4.5.1 · CorePaper 1Paper 2Paper 3Paper 4

Electromagnetic induction

In a minute

Move a wire across a , or change the field through a coil, and an appears in it. This is , and it is how a power-station works. Faster movement, a stronger and more turns on the coil all give a bigger e.m.f.

You'll be able to

  • Say when an e.m.f. is induced: a conductor cutting across field lines, or a changing magnetic field through a coil.
  • Describe an experiment that shows electromagnetic induction, and what the meter shows.
  • State the factors that make an induced e.m.f. bigger.
  • Use : the induced e.m.f. opposes the change that causes it.
  • Use Fleming's right-hand rule to link the directions of motion, field and induced current, and find the force on the induced current.
Before you start2 quick questions on what this builds on
Check yourself
Outside a bar magnet, which way do the magnetic field lines point?
Check yourself
Which statement describes an ?

Revise first: 1.7.3 Energy resources, 4.1 Simple phenomena of magnetism, 4.2.2 Electric current and 4.2.3 Electromotive force and potential difference

Inducing an e.m.f.

A sitting still beside a wire does nothing to it. But move the wire across the magnet's , and an appears between the ends of the wire.

There are two ways to cause :

1. Move a conductor so that it cuts across . Only relative movement counts: moving the magnet past a still wire works just as well.

2. Change the magnetic field that passes through a coil, even with nothing moving. Switching an electromagnet on or off next to a coil does this.

No cutting of field lines and no change in the field means no e.m.f. A wire that moves along the field lines, parallel to them, cuts none, so nothing is induced.

The e.m.f. is induced even if the ends of the wire are not joined. If the conductor is part of a complete circuit, the e.m.f. drives an induced current round it.

To show induction, use a bar magnet, a coil of wire and a sensitive centre-zero meter. Its needle rests in the middle of the scale and can swing either way.

1. Connect the ends of the coil to the meter, so the coil is part of a complete circuit.

2. Push the N pole of the magnet into the coil. The needle flicks one way while the magnet moves.

3. Hold the magnet still inside the coil. The needle goes back to zero.

4. Pull the magnet out. The needle flicks the other way. Moving the coil instead of the magnet gives the same results.

A bar magnet on the left, with its S pole at the left end and its N pole at the right end, facing a coil of wire on the right. A double-headed arrow above the magnet is labelled move the magnet in and out. The two ends of the coil are joined by wires to a sensitive centre-zero meter below the coil, making a complete circuit. The meter's needle rests at zero in the middle of its scale and can swing either way. A note says the needle moves only while the magnet moves, one way for in and the other way for out. S N bar magnet move the magnet in and out coil of wire 0 sensitive centre-zero meter The needle moves only while the magnet moves: one way for in, the other way for out.
Demonstrating electromagnetic induction with a magnet, a coil and a centre-zero meter.

Reverse either the movement or the magnet, and the needle swings the opposite way. Reverse both, and the two changes cancel: the needle swings the original way.

Move the magnet in and out again and again, and you get an . A power-station uses the same idea, with a magnet or coil that keeps turning.

Worked exampleAmira has a U-shaped magnet, a length of copper wire and a sensitive centre-zero ammeter. Describe how she could use them to show electromagnetic induction, and what she would see.

Try it first, then reveal one step at a time.

  1. First make a complete circuit, so an induced current can flow.
Check yourself
A coil is connected to a sensitive meter. Which of these does NOT induce an e.m.f. in the coil?
Worked exampleTwo coils are wound on the same iron ring. Coil P is connected to a battery and a switch. Coil Q is connected to a sensitive centre-zero meter. Describe and explain what the meter shows when the switch is closed, while it stays closed, and when it is opened again.

Try it first, then reveal one step at a time.

  1. Nothing moves here, so look for when the magnetic field through Q changes.
Check yourself
Pushing the N pole of a magnet into a coil makes a meter needle swing to the right. Next, the S pole of the magnet is pulled out of the same end of the coil. Which way does the needle swing?

How big is the induced e.m.f.?

The induced e.m.f. is bigger when field lines are cut faster, or when the field through a coil changes faster. So, with everything else kept the same, three changes make it bigger:

1. Move the magnet or the wire faster.

2. Use a stronger magnet.

3. Use a coil with more turns of wire. An e.m.f. is induced in each turn, and the turns add up.

Reversing the movement at the same speed, or turning the magnet round, changes the direction of the e.m.f. but not its size.

Worked exampleA student investigates how the number of turns on a coil affects the induced e.m.f. She lets a bar magnet fall through each coil and records the largest reading on a sensitive voltmeter. (a) Name the independent and dependent variables. (b) State two variables she must keep the same. (c) Explain why letting the magnet fall from the same height is better than pushing it through by hand.

Try it first, then reveal one step at a time.

  1. The independent variable is the one she changes; the dependent variable is the one she measures.
Check yourself
Pushing a magnet into a coil induces a small e.m.f. Which change would NOT make the e.m.f. bigger?

Lenz's law: the direction of the e.m.f. Extended only

Which way does an induced current flow? answers this: the induced e.m.f. always acts in the direction that opposes the change causing it.

Push the N pole of a magnet towards a coil in a complete circuit. The induced current turns the coil into an electromagnet. The end facing the magnet becomes an N pole, which repels the approaching N pole.

Pull the magnet away, and the current reverses. That end of the coil becomes an S pole, which attracts the N pole and tries to hold it back.

Two diagrams, one above the other. Each shows a bar magnet on the left, with its N pole facing the left end of a coil on the right; a wire below the coil joins its two ends, making a complete circuit. Top: an arrow shows the magnet moving towards the coil. The left end of the coil, nearest the magnet, is labelled N and its right end S. A note says the near end becomes an N pole and repels the approaching N pole. Bottom: an arrow shows the magnet moving away from the coil. Now the left end of the coil is labelled S and its right end N. A note says the near end becomes an S pole and attracts the leaving N pole. Both notes say the coil opposes the change. Magnet moves in S N moving towards the coil N S Near end becomes an N pole. It repels the approaching N pole: the coil opposes the change. Magnet moves out S N moving away from the coil S N Near end becomes an S pole. It attracts the leaving N pole: the coil opposes the change.
The coil always opposes the movement of the magnet.

So you must do work to move the magnet in or out. That work becomes the electrical energy of the induced current.

Worked exampleThe S pole of a bar magnet is pulled away from one end of a coil that is connected to a lamp. State the pole induced at that end of the coil, and explain your answer using Lenz's law.

Try it first, then reveal one step at a time.

  1. Name the change: the S pole is moving away.
Check yourself
The S pole of a magnet is pushed towards one end of a coil in a complete circuit. What happens at that end of the coil?

Directions of motion, field and induced current Extended only

For a straight wire moving through a field, Fleming's right-hand rule gives the direction of the induced current. Hold the thumb and first two fingers of your right hand at right angles to each other.

Thumb: the motion of the wire. First finger: the field, from N to S. Second finger: the induced current, as conventional current.

The rule is used when the wire, its motion and the field are all at right angles to each other, as in exam diagrams. A cross (×) on a wire drawn end-on means current into the page; a dot (•) means current out of the page.

The induced current is in a magnetic field, so it feels a force. Lenz's law tells you its direction: it always acts against the motion. The gives the same direction.

An N pole at the top and an S pole at the bottom, with magnetic field lines running straight down between them, from N to S. A straight wire passes through the gap at right angles to the page, drawn end-on as a small circle with a cross in it, meaning the induced current flows into the page. A thick arrow pointing right from the wire is labelled motion. A thick arrow pointing left from the wire is labelled force on the induced current, opposing the motion. Notes on the right say: field from N to S, down the page; wire moved to the right; induced current into the page; force on the wire to the left. N S motion force on the induced current Field: N to S, down the page Wire moved to the right Induced current: into the page (×) Force on wire: to the left, opposing the motion
Thumb right (motion), first finger down (field): the second finger points into the page (current).
Worked exampleThe N pole of a magnet is on the right and its S pole is on the left, so the field between them points to the left. A wire at right angles to the page is moved up through the field. Find the direction of the induced current, and the direction of the force on the wire due to this current.

Try it first, then reveal one step at a time.

  1. Field: from N to S, so to the left. Motion: up the page.
Worked exampleA straight wire lies across the page from left to right, in a magnetic field that points into the page. When the wire is moved, electrons flow along it from left to right. In which direction is the wire moving?

Try it first, then reveal one step at a time.

  1. The rule uses conventional current. Electrons flow left to right, so the conventional current flows right to left.
Check yourself
A wire lies up and down the page, in a magnetic field that points into the page. The wire is moved to the right. Which way is the induced current in the wire?
Check yourself
A wire is pushed to the left through a magnetic field, and a current is induced in it. Which way does the force from the induced current act on the wire?

Common mistakes

  • Thinking a magnet held still inside a coil induces an e.m.f. Only a change does: movement across the field, or a field that is growing or shrinking.
  • Connecting the wire to a power supply to "induce" an e.m.f. A supply drives a current and gives a force on the wire; induction needs the wire to cut field lines, or the field through a coil to change.
  • Moving the wire along the field lines, or along its own length. It cuts no field lines, so no e.m.f. is induced: move it across the field.
  • Forgetting that two reversals cancel. Using the other pole and moving the other way gives the same direction of deflection as before.

Exam tips

  • "Describe" the induction experiment in three parts: the apparatus (magnet, coil, sensitive meter in a complete circuit), what you do (move the magnet in and out), and what you see (a reading only while it moves, opposite ways for in and out).
  • "Explain" why a lamp or meter responds: link relative movement or a changing field, to an induced e.m.f., to a current in a complete circuit.

Key takeaways

Learn thisAn e.m.f. is induced in a conductor when it cuts across magnetic field lines, or when the magnetic field through it changes. No relative movement and no change in the field means no e.m.f.
Learn thisAn induced e.m.f. drives an induced current only if the conductor is part of a complete circuit.
Learn thisDemonstration: move a magnet in and out of a coil joined to a sensitive centre-zero meter. The needle deflects only while the magnet moves, opposite ways for in and out.
Learn thisWith everything else kept the same, the induced e.m.f. is bigger for faster movement, a stronger magnet or more turns on the coil. Reversing the movement (at the same speed) or the magnet reverses the e.m.f. but does not change its size.
Learn thisLenz's law: an induced e.m.f. acts in the direction that opposes the change causing it. A coil in a complete circuit repels an approaching pole and attracts a leaving one.
Learn thisFleming's right-hand rule, for a wire, motion and field all at right angles: thumb = motion, first finger = field (N to S), second finger = induced conventional current. The force on the induced current opposes the motion.

Practise this

38 past-paper questions on Electromagnetic induction in the 0625 Extended bank, each with a mark scheme and a worked explanation.

Practise Electromagnetic induction →