions that give it.
- Extended: mixing up the parts: a d.c. motor has a split-ring commutator, and an a.c. generator has slip rings.
Exam tips
- When you "state" how to increase the turning effect, give the direction of each change: "more turns", "a bigger current", "a stronger magnetic field". "Change the current" earns no mark.
- Extended: to "describe" how a motor works, write one point per sentence: opposite forces on the two sides, a turning effect, the commutator reversing the current every half turn, the coil turning one way, and the brushes keeping contact.
- In a Paper 1/2 multiple-choice question that pairs two changes, check each change on its own. Pick the option where every change increases the turning effect.
Key takeaways
Practise this
10 past-paper questions on The d.c. motor in the 0625 Extended bank, each with a mark scheme and a worked explanation.