Apparatus, techniques and safety
In a minute
The practical papers test whether you can name apparatus, use it properly, pick the best tool for a job and work safely. Many marks come from small techniques, such as reading a scale at eye level, that keep readings close to the true value.
You'll be able to
- Name and draw common apparatus, and follow a method step by step, saying why each technique is used.
- Choose the best instrument or method for a measurement, and give the reason for your choice.
- Spot the hazards in an experiment and match each one to a precaution.
- Describe and explain the techniques that improve the of readings.
Before you start2 quick questions on what this builds on
Revise first: 1.4 Density
Naming, drawing and using apparatus
Paper 5 puts real apparatus in front of you. Paper 6 shows it in diagrams. Either way, you must name each piece, know what it does and follow a method one step at a time.
Names that come up often: clamp stand, boss and clamp, metre rule, measuring cylinder, top-pan balance, newton meter, thermometer, stopwatch, ammeter, voltmeter, ray box and optics pins.
To draw apparatus, use simple side-view outlines. Label each part with a line that touches it. Show a length with a double-headed arrow between the exact points you measure.
Some techniques appear again and again. When one thing is too small or too quick to measure well, measure many and divide: many sheets of paper, or many oscillations of a pendulum.
To find the volume of an irregular solid, use the .
Try it first, then reveal one step at a time.
- Convert to mm: .
- Divide by the number of cards: .
- Why it works: the ruler reads to . That is small next to , but bigger than one card.
Instructions in Paper 5 often include a step whose reason you may be asked for. Each step is there for safety or for a better reading.
Try it first, then reveal one step at a time.
- Ask what a current does to a thin wire, and how that would affect the next reading.
- Opening the switch stops the current, so the wire does not heat up. A hotter wire has a higher resistance, which would change the later readings. It also stops the cell running down.
Choosing the best apparatus or method
Choose an instrument whose range reaches the largest value you will measure, with scale divisions small compared with the reading. The smaller the quantity, the more a fine scale matters.
A measuring cylinder beats a beaker: beaker marks are rough guides. A narrow cylinder usually has finer divisions than a wide one, because the same volume makes a bigger change in level.
For short times, light gates connected to an electronic timer beat a hand-held stopwatch. They start and stop automatically, so your reaction time doesn't matter.
To justify a choice, give the reason: smaller divisions, no reaction time, or a larger quantity to measure. "It is more accurate" alone rarely scores.
Try it first, then reveal one step at a time.
- Compare the scale divisions, then say what that does to the reading.
- Use the measuring cylinder. Its scale has much smaller divisions: every , against every on the beaker. So the volume can be measured much closer to the true value.
Try it first, then reveal one step at a time.
- Compare the time being measured with a person's reaction time, about .
- Use light gates connected to an electronic timer. A person's reaction time is about , almost as long as the fall itself, so hand timing could be badly wrong. Light gates start and stop the timer automatically as the ball passes, so reaction time plays no part.
Hazards and safety precautions
A hazard is something that could cause harm. A precaution is what you do to reduce that risk. A good answer links the two: what could happen, and how your precaution stops it.
Hot water can scald. Stand up while you work, keep the container on the bench, and let apparatus cool before you move it.
Heavy masses on a spring or a newton meter can fall onto feet. Put a soft mat or a tray of sand underneath and keep your feet clear.
Wires, resistors and ray box lamps get hot when a current flows. Switch off between readings and don't touch them until they have cooled. Keep water away from mains equipment.
Try it first, then reveal one step at a time.
- Name what could cause harm here, then a precaution that matches it and how it helps.
- The hot water, beaker or tripod could scald or burn the student. The student should stand up while heating, so they can step back quickly if the beaker tips over, and hot water cannot pour onto their lap. They should also let the apparatus cool before moving it.
Techniques for accurate readings
Accuracy is not the same as . Precise readings are close to each other, but they can all be wrong by the same amount.
Looking at a scale from an angle shifts the reading: a parallax error. Put your eye level with the reading, looking at right angles to the scale.
Measuring cylinder: stand it on a level bench and read the bottom of the meniscus, the curved water surface.
Ruler: hold it close to the object and in line with the length. For an upright length, check the ruler is vertical with a set square. Use the zero mark, or subtract the starting reading.
Balance: zero (tare) it first, then place the object at the centre of the pan. Thermometer: stir the water, keep the bulb fully in it without touching the beaker, and wait until the reading stops changing.
Timing oscillations: start and stop the stopwatch as the bob passes a fixed marker at the centre of the swing, such as P in the pendulum figure.
Try it first, then reveal one step at a time.
- Think about where the ruler goes and where your eye goes.
- Hold the metre rule vertical and close to the string, so the scale lines up with the length. Read each end with your eye level with it, at right angles to the scale, to avoid parallax error.
Try it first, then reveal one step at a time.
- Compare how the bob moves at the centre and at the end of its swing.
- The bob moves fastest at the centre, so the moment it passes the marker is easy to judge. At the end of the swing it slows down and stops for an instant, so it is hard to judge exactly when it turns. The marker also gives the same fixed point to start and stop at every time.
Common mistakes
- Writing "read it carefully" or "be careful". Name the actual technique or precaution.
- Reading the top of a water meniscus, which gives too big a volume. Read the bottom, with your eye level with it.
- Giving a precaution that doesn't match the hazard, like goggles for masses on a spring. Name the hazard first.
- Saying "more accurate" with no reason. Say why: smaller divisions, no reaction time, or more oscillations timed.
Exam tips
- "Describe" a technique: say exactly what you do, such as "eye level with the bottom of the meniscus".
- "Explain" a step in a method: say what the step prevents or improves, such as heating of the wire.
- "Justify" a choice of apparatus: give the reason it is better, not just its name.
- Two versions of one idea, like "ruler vertical" and "ruler straight", earn one mark. Give two different techniques.
Key takeaways
Practise this
387 past-paper questions on Experimental skills and investigations in the 0625 Extended bank, each with a mark scheme and a worked explanation.