In a the parts form one loop, so the same current passes through each, and add, as do the e.m.f.s of cells facing the same way. In a the current splits between branches, and each extra branch lowers the . The lamps in a house are wired in parallel so each can be switched on its own and the rest stay lit if one breaks.
You'll be able to
Use the fact that the current is the same at every point in a series circuit.
Build series and parallel circuits from a diagram, with and in the right places.
Add up the e.m.f.s of cells in series and the resistances of in series.
Compare the currents and the combined resistance in a parallel circuit, and give the advantages of wiring lamps in parallel.
Use the rules for currents at a and for p.d.s in series and parallel, and explain the junction rule using charge.
Work out the resistance of a pair of resistors joined in parallel.
Before you start3 quick questions on what this builds on
Check yourself
How do you connect an to measure the current in a lamp?
Check yourself
How do you connect a to measure the across a resistor?
Check yourself
The p.d. across a lamp is 3.6V and the current in it is 0.40A. What is the of the lamp, in Ω?
In a the components are joined one after another in a single loop. There is only one path, so all the charge that leaves the cell passes through every component.
One loop. Both ammeters read the same current.
So ammeters A1 and A2 give the same reading, wherever they sit in the loop. A lamp transfers energy from the charge. It does not use up the .
To build a circuit from a diagram, start at one terminal of the cell. Follow the wire round, connecting each part in turn, until you are back at the other terminal. Put the in the loop and add the last, across the part it measures.
Cells in series add their e.m.f.s, as long as they all face the same way (positive terminal to negative terminal). A cell turned round the wrong way subtracts its e.m.f. instead.
Learn this
E=E1+E2+E3
The is the single resistance that could replace a group of and take the same current from the same supply. In series, the charge has to pass through every resistor, so their resistances add.
Learn this
R=R1+R2+R3
Worked exampleResistors of 4.7Ω, 8.2Ω and 3.3Ω are connected in series. Calculate their combined resistance.
Try it first, then reveal one step at a time.
In series, add the resistances: R=R1+R2+R3.
R=4.7+8.2+3.3=16.2Ω
Check: the combined resistance is bigger than the largest one, 8.2Ω. That is always true in series.
R=16.2Ω
Worked exampleA torch has four 1.2V cells in series, all facing the same way. They are connected to a lamp of resistance 9.6Ω in series with a 2.4Ω resistor. Calculate the current in the lamp.
Try it first, then reveal one step at a time.
Combined e.m.f.: E=4×1.2=4.8V.
Combined resistance: R=9.6+2.4=12Ω.
Rearrange R=IV to I=RV, using the whole e.m.f. and the whole resistance.
I=124.8=0.40A. The circuit is one loop, so this is the current in the lamp too.
I=0.40A
Check yourself
A lamp and a resistor are in series with a cell. One ammeter is placed just before the lamp and another just after the resistor. Which statement about their readings is correct?
Check yourself
Four cells, each of e.m.f. 1.5V, are connected in series. One of them is turned round the wrong way. What is the combined e.m.f.?
Parallel circuits
In a the components sit on separate branches. Each branch is connected between the same two points. In a simple parallel circuit like the one below, those two points are the ends of the supply, so each branch is joined straight across it.
A1 reads the current from the cell. A2 and A3 each read one branch.
Worked exampleA lamp is connected to a battery. A second lamp is then connected in parallel with the first. State and explain what happens to the current from the battery.
Try it first, then reveal one step at a time.
State the change first.
Then explain it with the extra path and the combined resistance.
Finish by linking resistance to current for the same battery.
The current from the battery increases. The second lamp gives the charge another path. So the combined resistance of the two lamps is less than the resistance of one lamp. The battery's p.d. is the same, so a smaller resistance means a larger current.
The lamps in a house lighting circuit are connected in parallel, each on its own branch with its own switch.
Worked exampleState three advantages of connecting the lamps in a house lighting circuit in parallel rather than in series.
Try it first, then reveal one step at a time.
Think about what happens when one lamp is switched off or breaks.
Then think about the p.d. each lamp gets.
Each lamp can be switched on and off on its own. If one lamp breaks, the other lamps stay lit. Each lamp gets the full p.d. of the supply, so it lights at full brightness.
Check yourself
A cell is connected to two lamps in parallel. Which statement about the current from the cell is correct?
Check yourself
Resistors of 36Ω and 45Ω are joined in parallel. Which value could be their combined resistance?
Check yourself
You want to measure the current in just one lamp of a parallel circuit. Where do you connect the ammeter?
Currents at junctions, p.d.s in series and parallel Extended only
Learn this
I=I1+I2
Here I is the current into a junction that splits into two branches carrying I1 and I2. In the parallel circuit above, A1 reads the sum of A2 and A3.
Learn this
V=V1+V2
Worked exampleThree lamps are connected in parallel to a supply. The current from the supply is 1.30A. Two of the lamps carry 0.45A and 0.62A. Calculate the current in the third lamp.
Try it first, then reveal one step at a time.
The current from the supply splits at the junctions into the three branches.
So 1.30=0.45+0.62+I3.
I3=1.30−0.45−0.62=0.23A
I3=0.23A
Worked exampleA 9.0V supply is connected to a lamp in series with an 8.5Ω resistor. A voltmeter across the lamp reads 5.6V. Calculate the current in the circuit.
Try it first, then reveal one step at a time.
In series the p.d.s add up to the supply p.d.: 9.0=5.6+VR.
So the p.d. across the resistor is VR=9.0−5.6=3.4V.
Use I=RV for the resistor: I=8.53.4=0.40A.
The current is the same everywhere in series, so this is the current in the lamp too.
I=0.40A
Worked exampleExplain why the total current into a junction is equal to the total current out of it.
Try it first, then reveal one step at a time.
Start from what a current is.
Then say what happens to charge at the junction, and finish with the currents.
A current is a flow of charge. Charge is not used up, made or stored at the junction. So the charge arriving at the junction each second equals the charge leaving it each second. So the total current in equals the total current out.
Check yourself
A current of 0.85A flows into a junction. Two wires leave it. One carries 0.32A. What is the current in the other wire, in A?
Check yourself
Two lamps are connected in parallel with each other. This pair is in series with a resistor across a 12V supply. The p.d. across the resistor is 7.4V. What is the p.d. across each lamp?
Calculating resistance in parallel Extended only
For two resistors R1 and R2 in parallel, add their reciprocals. The answer is R1, so take the reciprocal again to get R.
Learn this
R1=R11+R21
Worked exampleResistors of 20Ω and 30Ω are joined in parallel. Calculate their combined resistance.
Try it first, then reveal one step at a time.
Write the equation: R1=R11+R21.
Substitute: R1=201+301=0.0833…
Take the reciprocal: R=0.0833…1=12Ω.
Check: 12Ω is less than 20Ω, the smaller resistor, as it must be.
R=12Ω
Worked exampleResistors of 15Ω and 10Ω are joined in parallel across a 4.5V supply. Calculate the current from the supply.
Try it first, then reveal one step at a time.
Combined resistance: R1=151+101, so R=6.0Ω.
Use I=RV: I=6.04.5=0.75A.
Check with the branches. Each has the full 4.5V: 154.5=0.30A and 104.5=0.45A.
At the junction, 0.30+0.45=0.75A, which matches.
I=0.75A
Check yourself
Resistors of 30Ω and 70Ω are joined in parallel. Find their combined resistance.
Check yourself
Two identical 56Ω resistors are connected in parallel. What is their combined resistance, in Ω?
Common mistakes
Thinking current is used up as it passes through a lamp or resistor. In a series circuit the current is the same at every point.
Adding resistances that are in parallel. That gives the series value; in parallel the combined resistance is less than the smallest resistor.
Dividing a cell's e.m.f. by the number of cells. Cells in series facing the same way add their e.m.f.s.
Connecting a voltmeter in series or an ammeter in parallel. The ammeter goes in the loop it measures; the voltmeter goes across the component.
Extended: forgetting to take the reciprocal after adding R11+R21.
Exam tips
"Calculate" a combined resistance: write the equation, then the numbers, then the answer with its unit, Ω. A missing unit can lose a mark.
Paper 1/2 multiple choice on resistors in parallel: cross out every option that is not less than the smallest resistor first.
"State" the advantages of lamps in parallel as separate points: own switch, others stay lit if one breaks, full supply p.d. for each lamp.
"Explain" the junction rule (Extended): mention charge. Current is a flow of charge, and charge is not used up or stored at the junction.
Key takeaways
Learn thisSeries circuit: one loop, so the current is the same at every point.
Learn thisR=R1+R2+R3(resistors in series)
Learn thisCells in series that all face the same way: add their e.m.f.s. A cell turned the other way subtracts its e.m.f.
Learn thisParallel circuit: the source supplies more current than any one branch carries. Two resistors in parallel have a combined resistance less than either one by itself.
Learn thisLamps in a lighting circuit are wired in parallel: each can be switched on its own, the rest stay lit if one breaks, and each gets the full supply p.d.
Learn thisTotal current into a junction = total current out, because charge is not used up or stored there. Series: the p.d.s across the components add up to the total p.d. Parallel: each branch has the same p.d. as the whole arrangement.
Learn thisR1=R11+R21(two resistors in parallel)
Practise this
67 past-paper questions on Series and parallel circuits in the 0625 Extended bank, each with a mark scheme and a worked explanation.