tells you how hard it is to push a current through a component: R=IV, measured in ohms (Ω). You find it with an and a , and a metal wire has more resistance when it is longer or thinner.
You'll be able to
Recall R=IV and use it to find a resistance, a current or a p.d.
Describe how to measure a resistance with an ammeter and a voltmeter, and work out the result from the readings.
State how the resistance of a metal wire depends on its length and its thickness.
Calculate a wire's new resistance when its length or cross-sectional area changes, using R∝l and R∝A1.
Sketch the current–voltage graph of a , a and a , and explain each shape.
Before you start3 quick questions on what this builds on
Check yourself
How is an connected to measure the current in a resistor?
Check yourself
How is a connected to measure the across a resistor?
Check yourself
An ammeter reads 250mA. What is this current in amperes?
Connect the same battery to two different components and you may get very different currents. A component that lets only a small current through for a given p.d. has a large .
Learn this
R=IV
Here R is the resistance in Ω, V is the p.d. across the component in V, and I is the current in it in A. Rearranged, I=RV and V=IR.
A is a component made to have a fixed resistance. If its temperature stays the same, doubling the p.d. across it doubles the current. This is : the current is directly proportional to the p.d.
Worked exampleThe p.d. across a resistor is 4.5V and the current in it is 0.30A. Calculate its resistance.
Try it first, then reveal one step at a time.
Write the equation: R=IV.
Substitute: R=0.304.5.
R=15Ω
R=15Ω
Worked exampleA 47Ω resistor is connected across a 6.0V supply. Calculate the current in the resistor.
Try it first, then reveal one step at a time.
Rearrange R=IV to get I=RV.
Substitute: I=476.0=0.1276…A.
The data have 2 significant figures, so give 0.13A.
I≈0.13A
Check yourself
The p.d. across a component is 2.0V and the current in it is 40mA. What is its resistance?
Check yourself
The current in an 18Ω resistor is 0.25A. What is the p.d. across it, in V?
Measuring resistance with meters
You can't read a resistance straight off a meter in this experiment. Instead you measure the current and the p.d., then calculate R=IV.
The lets you change the current to get several readings.
1. Connect the resistor in series with the battery, an and a variable resistor. Connect a in parallel across the resistor only.
2. Record the current I from the ammeter and the p.d. V from the voltmeter. Adjust the variable resistor and record at least four more pairs of readings.
3. Calculate R=IV for each pair and take the mean. Or plot V against I: if the points lie on a straight line through the origin, its is the resistance.
Worked exampleDescribe how you would find the resistance of a resistor using an ammeter and a voltmeter.
Try it first, then reveal one step at a time.
Say where each meter goes.
Say what you read and how you change it.
Finish with the calculation.
Connect the resistor in series with a battery, a variable resistor and an ammeter. Connect a voltmeter in parallel across the resistor. Read the current from the ammeter and the p.d. from the voltmeter. Adjust the variable resistor to get several pairs of readings. Calculate R=IV for each pair and take the mean.
Worked exampleA student's readings for a resistor are 1.5V with 0.32A, 3.0V with 0.61A, and 4.5V with 0.95A. Calculate the mean resistance.
Try it first, then reveal one step at a time.
Use R=IV for each pair: 0.321.5=4.69Ω, 0.613.0=4.92Ω, 0.954.5=4.74Ω.
Mean: 34.69+4.92+4.74=4.78Ω.
The readings have 2 significant figures, so give 4.8Ω.
R≈4.8Ω
Check yourself
Why is a variable resistor included in the circuit for measuring resistance?
Check yourself
In this experiment the voltmeter reads 2.6V and the ammeter reads 0.20A. What is the resistance, in Ω?
Length and thickness of a wire
Metals are good , but a metal wire still has some resistance. Compare wires of the same metal at the same temperature.
These are the . The cross-sectional area is the area of the end you would see if you cut straight across the wire.
Worked exampleA metal wire in a circuit is replaced by a longer, thinner wire made of the same metal. The battery stays the same. State what happens to the resistance and to the current.
Try it first, then reveal one step at a time.
Think about the length and the thickness separately.
Then use I=RV for the current.
The resistance increases. A longer wire has more resistance, and a thinner wire also has more resistance. The current decreases, because the p.d. is the same and the resistance is larger.
Check yourself
Four wires are made of the same metal. Which one has the greatest resistance?
Extended only
Extended students use the exact rules. For wires of the same metal at the same temperature, resistance is directly proportional to length l when the area is the same. It is inversely proportional to cross-sectional area A when the length is the same.
Extended only
Learn this
R∝lR∝A1
Extended only
So doubling the length doubles R, and doubling the area halves R. A round wire's area depends on its diameter squared, so doubling the diameter makes the area 4 times bigger and R a quarter.
Extended only
Worked exampleA 2.5m length of constantan wire has a resistance of 9.0Ω. Calculate the resistance of 0.80m of the same wire.
Try it first, then reveal one step at a time.
Same metal and same area, so R∝l.
The length is multiplied by 2.50.80, so the resistance is too.
R=9.0×2.50.80=2.88Ω, which is 2.9Ω to 2 significant figures.
R≈2.9Ω
Extended only
Worked exampleTwo copper wires have the same length. Wire P has a cross-sectional area of 0.50mm2 and a resistance of 0.68Ω. Wire Q has a cross-sectional area of 0.20mm2. Calculate the resistance of wire Q.
Try it first, then reveal one step at a time.
Same metal and same length, so R∝A1: a smaller area gives a larger resistance.
The area is divided by 0.200.50=2.5, so the resistance is multiplied by 2.5.
R=0.68×2.5=1.7Ω
R=1.7Ω
Extended only
Check yourself
A metal wire has a resistance of 12Ω. A wire of the same metal and the same length has twice the diameter. What is its resistance, in Ω?
Extended only
Check yourself
A wire is replaced by one of the same metal with twice the length and twice the cross-sectional area. What happens to the resistance?
Current–voltage graphs Extended only
A current–voltage graph shows how the current I in a component changes as the p.d. V across it changes. Negative values mean the component is connected the other way round.
Each graph passes through the origin: no p.d., no current.
With I up the side, a steeper straight line through the origin means a smaller resistance. On a curve, find the resistance at a point from that point's values: R=IV. Don't use the gradient of the curve.
Worked exampleExplain why the current–voltage graph for a filament lamp is a curve, not a straight line.
Try it first, then reveal one step at a time.
Start with what a bigger current does to the filament.
Link the temperature to the resistance.
Finish with the effect on the graph.
As the p.d. increases, the current increases. The filament gets hotter. So the filament's resistance increases. So the current increases less for each extra volt, and the graph gets less steep.
Check yourself
A diode is connected the wrong way round (in reverse) to a battery. What is the current?
Check yourself
A point on a filament lamp's I–V graph shows a p.d. of 6.0V and a current of 0.40A. What is the lamp's resistance at this point, in Ω?
Common mistakes
Calculating VI or V×I. Resistance is R=IV: p.d. divided by current.
Leaving a current in mA. Change it to A before using R=IV, or the resistance comes out 1000 times too small.
Using the battery's p.d. for one component in a circuit with others. Use the p.d. across that component.
Connecting the voltmeter in series with the resistor. It goes in parallel, across the resistor only.
Thinking a thinner wire has less resistance. For the same metal and length, thinner means less room for the charge, so more resistance.
Extended: halving the resistance when a wire's diameter doubles. The area is 4 times bigger, so the resistance is a quarter.
Exam tips
"Calculate" a resistance: write R=IV, then the numbers, then the answer with the unit Ω.
"Describe" the experiment: say where each meter goes, what you vary, what you read and how you calculate R. Each of these can earn a mark.
"State" how length or thickness affects resistance: give the direction (more or less resistance), not just "it changes".
Extended: a Paper 2/4 question may give a wire's diameter, not its area. Square the change in diameter to get the change in area.
Key takeaways
Learn thisR=IV(resistance in Ω)
Learn thisA resistor at constant temperature has a constant resistance: the current in it is directly proportional to the p.d. (Ohm's law).
Learn thisTo measure resistance: ammeter in series, voltmeter in parallel across the resistor, a variable resistor to get several readings; calculate R=IV for each and take the mean.
Learn thisWires of the same metal at the same temperature: longer means more resistance (same thickness); thicker means less resistance (same length).
Learn thisR∝l(same area)R∝A1(same length)
Learn thisI–V graphs (I on the vertical axis): resistor at constant temperature, straight line through the origin; filament lamp, curve getting less steep as the filament heats and its resistance rises; diode, almost no current in reverse, current rises steeply in the forward direction.
Practise this
63 past-paper questions on Resistance in the 0625 Extended bank, each with a mark scheme and a worked explanation.