Motion, forces and energy cheat sheet

BOOKLET given in the examLEARN you must remember it · Each block links to its lesson.

Motion, forces and energy

IGCSE PHYSICS 0625 · Extended
pastpaperprep.com/revision-notes

1.1Physical quantities and measurement techniques

Length: use a ruler, start at the zero mark (or subtract the starting reading), and look straight at the mark. Liquid volume: use a measuring cylinder; for water, read the bottom of the meniscus with your eye level with it.LEARN
Volume of an irregular solid that sinks: lower it into water in a measuring cylinder until it is fully under water. Its volume = new reading − starting reading.LEARN
Time: a clock for minutes or hours, a stopwatch for several seconds, a digital timer with light gates for intervals well under a second. Hand timing adds a reaction-time error of roughly 0.2 s0.2\ \text{s}.LEARN
Small distance or short time: measure many together (a stack, or 2020 oscillations) and divide by the number. Repeat and take the mean.LEARN
Period of a pendulum: the time for one complete oscillation, out, across and back to the start. Period = time for nn oscillations ÷ nn.LEARN
Scalars have size only: distance, speed, time, mass, energy, temperature. Vectors have size and direction: force, weight, velocity, acceleration, momentum, electric and gravitational field strength.LEARN
Two forces or two velocities at right angles: resultant =X2+Y2= \sqrt{X^2 + Y^2}, at angle θ\theta to XX where tan⁡θ=YX\tan\theta = \frac{Y}{X}. Or draw them tip to tail to scale and measure. Give the size and the direction.LEARN

1.2Motion

v=stv = \frac{s}{t}LEARN
Speed is the distance travelled per unit time (a scalar). Velocity is speed in a given direction (a vector).LEARN
average speed=total distance travelledtotal time taken\text{average speed} = \frac{\text{total distance travelled}}{\text{total time taken}}LEARN
Distance–time graph: the gradient is the speed. Horizontal line: at rest. Straight sloping line: constant speed. Curve getting steeper: speeding up; curve getting less steep: slowing down.LEARN
Speed–time graph: horizontal line above the time axis: constant speed; line along the time axis: at rest; sloping up: speeding up; sloping down: slowing down. The area under the graph is the distance travelled.LEARN
Near the Earth's surface the acceleration of free fall gg is approximately constant, about 9.8 m/s29.8\ \text{m/s}^2. With no air resistance, every object falls with this acceleration, whatever its mass.LEARN
a=ΔvΔta = \frac{\Delta v}{\Delta t}LEARN
For motion in a straight line, the gradient of a speed–time graph is the acceleration: a straight line means constant acceleration, a curve means changing acceleration. Taking the direction of motion as positive, a deceleration is a negative acceleration.LEARN
Falling from rest through air or a liquid, an object's acceleration decreases as the resistance grows with speed. When the forces on it balance (in air, when the air resistance equals its weight), the resultant force is zero and it falls at a constant terminal velocity.LEARN

1.3Mass and weight

Mass is the quantity of matter in an object, in kg. It changes only if matter is added or removed, so moving or reshaping an object doesn't change it.LEARN
Weight is the pull of gravity on an object's mass. It is a force, so it is measured in newtons (N), not kg.LEARN
g=Wmg = \frac{W}{m}LEARN
Gravitational field strength gg means force per unit mass, in N/kg: the pull of gravity on each kilogram. Near the Earth's surface it is about 9.8 N/kg9.8\ \text{N/kg}, equal to the acceleration of free fall, about 9.8 m/s29.8\ \text{m/s}^2.LEARN
A beam balance has its pivot at the centre, with the pans at equal distances from it. It is level when the weights in its two pans are equal. Both pans have the same gg, so the masses are equal too.LEARN
Weight is the effect of a gravitational field pulling on a mass, W=mgW = mg. Where gg is different (the Moon, another planet, far from the Earth), the weight changes but the mass stays the same.LEARN

1.4Density

ρ=mV\rho = \frac{m}{V}LEARN
Density is mass per unit volume, in g/cm³ (mass in g, volume in cm³) or kg/m³ (mass in kg, volume in m³). 1 g/cm3=1000 kg/m31\ \text{g/cm}^3 = 1000\ \text{kg/m}^3.LEARN
To measure density, find the mass with a balance and the volume, then divide. Liquid: volume in a measuring cylinder, mass = (cylinder + liquid) − empty cylinder. Regular solid: volume from length × width × height. Irregular solid that sinks: volume = rise in water level when it is fully under water (displacement).LEARN
An object floats in a liquid if its density is less than the liquid's density, and sinks if its density is greater. For a hollow object, use its average density.LEARN
Liquids that do not mix form layers in order of density: the least dense on top, the densest at the bottom, whatever their volumes.LEARN

1.5.1Effects of forces

A force can change an object's size and shape, its speed and its direction of motion. Forces are measured in newtons (N).LEARN
Extension = stretched length − original length. A load–extension graph that is a straight line through the origin shows the extension is directly proportional to the load.LEARN
k=Fxk = \frac{F}{x}LEARN
Spring constant kk: force per unit extension, in N/m or N/cm. It holds only up to the limit of proportionality, where the straight part of the load–extension graph ends.LEARN
Resultant of forces along one line: add the forces that point the same way, subtract those that point the opposite way, and give the size and direction.LEARN
Newton's first law: with zero resultant force, an object stays at rest or moves at a constant speed in a straight line. A resultant force changes its speed, its direction, or both.LEARN
Friction acts between surfaces that touch: it can oppose motion, and it heats surfaces that rub. Drag is friction in a liquid or gas (air resistance in air): it opposes the motion and grows with speed.LEARN
F=maF = maLEARN
In F=maF = ma, FF is the resultant force, and the acceleration is in the same direction as the resultant force.LEARN
Circular motion at constant speed needs a resultant force towards the centre, perpendicular to the motion. The force must be larger for a higher speed (same mass and radius) or a larger mass (same speed and radius). A larger force gives a smaller radius (same mass and speed).LEARN

1.5.2Turning effect of forces

Moment: the turning effect of a force about a pivot, in N m (or N cm when distances are in cm).LEARN
moment=force×perpendicular distance from the pivot\text{moment} = \text{force} \times \text{perpendicular distance from the pivot}LEARN
Principle of moments: when an object is in equilibrium, the clockwise moments about any point add up to the same total as the anticlockwise moments about that point.LEARN
An object is in equilibrium only when there is no resultant force on it and no resultant moment on it. Balanced forces alone are not enough.LEARN
With several forces, add all the clockwise moments and all the anticlockwise moments about the pivot. A uniform beam's own weight acts at its middle, so it has a moment unless the pivot is there.LEARN
To test the principle: balance a metre rule at its centre with weights on both sides, measure each distance from the pivot, and show the total clockwise and anticlockwise moments are equal.LEARN

1.5.3Centre of gravity

The centre of gravity is the point through which all the weight of an object can be taken to act. For a uniform object it lies on every line of symmetry, so for a uniform ruler, rectangular sheet or ring it is at the centre.LEARN
To find the centre of gravity of a flat irregular sheet: hang it freely from a pin and mark the vertical line of a plumb line from the pin. Repeat from a second hole. The centre of gravity is where the two lines meet.LEARN
A tilted object, when released, falls back onto its base if the vertical line down from its centre of gravity passes inside the base. It topples if the line passes outside the base.LEARN
An object is more stable when its centre of gravity is lower or its base is wider: it must tilt further before it topples.LEARN

1.6 ◆Momentum

p=mvp = mvLEARN
Momentum is mass × velocity, in kg m/s. It is a vector: choose a positive direction and give momentum the other way a minus sign.LEARN
impulse=FΔt=Δ(mv)\text{impulse} = F\Delta t = \Delta(mv)LEARN
Impulse is force × the time the force acts for. The impulse of the resultant force equals the change in momentum, final minus initial, and its unit N s is the same as kg m/s.LEARN
F=ΔpΔtF = \frac{\Delta p}{\Delta t}LEARN
Resultant force = change in momentum ÷ time taken, the rate of change of momentum. For the same change in momentum, a longer time gives a smaller average force: this is how airbags and crumple zones work.LEARN
Conservation of momentum: in a collision or explosion, total momentum before = total momentum after, provided no resultant force from outside acts on the objects.LEARN

1.7.1Energy

The seven energy stores: internal (thermal), kinetic, gravitational potential, elastic (strain), chemical, nuclear and electrostatic. Light, sound and electrical work transfer energy; they are not stores.LEARN
Energy is transferred between stores by mechanical work (forces), electrical work (currents), heating, and waves (electromagnetic, sound and others).LEARN
Conservation of energy: energy cannot be created or destroyed, only transferred from one store to another, so the total stays the same. Energy in = useful energy out + wasted energy.LEARN
Ek=12mv2E_\text{k} = \tfrac{1}{2}mv^2LEARN
ΔEp=mgΔh\Delta E_\text{p} = mg\Delta hLEARN
In ΔEp=mgΔh\Delta E_\text{p} = mg\Delta h, Δh\Delta h is the change in vertical height, not the distance along a slope, and g=9.8 N/kgg = 9.8\ \text{N/kg} near the Earth's surface.LEARN
With no friction or air resistance, the energy a falling object loses from its gravitational potential store all goes into its kinetic store. For an object falling from rest: mgΔh=12mv2mg\Delta h = \tfrac{1}{2}mv^2.LEARN
Sankey diagram: each arrow's width is proportional to the energy it carries. Useful energy usually goes straight on and wasted energy branches off. The energies out add up to the energy in.LEARN

1.7.2Work

W=Fd=ΔEW = Fd = \Delta ELEARN
Work done = energy transferred. A force that moves an object does mechanical work; an electric current does electrical work.LEARN
In W=FdW = Fd, dd is how far the object moves in the direction of the force. A force does no work on an object that doesn't move, or that moves at right angles to the force.LEARN
Work and energy are both measured in joules: 1 J=1 N m1\ \text{J} = 1\ \text{N m}, the work done when a force of 1 N1\ \text{N} moves an object 1 m1\ \text{m} in the direction of the force.LEARN
Lifting at a steady speed: the lifting force equals the weight, so the work done by the lifting force is weight × height gained.LEARN
Rearranged: F=WdF = \frac{W}{d} and d=WFd = \frac{W}{F}. On level ground, when the braking force is the only force slowing a vehicle, a constant braking force times the braking distance (the distance it travels while braking) equals the energy taken from its kinetic store.LEARN

1.7.3Energy resources

efficiency=useful energy outputtotal energy input×100%\text{efficiency} = \frac{\text{useful energy output}}{\text{total energy input}} \times 100\%LEARN
efficiency=useful output powertotal input power×100%\text{efficiency} = \frac{\text{useful output power}}{\text{total input power}} \times 100\%LEARN
In a power station, fossil fuels, biofuels and nuclear fuel heat water in a boiler into steam; in geothermal power, hot rocks underground turn water into steam. The steam spins a turbine, which drives a generator.LEARN
Hydroelectric, tidal, wave and wind power need no boiler: moving water or air drives the turbine or generator directly. Solar cells turn light straight into electrical power; solar panels heat water.LEARN
Non-renewable: fossil fuels and nuclear fuel. Renewable: biofuels, hydroelectric, tides, waves, wind, solar and geothermal.LEARN
Compare resources by renewability, availability (where), reliability (when), scale (how much) and environmental impact. Wind, waves and solar depend on the weather or daylight.LEARN
A more efficient device transfers a larger fraction of its input energy usefully. The rest is wasted, usually as thermal energy to the surroundings. Efficiency can never be more than 100%.LEARN
The Sun's radiation is where most resources get their energy. The exceptions are geothermal, nuclear fuel and tides.LEARN
The Sun releases energy by nuclear fusion. Research is under way to use fusion to generate electrical power on a large scale.LEARN

1.7.4Power

P=WtP=ΔEtP = \frac{W}{t} \qquad P = \frac{\Delta E}{t}LEARN
Power is the work done per unit time, or the energy transferred per unit time.LEARN
Power is measured in watts: 1 W=1 J/s1\ \text{W} = 1\ \text{J/s}, 1 kW=1000 W1\ \text{kW} = 1000\ \text{W}, 1 MW=1 000 000 W1\ \text{MW} = 1\,000\,000\ \text{W}.LEARN
Rearranging P=ΔEtP = \frac{\Delta E}{t} gives ΔE=Pt\Delta E = Pt and t=ΔEPt = \frac{\Delta E}{P}, where ΔE\Delta E is the energy transferred and tt the time. With the power in W and the time in s, the energy is in J.LEARN
Doing the same work in less time needs more power. Power says how fast energy is transferred, not how much in total or how efficiently.LEARN

1.8Pressure

Pressure is force per unit area, with the force at right angles to the surface. Its unit is the pascal: 1 Pa=1 N/m21\ \text{Pa} = 1\ \text{N/m}^2. With an area in cm², pressure is in N/cm².LEARN
p=FAp = \frac{F}{A}LEARN
A bigger force on the same area gives a bigger pressure. The same force on a smaller area gives a bigger pressure (knife, nail); on a larger area it gives a smaller pressure (snowshoes, wide tyres).LEARN
In a liquid at rest, the pressure increases with depth below the surface and with the density of the liquid. It doesn't depend on the shape or width of the container.LEARN
Δp=ρgΔh\Delta p = \rho g \Delta hLEARN

Which method when

'Find the density of an irregular solid that sinks, such as a stone' → mass on a balance; volume = rise in the measuring-cylinder reading once it is fully under water (or the overflow from a full displacement can); then ρ=mV\rho = \dfrac{m}{V}, with g and cm³ giving g/cm³ (1.4)LEARN
'Find the period of a pendulum' → time 2020 complete oscillations (out and back) from a fixed marker at the centre of the swing, repeat and take the mean, then divide by the number of oscillations (1.1)LEARN
'Find the speed from a straight section of a distance–time graph' → read the distance and time at both ends of that section and divide the change in distance by the change in time; the end reading ÷ its time works only if the section starts at the origin (1.2)LEARN
'Find the distance travelled from a speed–time graph made of straight lines' → find the area under the line: a rectangle (speed × time) where the speed is constant, a triangle (12\tfrac{1}{2} × base × height) where it changes steadily from or to zero, a rectangle plus a triangle where it changes steadily between two non-zero speeds, then add the parts (1.2)LEARN
'A see-saw or beam balances with one force each side of the pivot: find a force or a distance' → with the beam light, or uniform and pivoted at its centre, set clockwise moment = anticlockwise moment, F1d1=F2d2F_1 d_1 = F_2 d_2, measuring each perpendicular distance from the pivot, not from the end (1.5.2)LEARN
'Find the constant braking force from the braking distance' → on level ground with the brakes the only thing slowing it, the work done by the brakes equals the kinetic energy removed, so F=WdF = \dfrac{W}{d} with WW in J (1.7.2)LEARN
'Find the useful power of a student running upstairs or a motor lifting a load at a steady speed' → work done = weight × vertical height gained, then divide by the time in seconds (1.7.4)LEARN
'Find the pressure a table or vehicle exerts on level ground' → the force is its weight (W=mgW = mg), the area is all the legs or wheels in contact added together, then p=FAp = \dfrac{F}{A} with N and m² for Pa (1.8)LEARN

◆Which method when

'A uniform metre rule balances on a pivot away from its 50 cm mark: find a weight' → the rule's own weight acts at the 50 cm mark and has a moment too; add all the clockwise and all the anticlockwise moments about the pivot and set the totals equal (1.5.2)LEARN
'Given a driving force, resistive forces and the mass, find the acceleration' → find the resultant force first (forces the other way count as negative), then a=Fma = \dfrac{F}{m}; the acceleration is in the direction of the resultant force (1.5.1)LEARN
'An object's weight on Earth is given: find its weight on the Moon or Mars' → find its mass with Earth's gg, m=Wgm = \dfrac{W}{g}; the mass is the same there, so multiply it by the new gg (1.3)LEARN
'Two trolleys collide and stick together, or push apart from rest: find a velocity' → choose a positive direction, then set total momentum before = total momentum after (no outside resultant force), adding both masses if they stick (1.6)LEARN
'A ball bounces back off a wall: find the impulse or the average force' → give the two velocities opposite signs, find m(v−u)m(v - u), then divide by the contact time (1.6)LEARN
'Explain how an airbag or crumple zone protects the driver' → the change in momentum is the same, the stopping time is longer, so F=ΔpΔtF = \dfrac{\Delta p}{\Delta t} is smaller (1.6)LEARN
'An object falls or slides from rest, ignore air resistance and friction: find its speed' → set mgΔh=12mv2mg\Delta h = \tfrac{1}{2}mv^2 with Δh\Delta h the vertical drop, then take the square root (1.7.1)LEARN
Follows the Cambridge IGCSE Physics 0625 syllabus (2026 to 2028). Not affiliated with Cambridge.