4.3.3 · CorePaper 1Paper 2Paper 3Paper 4Paper 5Paper 6

Action and use of circuit components

In a minute

When the same current passes through two conductors, the one with more has the larger across it, because V=IRV = IR. That is why the components of a share the supply p.d. according to their resistances, and why a sensor such as an LDR changes the meter readings in its circuit. Extended students also use the ratio rule for a and learn how a slider gives any p.d. from zero up to the supply.

You'll be able to

  • Use V=IRV = IR to explain why, for a constant current, a conductor with more resistance has a larger p.d. across it.
  • Use R1R2=V1V2\frac{R_1}{R_2} = \frac{V_1}{V_2} to find how two in series share the supply p.d., including in sensor circuits.
  • Describe how moving the slider of a changes its output p.d.
Before you start3 quick questions on what this builds on
Check yourself
The p.d. across a resistor is 6.0 V6.0\ \text{V} and the current in it is 0.40 A0.40\ \text{A}. What is its resistance, in Ω\Omega?
Check yourself
A resistor and a lamp are connected in series with a battery. How does the current in the resistor compare with the current in the lamp?
Check yourself
The light falling on a (LDR) gets dimmer. What happens to its resistance?

Revise first: 4.2.3 Electromotive force and potential difference, 4.2.4 Resistance, 4.3.1 Circuit diagrams and circuit components and 4.3.2 Series and parallel circuits

More resistance, more p.d.

Rearrange R=VIR = \frac{V}{I} from 4.2.4 and you get V=IRV = IR. The across a conductor equals the current in it times its .

Learn this
V=IRV = IR

You meet this most in a . The same current passes through every component, so the component with the bigger resistance has the bigger p.d. across it.

Two resistors, R1 and R2, connected in series with a battery in a single loop. Voltmeter V1 is connected across R1 and voltmeter V2 is connected across R2. V V R1 R2 battery V1 V2
The same current passes through R1R_1 and R2R_2. The voltmeter across the larger resistance reads more.
Worked exampleA 22 Ω22\ \Omega resistor and a 47 Ω47\ \Omega resistor are connected in series. The current in the circuit is 0.20 A0.20\ \text{A}. Calculate the p.d. across the 47 Ω47\ \Omega resistor, and compare it with the p.d. across the 22 Ω22\ \Omega resistor.

Try it first, then reveal one step at a time.

  1. The resistors are in series, so each one carries 0.20 A0.20\ \text{A}.

The same idea explains sensor circuits. Below, an LDR is in series with a fixed resistor, and the voltmeter is across the fixed resistor.

A cell, an ammeter, a light-dependent resistor and a fixed resistor connected in series in a single loop. A voltmeter is connected across the fixed resistor only. A V cell LDR fixed resistor ammeter voltmeter
The voltmeter measures the p.d. across the fixed resistor, not the LDR.
Worked exampleThe circuit in the figure is in a room. The room gets darker. State and explain what happens to the ammeter reading and to the voltmeter reading.

Try it first, then reveal one step at a time.

  1. Start with the part that changes: an LDR's resistance increases as the light gets dimmer.
Check yourself
Resistors X and Y are in series. X has three times the resistance of Y. How does the p.d. across X compare with the p.d. across Y?
Check yourself
A 56 Ω56\ \Omega resistor is in series with a lamp. The current in the circuit is 0.25 A0.25\ \text{A}. What is the p.d. across the resistor, in V?

Sharing the supply p.d.: the potential divider Extended only

Two resistors in series across a supply form a . They share the supply p.d.: V1+V2V_1 + V_2 equals the supply p.d.

The current II is the same in both, so V1=IR1V_1 = IR_1 and V2=IR2V_2 = IR_2. Divide one by the other and II cancels.

Learn this
R1R2=V1V2\frac{R_1}{R_2} = \frac{V_1}{V_2}

So the p.d.s are in the same ratio as the resistances. The larger resistor always takes the larger share of the supply p.d.

Worked exampleResistors of 1.5 kΩ1.5\ \text{k}\Omega and 3.0 kΩ3.0\ \text{k}\Omega are connected in series across a 9.0 V9.0\ \text{V} battery. Calculate the p.d. across the 3.0 kΩ3.0\ \text{k}\Omega resistor.

Try it first, then reveal one step at a time.

  1. Use the ratio: V1V2=R1R2=1.53.0=12\frac{V_1}{V_2} = \frac{R_1}{R_2} = \frac{1.5}{3.0} = \frac{1}{2}. So V2V_2 is twice V1V_1.
Worked exampleIn a potential divider, the p.d. across a 330 Ω330\ \Omega resistor is 1.8 V1.8\ \text{V} and the p.d. across the other resistor is 4.2 V4.2\ \text{V}. Calculate the resistance of the other resistor.

Try it first, then reveal one step at a time.

  1. Write the equation: R1R2=V1V2\frac{R_1}{R_2} = \frac{V_1}{V_2}, with R1=330 ΩR_1 = 330\ \Omega, V1=1.8 VV_1 = 1.8\ \text{V} and V2=4.2 VV_2 = 4.2\ \text{V}.

A potential divider becomes a sensor circuit when one resistor is a or a . When the sensor's resistance changes, its share of the supply p.d. changes too. Remember that an NTC thermistor's resistance falls as it gets warmer.

Worked exampleA thermistor and a fixed resistor form a potential divider across a battery. An alarm switches on when the p.d. across the thermistor rises above a set value. Explain why the alarm switches on when the temperature falls.

Try it first, then reveal one step at a time.

  1. Start with the sensor: a thermistor's resistance increases as it gets colder.
Check yourself
Resistors of 10 kΩ10\ \text{k}\Omega and 20 kΩ20\ \text{k}\Omega are connected in series across a 4.5 V4.5\ \text{V} battery. What is the p.d. across the 10 kΩ10\ \text{k}\Omega resistor?
Check yourself
A thermistor and a fixed resistor form a potential divider. The output p.d. is measured across the fixed resistor. The thermistor gets warmer. What happens to the output p.d.?

The variable potential divider Extended only

A , or potentiometer, is one resistance track connected across the supply. A sliding contact, the slider, can touch the track anywhere along it.

A battery connected across the two ends, A and B, of a long resistance track. A slider presses on the track partway along. A lamp is connected between end A and the slider. A B battery resistance track slider lamp
Moving the slider from A to B raises the p.d. across the lamp from zero to the full battery p.d.

The slider splits the track into two parts in series: from A to the slider, and from the slider to B. These act as the two resistors of a potential divider. The output is the p.d. between end A and the slider.

Moving the slider towards B makes the part from A longer, so its resistance increases. That part takes a larger share of the supply p.d., so the output p.d. rises.

Compare this with a in series with a lamp. That can dim the lamp, but it can't bring the lamp's p.d. down to zero.

Worked exampleIn the circuit in the figure, the slider is moved slowly from end A to end B. Describe what happens to the lamp, and explain it using p.d.

Try it first, then reveal one step at a time.

  1. Start at end A and say what the lamp's p.d. is there.
Check yourself
Which arrangement lets the p.d. across a lamp be set to any value from zero up to the full supply p.d.?
Check yourself
A potentiometer track 60 cm60\ \text{cm} long has the same resistance along every centimetre. It is connected across a 4.5 V4.5\ \text{V} battery. A voltmeter is connected between end A and the slider, which is 40 cm40\ \text{cm} from A. Assume the voltmeter takes no current. What does it read, in V?

Common mistakes

  • Deciding a voltmeter reading before checking which component it is across. Find the voltmeter first. Across the fixed resistor, use V=IRV = IR; across the sensor, it reads the supply p.d. minus the fixed resistor's p.d.
  • Stopping at "the LDR's resistance increases". Go on to say what happens to the current and to the p.d. the question asks about.
  • Getting a sensor backwards. An NTC thermistor's resistance falls as it gets warmer, and an LDR's resistance falls as the light gets brighter.
  • Extended: turning the ratio upside down. In a potential divider the larger resistor always has the larger p.d.
  • Extended: using a variable resistor in series to take a lamp's p.d. down to zero. It can't; a variable potential divider can.

Exam tips

  • "Explain" a change in a meter reading: write the chain in order. First the resistance change, then the current, then V=IRV = IR for the fixed resistor. If the meter is across the sensor, finish with: the sensor has the rest of the supply p.d.
  • Paper 1/2 multiple choice on sensor circuits: mark which component the voltmeter is across before you look at the options.
  • "Calculate" with R1R2=V1V2\frac{R_1}{R_2} = \frac{V_1}{V_2} (Extended): write the equation, substitute, then give the answer with its unit. Check that the larger resistor has the larger p.d.

Key takeaways

Learn thisFor a constant current, the p.d. across a conductor is larger when its resistance is larger (V=IRV = IR). In series, the component with the larger resistance has the larger p.d.
Learn thisSensor in series with a fixed resistor across a fixed supply p.d.: if the sensor's resistance rises, the current falls, so the p.d. across the fixed resistor falls and the p.d. across the sensor rises.
Learn thisR1R2=V1V2(two resistors in series as a potential divider)\frac{R_1}{R_2} = \frac{V_1}{V_2} \quad \text{(two resistors in series as a potential divider)}
Learn thisVariable potential divider, output taken between one end of the track and the slider: moving the slider sets the output p.d. anywhere from zero up to the full supply p.d.

Practise this

47 past-paper questions on Action and use of circuit components in the 0625 Extended bank, each with a mark scheme and a worked explanation.

Practise Action and use of circuit components →