4.3.1 · CorePaper 1Paper 2Paper 3Paper 4Paper 5Paper 6

Circuit diagrams and circuit components

In a minute

A circuit diagram shows each part of a circuit as a standard symbol, joined by straight lines for the wires. You need to recognise and draw every symbol, and know what each part does: supply energy, switch or control the current, sense temperature or light, give out light, heat, movement or sound, or protect the circuit.

You'll be able to

  • Recognise and draw the standard symbols for each Core component, and read a circuit diagram.
  • Describe what each Core component does in a circuit, including how a and a respond to temperature and light.
  • Draw and read the symbols for a and a , and predict whether current passes through them.
Before you start3 quick questions on what this builds on
Check yourself
How is an connected to measure the current in a lamp?
Check yourself
What does a connected across a lamp measure?
Check yourself
The of a circuit increases, but the supply p.d. stays the same. What happens to the current?

Revise first: 4.2.2 Electric current, 4.2.3 Electromotive force and potential difference and 4.2.4 Resistance

Circuit symbols and diagrams

A circuit diagram is a map of a circuit. Each component is drawn as a standard symbol, and the wires are straight lines. Anyone who knows the symbols can build the circuit from the diagram.

Twelve circuit symbols. Cell: a long thin line and a short thick line. Battery: two cells joined. d.c. power supply: two small open circles marked plus and minus. a.c. power supply: two small open circles with a wavy line between them. Generator: a square with G. Open switch: a hinged line lifted away from its contact. Lamp: a circle with a cross. Motor: a circle with M. Electric bell: a dome on a flat base. Ammeter: a circle with A. Voltmeter: a circle with V. Junction of wires: a dot where three wires meet. cell battery +– d.c. power supply ~ a.c. power supply G generator switch (open) lamp M motor electric bell A ammeter V voltmeter junction of wires
Supplies, a switch, output devices and meters. A cell's long thin plate is its positive terminal.

Five symbols are circles: the lamp has a cross, and the motor, generator, and have the letters M, G, A and V. A battery is two or more cells joined in a row.

Ten circuit symbols. Fixed resistor: an empty rectangle. Variable resistor: a rectangle with a straight diagonal arrow through it. Potential divider: a rectangle with an arrow pointing onto its side from a third wire. Thermistor: a rectangle crossed by a diagonal line with a short flat foot at its lower end. Light-dependent resistor: a rectangle with two arrows pointing in towards it. Heater: a rectangle divided into sections. Fuse: a rectangle with the wire running through it along its length. Magnetising coil: a row of loops. Transformer: two coils side by side with two parallel lines, the core, between them. Relay coil: a small rectangle with the wire passing through it. fixed resistor variable resistor potential divider thermistor LDR heater fuse magnetising coil transformer relay coil
Many of these symbols are rectangles, so look at what is drawn on or through each one.

The rectangles differ only in what is added. An empty one is a fixed . A straight arrow through it makes a , and an arrow onto its side makes a .

A diagonal line with a flat foot is a . Two arrows pointing in make a (LDR). Sections inside make a heater, and a line along its whole length makes a .

To draw a circuit diagram, use a ruler and the standard symbols. Join the wires with no gaps, and put a dot at every junction where wires meet. Parts in one loop, one after another, are in series. Parts on separate branches between the same two points are in parallel.

A battery, a switch labelled P, a variable resistor labelled R and a motor labelled Q are joined in a single loop. A voltmeter is connected across the motor, with one lead on each side of it. M V P Q R battery
The circuit for a model fan.
Worked exampleThe diagram shows the circuit for a model fan. Name components P, Q and R. Name the meter and state how it is connected to Q.

Try it first, then reveal one step at a time.

  1. P is a hinged line lifted away from its contact: a switch, drawn open.
Worked exampleA car's rear window heater runs from a battery. A fuse, a switch and the heater are joined in series. A lamp, in parallel with the heater, shows when the heater is on. Draw the circuit diagram.

Try it first, then reveal one step at a time.

  1. Draw the battery as two cells in a row.
A battery, a fuse and a switch are joined in series. After the switch the wire splits at a junction into two parallel branches, one with a heater and one with a lamp. The branches join again at a second junction and the wire returns to the battery. battery fuse switch heater lamp
One correct answer. The switch turns the heater and the lamp on and off together.
Check yourself
Which component is drawn as a rectangle with two arrows pointing in towards it?
Check yourself
A student means to draw a fuse but draws an empty rectangle. Which component has the student drawn instead?

What each component does

Sources give the charge energy and push it round the circuit. A cell, a battery and a d.c. power supply give . An a.c. power supply, such as the mains, gives . A generator turns kinetic energy into electrical energy.

A switch closes the circuit (current flows) or opens it (no current). A fixed resistor has a set resistance that limits the current. A lets you change the . More resistance means a smaller for the same supply p.d., so a lamp in series gets dimmer or a motor slows.

A shares the supply's between two parts. With a sliding contact, it can give out any p.d. from zero up to the full supply p.d. You use it in 4.3.3.

Two components are sensors. A (the NTC type in this course) has a resistance that falls as its temperature rises. A has a resistance that falls as the light on it gets brighter.

Output devices transfer energy from the circuit. A gives out light, a heater heats its surroundings, a motor turns and an electric bell rings. A magnetising coil becomes a magnet while a current flows in it. Meters measure: an ammeter in series measures the current, and a voltmeter connected across a component measures the p.d. across it.

A contains a thin wire that melts if the current rises above the fuse's rating. That breaks the circuit and stops the current before the wires overheat. A transformer changes the size of an alternating p.d., such as mains p.d. down to a few volts for a charger. It works only with a.c. (4.5.6).

A is a switch worked by a magnetising coil. A small current in the coil closes a switch in a second circuit, which can carry a large current.

Two separate circuits joined by a relay. Left: a cell, a switch S and the relay coil form a small-current circuit. Right: a battery, a motor and the relay's switch contacts form a large-current circuit. A dashed arrow from the coil to the contacts shows that the coil closes the contacts when it is magnetised. M switch S small-current circuit large-current circuit relay coil contacts
A relay lets a small current switch on a large one.
Worked exampleIn the circuit shown, the motor needs a very large current. Explain how closing switch S makes the motor turn.

Try it first, then reveal one step at a time.

  1. Start in the small-current circuit: what does closing S do?
Worked exampleA thermistor, a lamp and a battery are connected in series. The thermistor is warmed with a hairdryer. Describe and explain what happens to the lamp.

Try it first, then reveal one step at a time.

  1. Describe the change first: brighter or dimmer?
Check yourself
An LDR, a lamp and a cell are in series. The room goes dark. What happens to the current in the lamp?
Check yourself
The current in a circuit rises above the rating of its fuse. What does the fuse do?
Check yourself
The resistance of a variable resistor in series with a motor is increased. The supply p.d. stays the same. What happens to the motor?

Diodes and LEDs Extended only

A lets current pass in one direction only. Its symbol is a triangle pointing at a bar. Current can pass when the triangle points along the , from the positive terminal round the circuit to the negative.

Connected that way (the forward direction), the diode has a low resistance and current flows. Turned round (reverse), its resistance is very high and almost no current flows, so it acts like an open switch.

A (LED) is a diode that gives out light when current passes through it in the forward direction. In reverse, almost no current flows and it stays dark. A resistor is usually placed in series with an LED to keep the current small.

Top: the diode symbol, a triangle pointing at a short bar, and the LED symbol, the same with two small arrows pointing away from it. Bottom: two circuits, A and B, each a cell, an LED and a resistor in series. The long plate of each cell, the positive terminal, is on the left. Conventional current leaves the positive terminal, goes left along the top wire, down the left side and right along the bottom wire through the LED and then the resistor. In A the LED triangle points right, along the current. In B the LED is turned round and points left, against the current. diode light-emitting diode (LED) A + – B + –
Follow the conventional current from the + terminal to each LED.
Worked exampleLook at circuits A and B in the diagram. Which LED lights? Explain your answer.

Try it first, then reveal one step at a time.

  1. Find the positive terminal: the long thin plate of the cell.
Check yourself
A cell, a diode and a lamp are in series, and the lamp is lit. The diode is turned round. What happens to the lamp?
Check yourself
How is the LED symbol different from the diode symbol?

Common mistakes

  • Mixing up the variable resistor and the thermistor. The variable resistor has a straight arrow through it; the thermistor's line has a flat foot and no arrowhead.
  • Calling a fuse a resistor. A fuse has a line running through the rectangle along its length; a fixed resistor is an empty rectangle.
  • Saying an NTC thermistor's resistance rises as it warms up. It falls, so the current in series with it rises.
  • Connecting a voltmeter across two components when you want the p.d. across one. Join its leads to the two ends of that one component only.
  • Extended: drawing an LED with its arrows pointing in. That is the LDR; an LED gives out light, so its arrows point away.

Exam tips

  • "Name" or "Identify" a component: give its full name, such as "light-dependent resistor" or "variable resistor", not just "resistor".
  • Paper 1/2 "which circuit contains…" questions: check every symbol in each circuit. One missing or wrong component rules that circuit out.
  • "Draw" a circuit diagram (Paper 3/4 or Paper 6): standard symbols, straight wires with no gaps, and a dot at each junction.

Key takeaways

Learn thisCircuit diagrams use the standard symbols, with wires drawn as straight lines and a dot at each junction.
Learn thisRectangle symbols: fixed resistor (empty), variable resistor (straight arrow through it), potential divider (arrow onto its side), thermistor (diagonal line with a flat foot), LDR (two arrows pointing in), heater (sections inside), fuse (line along its length).
Learn thisNTC thermistor: its resistance falls as its temperature rises. LDR: its resistance falls as the light on it gets brighter.
Learn thisWith the supply p.d. unchanged, more resistance in a series circuit means a smaller current.
Learn thisFuse: its thin wire melts when the current rises above its rating, breaking the circuit. Relay: a small current in its coil closes a switch in a second circuit that carries a large current.
Learn thisPotential divider: connected across a supply, it shares the supply p.d.; with a sliding contact, and the output taken between one end and the slider, it gives any p.d. from zero to the full supply p.d. Transformer: changes the size of an alternating p.d., and works only with a.c.
Learn thisDiode: current passes only when its triangle points along the conventional current; in reverse almost no current flows. LED: a diode that gives out light when current passes in the forward direction.

Practise this

5 past-paper questions on Circuit diagrams and circuit components in the 0625 Extended bank, each with a mark scheme and a worked explanation.

Practise Circuit diagrams and circuit components →