4.4 · CorePaper 1Paper 2Paper 3Paper 4

Electrical safety

In a minute

Mains electricity can kill by electric shock and can start fires. Mains circuits use three wires, , and , with the switch and the in the live one. Fuses and cut the current when it gets too large, and a casing is either earthed or made of an insulator.

You'll be able to

  • Name the three wires of a mains circuit and explain why the switch goes in the live wire.
  • State the hazards of damaged insulation, overheating cables, damp conditions and overloaded sockets or extension leads.
  • Explain how fuses and trip switches work, and choose a suitable fuse rating or trip switch setting.
  • Explain why a casing must be earthed or double-insulated, and why a double-insulated appliance still has a fuse.
Before you start3 quick questions on what this builds on
Check yourself
A microwave oven has a power of 690 W690\ \text{W} on a 230 V230\ \text{V} supply. What is the current in it, in A?
Check yourself
Why is the outside of a mains cable made of plastic?
Check yourself
A lamp and a heater are connected in parallel to the same supply. How does the current from the supply compare with the currents in the two appliances?

Revise first: 4.2.1 Electric charge, 4.2.2 Electric current, 4.2.4 Resistance, 4.2.5 Electrical energy and electrical power, 4.3.1 Circuit diagrams and circuit components and 4.3.2 Series and parallel circuits

Live, neutral and earth

A mains circuit has three wires. The (also called the line wire) carries the p.d. of the supply, about 230 V230\ \text{V} in many countries. The completes the circuit and stays close to 0 V0\ \text{V}.

The is a safety wire. It joins any metal casing of the appliance to the ground. In normal use it carries no current.

Mains wiring of a heater with a metal case. The live wire runs from the mains through a fuse and then a switch to the heating element inside the metal case. The neutral wire returns from the heating element to the mains. The earth wire runs from the mains to the metal case itself. live neutral earth mains fuse switch metal case earth wire joined to the case heating element fuse and switch are both in the live wire
The fuse and the switch are both in the live wire. The earth wire goes to the metal case.
Worked exampleExplain why the switch for a ceiling light must be connected in the live wire and not in the neutral wire.

Try it first, then reveal one step at a time.

  1. Say what switching off does when the switch is in the live wire.
Check yourself
An electrician wires a toaster's switch into the neutral wire by mistake. The switch is turned off. Which statement is true?
Check yourself
An appliance with a metal case is working normally. Which wire carries no current?

Hazards of mains electricity

Mains electricity has two main dangers: an electric shock, which can kill, and fire.

1. Damaged insulation: the bare live wire can be touched, giving an electric shock. The live and neutral wires may also touch each other, a short circuit, so a very large current flows and the cable can catch fire.

2. Overheating cables: a current that is too large for a cable heats it up. The plastic insulation can melt or burn, which can start a fire and leave bare wires exposed.

3. Damp conditions: water with dissolved impurities conducts. It can give the current a path from a live part through a person to the ground, causing an electric shock.

4. Overloading: plugging many appliances into one socket, an adaptor or an extension lead puts them in . The current in the plug and cable is the sum of all their currents. Too large a total current makes the plug and cable overheat, which can start a fire.

Worked exampleA 2.4 kW2.4\ \text{kW} fan heater, a 1.1 kW1.1\ \text{kW} iron and a 650 W650\ \text{W} coffee machine are all plugged into one extension lead on a 230 V230\ \text{V} supply. The lead is designed for a current of up to 13 A13\ \text{A}. Calculate the total current in the lead.

Try it first, then reveal one step at a time.

  1. The appliances are in parallel, so the current in the lead is the sum of their currents. That means you can add their powers first.
Worked exampleA student dries her hair with a mains hair dryer while standing in a wet bathroom. State the hazard and explain why it is greater in damp conditions.

Try it first, then reveal one step at a time.

  1. Name the hazard to the person first.
Check yourself
A family plugs five appliances into one multi-socket adaptor. What is the main hazard?

Fuses and trip switches

A is a short, thin wire in the live wire, often inside the plug. Its rating is the largest current it carries without melting, such as 3 A3\ \text{A}, 5 A5\ \text{A} or 13 A13\ \text{A}.

A (a circuit breaker) does the same job. It is an automatic switch in the live wire that opens when the current goes above its setting. Inside, the current passes through a coil that acts as a magnet, and a large current makes it pull the switch open.

A blown fuse must be replaced. A trip switch is simply reset, by pushing its lever back, once the fault has been fixed.

Choose a rating just above the normal current of the appliance. Too low, and it cuts the current in normal use. Too high, and a fault current may not melt it, so the cable could overheat.

Worked exampleA toaster has a power of 1.25 kW1.25\ \text{kW} on a 230 V230\ \text{V} supply. Fuses of 3 A3\ \text{A}, 5 A5\ \text{A} and 13 A13\ \text{A} are available. Which fuse should be fitted in its plug?

Try it first, then reveal one step at a time.

  1. Find the normal current: I=PV=1250230=5.43… AI = \frac{P}{V} = \frac{1250}{230} = 5.43…\ \text{A}.
Worked exampleExplain how a fuse in the plug of an electric heater protects the cable if a fault makes the current too large.

Try it first, then reveal one step at a time.

  1. Say where the fuse is and what the large current does to it.
Check yourself
A food mixer has a power of 420 W420\ \text{W} on a 230 V230\ \text{V} supply. Which fuse is most suitable?
Check yourself
An electric oven takes 6.0 kW6.0\ \text{kW} from a 230 V230\ \text{V} supply. Which trip switch setting is most suitable for its circuit?
Check yourself
What is one advantage of a trip switch over a fuse?

Earthed and double-insulated casings

Inside an appliance, a loose live wire could touch a metal casing. The casing would then be live. Anyone touching it would become a path for the current to the ground and get an electric shock.

The earth wire has a very low . If the live wire touches an earthed casing, a large current flows through the casing and the earth wire to the ground. This melts the fuse or trips the trip switch, cutting off the live wire.

Worked exampleA washing machine has a metal case connected to the earth wire. A fault makes the live wire touch the case. Explain how the earth wire and the fuse protect a person who later touches the case.

Try it first, then reveal one step at a time.

  1. Start with the path the current takes after the fault.

A appliance, such as a plastic hair dryer, has insulated wires inside a casing made of an : two layers of insulation. Its casing cannot become live, so it needs no earth wire. Its cable has just two wires: live and neutral.

Check yourself
A hair straightener is double-insulated. What protection does it need?
Check yourself
Why must the earth wire have a very low resistance?

Common mistakes

  • Thinking a fuse on its own protects you from an electric shock. It protects the wiring and the appliance from too large a current; a shock can happen at a current far too small to melt it.
  • Putting the switch in the neutral wire. The appliance goes off but stays connected to the live wire, so touching it can still give a shock.
  • Thinking a double-insulated appliance needs no fuse. It needs no earth wire, but the fuse still protects the circuit and cable.
  • Choosing a fuse rating below the normal current because it is the nearest value. The rating must be just above the normal current.

Exam tips

  • "State" the hazard: name the danger itself. For damaged insulation or damp conditions, write an electric shock; for overheating cables or overloading, write a fire. "A short circuit" alone does not score.
  • "Explain" why the switch is in the live wire: say that switching off disconnects the appliance from the high p.d., so it is safe to touch.
  • To choose a fuse, write I=PVI = \frac{P}{V} with the numbers, give the current, then pick the smallest rating above it.
  • "Explain" how earthing works as a chain: live wire touches the metal casing, low-resistance earth wire, large current, fuse melts, live wire cut off, casing no longer live.

Key takeaways

Learn thisMains circuit: the live wire carries the high alternating p.d., the neutral wire stays near 0 V0\ \text{V}, and the earth wire joins a metal casing to the ground.
Learn thisThe switch and the fuse go in the live wire, so switching off or a melted fuse disconnects the appliance from the high p.d.
Learn thisHazards: damaged insulation (electric shock; also fire from a short circuit), overheating cables (fire), damp conditions (shock), overloaded sockets or extension leads (large total current, overheating, fire).
Learn thisA fuse melts, and a trip switch opens, when the current goes above its rating or setting. A trip switch can be reset. Choose the smallest available rating above the appliance's normal current, I=PVI = \frac{P}{V}.
Learn thisA metal casing must be earthed. A double-insulated appliance has a non-conducting casing and no earth wire, but still has a fuse, which protects the circuit and the cable.

Practise this

17 past-paper questions on Electrical safety in the 0625 Extended bank, each with a mark scheme and a worked explanation.

Practise Electrical safety →