4.2.3 · CorePaper 1Paper 2Paper 3Paper 4Paper 5Paper 6

Electromotive force and potential difference

In a minute

A cell does work on the charge it pushes round a circuit: the work it does on each is its (e.m.f.). The charge then does work in each component: the work per coulomb there is the (p.d.). Both are measured in volts, with a connected in parallel.

You'll be able to

  • Define (e.m.f.) and know that it is measured in volts.
  • Define (p.d.), know that it is measured in volts, and tell it apart from e.m.f.
  • Use analogue and digital : connect them in parallel, choose a suitable range and read the scale.
  • Calculate e.m.f. and p.d. with E=WQE = \frac{W}{Q} and V=WQV = \frac{W}{Q}, and rearrange them.
Before you start3 quick questions on what this builds on
Check yourself
What is the unit of ?
Check yourself
What is the unit of ?
Check yourself
How is an connected to measure the current in a lamp?

Revise first: 1.7.1 Energy, 1.7.2 Work, 4.2.1 Electric charge and 4.2.2 Electric current

E.m.f. and p.d.: energy given and energy used

A cell or battery is the energy source for a circuit. It uses energy from its chemical store to push round the circuit. So the cell does on the charge.

To compare sources, we look at how much work a source does on every unit of charge. Charge is measured in (C), so this is the given to each coulomb.

E.m.f. is measured in volts (V). One volt is one joule per coulomb: 1 V=1 J/C1\ \text{V} = 1\ \text{J/C}. So a 1.5 V1.5\ \text{V} cell does 1.5 J1.5\ \text{J} of work on every coulomb it moves round the circuit.

The charge gives up this energy in the components. As charge passes through a lamp, it does work there: energy is transferred to the surroundings by light and by heating.

P.d. is also measured in volts. A p.d. of 4 V4\ \text{V} across a heater means each coulomb transfers 4 J4\ \text{J} in the heater. A p.d. is always between two points, such as the two ends of a component.

A cell and a lamp joined in a single loop. The cell is on the left side of the loop, with its positive terminal at the top. The lamp is on the right side. Arrows on the wires show the current going clockwise: out of the positive terminal, along the top wire, down through the lamp and back along the bottom wire. A label beside the cell says the cell does work on the charge, and this is the e.m.f. A label beside the lamp says the charge does work in the lamp, and this is the p.d. + − current cell does work on the charge e.m.f. lamp the charge does work here p.d.
E.m.f. belongs to the source, which gives the charge energy. P.d. belongs to a component, where the charge gives energy up.

Despite its name, e.m.f. is not a force. It is work done per unit charge, just like p.d. People often call both of them "voltage", but use e.m.f. or p.d. in the exam.

Worked exampleA rechargeable cell has an e.m.f. of 1.2 V1.2\ \text{V}. Explain what this means.

Try it first, then reveal one step at a time.

  1. Recall what e.m.f. is: the work a source does on each unit of charge it moves round the circuit.
Worked exampleState one way in which e.m.f. and p.d. are the same, and one way in which they are different.

Try it first, then reveal one step at a time.

  1. Same: look at the unit, and at what kind of quantity each one is.
Check yourself
A battery is labelled 9 V. What does the 9 V tell you about the battery?
Check yourself
A student finds the energy that each coulomb of charge transfers as it passes through a motor. Which quantity has she found?

Measuring p.d. with a voltmeter

A measures p.d. in volts. Connect it in parallel: one lead to each end of the component. You don't break the circuit to add it. Its circuit symbol is a circle with the letter V.

A voltmeter has a very high resistance. Almost no current passes through it, so it hardly changes the circuit it measures.

A voltmeter connected across the terminals of a cell or battery, with nothing else connected to it, measures its e.m.f. So a voltmeter is all you need to measure an e.m.f.

Join the meter's + terminal (often red) to the side nearer the + terminal of the supply. Connected the other way round, an analogue pointer tries to move below zero and a digital meter shows a minus sign.

A digital voltmeter shows the p.d. as a number and often has several ranges, such as 200 mV, 2 V and 20 V. Choose the smallest range that is bigger than the p.d. you expect: it gives the most decimal places. If you can't estimate the p.d., start on the largest range and switch down.

Many analogue voltmeters have two ranges, such as 0–3 V and 0–15 V. Each range has its own terminal and its own scale. Read the scale that matches the terminal you used.

Read an analogue scale as in 4.2.2: work out what one small division is worth, and read to the nearest half division. Look straight at the pointer, and check it starts at zero.

The scale of an analogue voltmeter, marked V, with two scales on one arc. The upper scale runs from 0 to 15 with labels at 0, 5, 10 and 15. The lower scale runs from 0 to 3 with labels at 0, 1, 2 and 3. There are ten small divisions between each pair of labels. Three terminals at the bottom are marked minus, 3 V and 15 V. The pointer lies on the fourth small mark after the label 2 on the lower scale, which is the same as the fourth small mark after 10 on the upper scale. 0 0 5 1 10 2 15 3 V 0–15 V scale 0–3 V scale − 3 V 15 V
A two-range analogue voltmeter. The 3 V terminal uses the lower scale; the 15 V terminal uses the upper scale.
Worked exampleThe voltmeter in the figure is connected with its − and 3 V terminals. State the p.d. it shows.

Try it first, then reveal one step at a time.

  1. The 3 V terminal is in use, so read the lower scale, which runs from 0 to 3.
Worked exampleA student wants to measure the e.m.f. of a battery labelled 4.5 V with the voltmeter in the figure. Should she use the 3 V terminal or the 15 V terminal? Explain your choice.

Try it first, then reveal one step at a time.

  1. Compare the expected value with each range: 4.5 V4.5\ \text{V} is more than 3 V3\ \text{V} but less than 15 V15\ \text{V}.
Check yourself
Which meter measures the p.d. across a resistor, and how is it connected?
Check yourself
A digital voltmeter on its 200 mV range shows 148.0. What is the p.d. in volts?

Calculating e.m.f. and p.d. Extended only

E.m.f. and p.d. are both work done divided by charge. Each has its own equation, and you need to recall both.

Learn this
E=WQE = \frac{W}{Q}
Learn this
V=WQV = \frac{W}{Q}

Here EE is the e.m.f. and VV is the p.d., both in volts (V). WW is the work done (the energy transferred) in joules (J), and QQ is the charge in coulombs (C).

Both rearrange the same way: W=EQW = EQ or W=VQW = VQ, and Q=WEQ = \frac{W}{E} or Q=WVQ = \frac{W}{V}. If a question gives a current and a time instead of a charge, find the charge first with Q=ItQ = It (4.2.2).

Worked exampleA 12 V12\ \text{V} car battery drives 450 C450\ \text{C} of charge round the circuit of its starter motor. Calculate the work done by the battery.

Try it first, then reveal one step at a time.

  1. The battery is the source, so use the e.m.f. equation: E=WQE = \frac{W}{Q}.
Worked exampleA lamp carries a current of 0.80 A0.80\ \text{A} for 1.51.5 minutes. In that time, the charge passing through it transfers 432 J432\ \text{J} of energy. Calculate the p.d. across the lamp.

Try it first, then reveal one step at a time.

  1. Convert the time to seconds: 1.5×60=90 s1.5 \times 60 = 90\ \text{s}.
Check yourself
A 9.0 V9.0\ \text{V} battery does 315 J315\ \text{J} of work. How much charge has it moved round the circuit?
Check yourself
As 25 C25\ \text{C} of charge passes through a resistor, it transfers 150 J150\ \text{J} of energy. What is the p.d. across the resistor, in V?

Common mistakes

  • Choosing p.d. when the question describes e.m.f., or the other way round, because both are in volts. E.m.f. is work done by a source on the charge; p.d. is work done by the charge in a component.
  • Thinking e.m.f. is a force because of its name. It is work done per unit charge, measured in volts.
  • Connecting a voltmeter in series. It goes in parallel, with one lead on each side of the component.
  • Reading the wrong scale on a two-range analogue voltmeter. Use the scale that matches the terminal in use.
  • Extended: writing units such as JC\frac{\text{J}}{\text{C}} when asked for the equation. Write the quantities: E=WQE = \frac{W}{Q}, work done divided by charge.
  • Extended: dividing energy by current or time, or charge by energy. Find the charge in coulombs, then divide the work done by it.

Exam tips

  • "Define" e.m.f.: say it is the electrical work that a source does on each unit of charge, and include "round a complete circuit". Just writing "the voltage of a cell" earns nothing.
  • "Define" p.d.: say it is the work done per unit charge passing through a component. Naming the component is what makes it p.d. and not e.m.f.
  • "Calculate" with E=WQE = \frac{W}{Q} or V=WQV = \frac{W}{Q} (Extended): write the equation, substitute joules and coulombs, then give the answer in volts.

Key takeaways

Learn thisE.m.f.: the electrical work a source does on each unit of charge it moves round a complete circuit. Measured in volts (V).
Learn thisP.d.: the work done by each unit of charge as it passes through a component. Measured in volts (V), between two points. 1 V=1 J/C1\ \text{V} = 1\ \text{J/C}.
Learn thisA voltmeter measures p.d. (or e.m.f.) and is connected in parallel. Choose the smallest range bigger than the expected p.d., and read the scale that matches the terminal used.
Learn thisE=WQE = \frac{W}{Q}
Learn thisV=WQV = \frac{W}{Q}

Practise this

19 past-paper questions on Electromotive force and potential difference in the 0625 Extended bank, each with a mark scheme and a worked explanation.

Practise Electromotive force and potential difference →