Effects of forces
In a minute
A can stretch, squash or bend an object, and it can change how the object moves. When the forces on an object balance, it stays at rest or keeps moving steadily in a straight line; a changes its speed or direction. Extended adds the , and motion in a circle.
You'll be able to
- Describe how forces change an object's size and shape, and how to measure the extension of a spring.
- Plot, sketch and read a , and tell from it when the extension is proportional to the load.
- Find the resultant of several forces that act along one straight line, with its direction.
- Use , and say how a resultant force can change an object's speed or direction.
- Describe between surfaces, and on objects moving through liquids and gases.
- Use , and find the on a load–extension graph.
- Use , with the in the direction of the resultant force.
- Describe how the force needed for depends on speed, radius and .
Before you start3 quick questions on what this builds on
Revise first: 1.2 Motion and 1.3 Mass and weight
Forces change shape: stretching a spring
A force is a push or a pull, measured in newtons (N). Forces can change the size and shape of an object: squeeze a sponge, stretch a rubber band or bend a ruler. They can also change how an object moves.
Hang a weight on a spring and it stretches. The weight is the load, in N. The increase in length is the extension, often written .
Clamp a metre rule upright beside the spring, with a pointer on its end. Read the length with no load, then after adding each slotted mass (, about ). Keep your eye level with the pointer: looking from above or below gives a parallax error.
Try it first, then reveal one step at a time.
- Set up the apparatus first, then say what is measured before any load goes on.
- Then say how each load is added, how each length is read and how the extension is found.
- Finish with how many readings and how they are recorded.
- Hang the spring from a clamp stand, fix a pointer to its bottom end and clamp a metre rule upright beside it. Measure the original length of the spring with no load. Hang a slotted mass on the spring and measure the new length, with your eye level with the pointer. Work out the extension as the new length minus the original length. Repeat with at least five different loads and record each load and extension in a table.
A can have load up the side or along the bottom, so read the axis labels first. Label each axis with the quantity and unit, such as load / N. Plot small crosses and draw one line of best fit; don't join the dots.
For a spring that isn't stretched too far, the points lie on a straight line through the origin. The extension is directly proportional to the load: double the load and the extension doubles.
Try it first, then reveal one step at a time.
- Find the extension first: .
- Go up from on the extension axis to the line, then across to the load axis.
- The load there is . Check: the line passes through at , so each centimetre takes , and .
- The load is the weight of the pencil case.
Spring constant and the limit of proportionality Extended only
is the load in N and is the extension: is in N/m with in m, or N/cm with in cm. A stiffer spring has a larger . With load up the side, the of the straight part is ; with extension up the side, it is .
Past this point the graph curves, so use only on the straight part.
Try it first, then reveal one step at a time.
- Write the equation: .
- Substitute: .
- . The extension is in metres, so the unit is N/m.
Try it first, then reveal one step at a time.
- Check the load is below the limit: is less than , so applies.
- Rearrange for the extension: .
- . is in N/cm, so is in cm.
- For a load you could not use : that load is past the limit of proportionality.
Resultant force and Newton's first law
The resultant force is the single force that has the same effect as all the forces on an object together. For forces along one straight line, choose one direction as positive and give forces the other way a minus sign. Then add them: the resultant points the way of the larger total.
Try it first, then reveal one step at a time.
- Forwards: .
- Backwards: .
- Resultant .
- It is positive, so it acts forwards. The barge is moving forwards, so it speeds up.
If the forces balance, the resultant force is zero. That doesn't mean the object is still.
A resultant force changes the velocity (speed in a given direction). In the direction of motion, the object speeds up; against it, it slows down; at right angles to it, it changes direction.
Try it first, then reveal one step at a time.
- Name the forces that do act along the road.
- Say how they compare, what that makes the resultant, and what Newton's first law then predicts.
- Forces do act on the bike: a forward driving force from the pedals, and friction and air resistance backwards. These forces are balanced, so the resultant force is zero. With zero resultant force, the bike keeps moving at a constant speed in a straight line.
Friction and drag
Friction is a force between two surfaces that touch. It can stop them sliding over each other, or slow down sliding that has started. Surfaces that rub together heat up: rub your hands, or feel a bike's brakes. Friction is often useful too: it lets shoes and tyres grip.
Friction on an object moving through a liquid or a gas is called drag: air resistance in air, water resistance in water. Drag acts against the motion and gets bigger as the object moves faster.
Try it first, then reveal one step at a time.
- Name the force and where it acts.
- Give its two effects: on the motion, and on the temperature.
- When the driver brakes, the brake pads press against the spinning discs and rub on them. Friction between the pads and the discs acts against the motion, so the car slows down. Friction between rubbing surfaces also causes heating, so the discs get hot.
Force, mass and acceleration Extended only
says how quickly a resultant force changes an object's velocity.
is the resultant force in N (not just one of the forces), is the mass in kg and is the acceleration in . The acceleration is always in the direction of the resultant force. A resultant force against the motion makes the object slow down: a .
Try it first, then reveal one step at a time.
- Find the resultant force first: forwards.
- Rearrange : .
- , forwards, the same direction as the resultant force.
Try it first, then reveal one step at a time.
- East is positive, so the resultant force is .
- .
- .
- The acceleration points west, the same way as the force and against her motion, so she slows down.
Motion in a circle Extended only
In at a constant speed, the direction keeps changing, so the velocity changes and a resultant force must act. It acts towards the centre, at right angles (perpendicular) to the motion, and changes the direction, not the speed. Tension in a string, friction on a bend or gravity on a satellite can provide it.
If the force stops and no other force acts, the object moves off in a straight line along the tangent (Newton's first law).
How big must the force be? Same mass and radius: a higher speed needs a larger force. Same speed and radius: a larger mass needs a larger force. Same mass and speed: a larger force gives a smaller radius. You only describe these rules in words: no equation for this force is needed.
Try it first, then reveal one step at a time.
- Say which force acts towards the centre.
- Use the rule for the same mass and radius.
- Then use the rule linking force and radius at a fixed speed.
- Friction is the force towards the centre that keeps the car moving in a circle. For the same mass and the same radius, a higher speed needs a larger force. So the friction must be larger. On ice the friction can't get that large, so the car can't follow the same circle: it moves onto a wider path, with a larger radius.
Common mistakes
- Using the spring's length instead of its extension. Extension is the stretched length minus the original length.
- Calling a straight line that misses the origin proportional. Proportional means a straight line through .
- Adding forces that act in opposite directions. Subtract them, and give the resultant's direction.
- Thinking zero resultant force means the object is at rest. It may be moving at a constant speed in a straight line.
- Extended: using a spring constant in N/cm with an extension in m. Convert so the units match.
- Extended: drawing the force on an object moving in a circle pointing outwards. It points towards the centre.
Exam tips
- "State" Newton's first law with both outcomes, at rest or constant speed in a straight line, and the condition: unless a resultant force acts.
- "Calculate": write the equation, then the numbers in it, then the answer with its unit. For a force, add its direction.
- "Describe" an experiment (Paper 5/6) in order: what you set up, what you measure first, what you change, and how you work out the result.
- "Sketch" a load–extension graph: label both axes with units, and draw a straight line from the origin for the proportional part.
Key takeaways
Practise this
90 past-paper questions on Effects of forces in the 0625 Extended bank, each with a mark scheme and a worked explanation.