7.3 · CorePaper 5Paper 6

Taking and recording measurements

In a minute

Paper 5 and Paper 6 give easy marks for readings done well: the right number of figures, a corrected, values that make sense, enough repeats, and a tidy table with units. This lesson shows you how to earn each of those marks.

You'll be able to

  • Read analogue and digital instruments, or diagrams of them, to the right , including to the nearest half division.
  • Correct a reading for a zero error, and check that every reading or estimate is sensible.
  • Take enough readings, over a wide range, and repeat them when they vary.
  • Record what you see in words, and record measurements in a clear table with units.
Before you start3 quick questions on what this builds on
Check yourself
How is an connected to measure the current in a lamp?
Check yourself
What does it mean when a measurement is accurate?
Check yourself
A student changes the mass on a spring and measures how far it stretches. Which is the ?

Revise first: 4.2.2 Electric current, 4.2.3 Electromotive force and potential difference, 4.3.1 Circuit diagrams and circuit components, 7.1 Apparatus, techniques and safety and 7.2 Planning investigations

Reading analogue and digital instruments

An analogue instrument has a scale and a pointer or a liquid thread, like a ruler, a thermometer or a meter with a needle. A digital instrument shows the number for you. Paper 6 shows the same scales in diagrams: read them the same way.

On an analogue scale, first work out what one small division is worth. Divide the gap between two labels by the number of small divisions between them.

Read with your eye level with the pointer or liquid, looking at right angles to the scale. This avoids parallax error.

When the divisions are wide enough, judge the halfway point. A thermometer marked every 1 °C1\ \text{°C} can be read to 0.5 °C0.5\ \text{°C}. On a ruler marked in mm, read to the nearest mm.

Close-up of a liquid-in-glass thermometer lying on its side, with the bulb on the left. The scale above the tube is marked every 1 degree Celsius from 20 to 30, with numbers only at 20, 25 and 30. The liquid thread runs from the bulb and ends exactly halfway between the 26 and 27 marks. 20 25 30 °C end of the liquid thread
A thermometer scale marked every 1 °C1\ \text{°C}.
Worked exampleRead the temperature shown by the thermometer in the figure.

Try it first, then reveal one step at a time.

  1. The gap from 20 to 25 has 5 small divisions, so each one is worth 1 °C1\ \text{°C}.

A digital display: write down every digit it shows, including a final zero. A balance showing 48.70 g is recorded as 48.70 g, not 48.7 g.

Recording to the right means giving the reading to the smallest step you can read: every digit of a digital display, or the nearest division (or half division) of an analogue scale. No more figures, and no fewer. If a digital reading flickers, wait for it to settle, or record the value it shows most often.

Worked exampleA digital set to its milliampere range shows 360. The results table has the heading II / A. What should the student write in the table?

Try it first, then reveal one step at a time.

  1. The meter reads in mA, and 1 A=1000 mA1\ \text{A} = 1000\ \text{mA}.
Check yourself
An analogue ammeter has labels at 0, 0.5 and 1.0 A, with 5 small divisions between each pair of labels. The needle is 3 small divisions past 0.5. What is the current, in A?

Zero errors and sensible values

Before you measure anything, look at the instrument with nothing to measure. A newton meter with no load, or a meter with no current, should read zero.

A zero error shifts every reading by the same amount. Correct each reading like this: true value = reading − zero reading.

If the zero reading is below zero, subtracting it adds. A needle resting at −0.1 V-0.1\ \text{V} makes every reading 0.1 V0.1\ \text{V} too small.

Worked exampleA newton meter reads 0.3 N0.3\ \text{N} with nothing hanging on it. With a stone hanging from it, the meter reads 4.7 N4.7\ \text{N}. Calculate the weight of the stone.

Try it first, then reveal one step at a time.

  1. The meter reads 0.3 N0.3\ \text{N} when it should read zero, so every reading is 0.3 N0.3\ \text{N} too big.

A ruler with a worn end works the same way. Line the object up with a clear mark, such as 1.0 cm, and subtract that mark from the other reading.

Check yourself
A voltmeter's needle rests at −0.2 V-0.2\ \text{V} when it is not connected. In a circuit it reads 2.6 V2.6\ \text{V}. What is the true p.d., in V?

Every reading should also make sense. Before you record it, ask: is this about what I expected? A lab is usually around 20–25 °C, and a 100 g mass should read close to 100 g. Estimates should be realistic too: a door is about 2 m high.

If a value looks wrong, check the units, the scale and the connections, then measure again. Never change a reading just to match what you expected.

Worked exampleA student measures the current in a small torch lamp, powered by two cells, and records 45 A45\ \text{A}. Explain why this value is not sensible, and suggest what has gone wrong.

Try it first, then reveal one step at a time.

  1. Compare the value with what you expect for a small lamp and two cells.
Check yourself
A reading is very different from the value a student expected. What should she do first?

Enough readings, and repeats

One reading can hide a slip. To trust a pattern, take readings for at least five values of the , spread evenly over as wide a range as the apparatus allows.

Repeat a reading when repeats could differ, such as hand timing or a meter that flickers. Then calculate the mean. Repeats also show up a slip, because one reading won't match the others.

You won't be asked to recite these two definitions. You will be expected to use the ideas, for example "repeat and calculate a mean".

A results table with four columns. The headings are: number of blocks N; t1 / s; t2 / s; mean t / s. For 1 block the times are 2.84 and 2.90 seconds, mean 2.87. For 2 blocks: 2.07 and 2.01, mean 2.04. For 3 blocks: 1.72 and 1.66, with the mean left as a question mark. For 4 blocks: 1.47 and 1.51, mean 1.49. For 5 blocks: 1.33 and 1.29, mean 1.31. number of blocks N t1 / s t2 / s mean t / s 1 2.84 2.90 2.87 2 2.07 2.01 2.04 3 1.72 1.66 ? 4 1.47 1.51 1.49 5 1.33 1.29 1.31
A toy car rolls down a ramp raised by NN wooden blocks. Each time is measured twice.
Worked exampleCalculate the missing mean time in the table for 3 blocks.

Try it first, then reveal one step at a time.

  1. Add the two times and divide by 2: 1.72+1.662=3.382=1.69\frac{1.72 + 1.66}{2} = \frac{3.38}{2} = 1.69.
Worked exampleA student plans to measure the current in a wire at p.d.s of 1.0 V1.0\ \text{V} and 1.5 V1.5\ \text{V} only, once each. Suggest two ways to make her results more reliable.

Try it first, then reveal one step at a time.

  1. Two values can't show a pattern, so think about how many values and how wide a range.
Check yourself
A student finds the density of a stone by displacement. A friend measures the same stone in a different way and gets nearly the same value. What does this show about the result?

Recording observations and tables

Some tests give no number. A qualitative observation describes what you see or hear: a lamp glows more brightly, a compass needle swings, or light does or doesn't pass through a material.

Record these in a few clear words for each test, such as "lamp lights, dim" or "no light passes through". "It changed" says nothing.

Check yourself
Which of these is a qualitative observation?

Record measurements in a table as you take them. Look at the table in the figure above: it follows four rules.

1. One column for each quantity, and one for each repeat. The independent variable goes in the first column, then the readings, then calculated values such as the mean.

2. Each heading is quantity / unit, such as tt / s or II / A. Units go in the heading only, not after every number. A count, such as the number of blocks NN, has no unit.

3. Every reading in a column has the same number of decimal places, set by the instrument. Lengths read to the nearest mm are written 12.0 cm, not 12 cm.

4. A mean keeps the decimal places of its readings. Other calculated values, such as a resistance, usually have 2 or 3 significant figures, no more than the least precise reading.

Worked exampleA student's table has the column headings "p.d." and "current". The currents, from an ammeter that reads to 0.01 A, are written 0.2, 0.25 and 0.3. Explain two ways to improve the table.

Try it first, then reveal one step at a time.

  1. Check each heading for a quantity and a unit.
Check yourself
Which is the best column heading for current readings in a results table?

Common mistakes

  • Writing "read it carefully". Name the technique, such as eye level with the scale or the bottom of the meniscus.
  • Forgetting the zero error. Look at the instrument before you start, and subtract its zero reading from every reading.
  • Writing "repeat the readings" without "calculate a mean".
  • Leaving units out of table headings, or dropping a final zero, such as 0.3 A instead of 0.30 A from a meter that reads to 0.01 A.

Exam tips

  • "Measure": give the value to the precision of the scale, with its unit.
  • "Suggest" a way to make results reliable: say exactly what, such as "repeat and calculate a mean" or "at least five values over a wider range".
  • "Complete" a table: add the unit to each heading and keep the same decimal places down each column of readings.

Key takeaways

Learn thisAnalogue scale: value of one small division = gap between two labels ÷ number of divisions. Read to the nearest half division when the divisions are wide enough.
Learn thisDigital display: record every digit shown, including a final zero, and convert mA to A if the table needs it.
Learn thisZero error: true value = reading − zero reading. If the zero reading is negative, subtracting it adds its size.
Learn thisCheck each reading is sensible; if not, check and measure again. Never change a reading to fit.
Learn thisTo find a pattern, take at least five values of the independent variable over a wide range. Repeat readings that can vary, and calculate a mean.
Learn thisTables: headings quantity / unit, independent variable first, the same decimal places down a column of readings, set by the instrument.

Practise this

387 past-paper questions on Experimental skills and investigations in the 0625 Extended bank, each with a mark scheme and a worked explanation.

Practise Experimental skills and investigations →