5.4 · SLPaper 1Paper 2

Activation energy and catalysts

In a minute

Most collisions don't lead to a reaction, because the particles don't hit hard enough. The is the energy barrier a must get over. A higher gives more particles enough energy, as the shows. A lowers the barrier instead.

You'll be able to

  • Define activation energy and mark it on for exothermic and endothermic reactions.
  • Use Maxwell–Boltzmann curves to explain why a higher temperature makes successful collisions more likely.
  • Explain how a catalyst increases the rate, using an energy profile and a Maxwell–Boltzmann curve.
  • State what a catalyst leaves unchanged: ΔH\Delta H, the particles' energies and the position of equilibrium.
Before you start3 quick questions on what this builds on
Check yourself
A sealed sample of gas is heated. What happens to its particles?
Check yourself
On an energy profile for an exothermic reaction, where are the products?
Check yourself
According to , what must a collision have to lead to a reaction?

Revise first: 1.1 The particulate nature of matter, 4.1 Measuring enthalpy changes and 5.3 Rates of reaction and collision theory

Activation energy

Methane and air can sit mixed for years without reacting, though burning methane releases a lot of energy. A spark starts it at once.

Something holds the reaction back: an energy barrier. Bonds must start to break before new ones form, and that costs energy. Colliding particles react only if they bring enough energy to get over it.

On an , EaE_\text{a} is the rise from the reactants to the top of the hump, the transition state. The , ΔH\Delta H, runs from reactants to products.

Two energy profiles, potential energy against reaction coordinate. Left, exothermic: the curve starts at a reactants level, rises over a hump and falls to a products level below the reactants. An upward arrow from the reactants level to the top of the hump is labelled activation energy, and a downward arrow from reactants to products is labelled delta H, negative. Right, endothermic: the products level is above the reactants level. An upward arrow from the reactants level to the top of the hump is labelled activation energy, and an upward arrow from reactants to products is labelled delta H, positive. In both, the activation energy is measured from the reactants up to the peak. ExothermicEndothermic potential energy reaction coordinate potential energy reaction coordinate EaΔH < 0reactantsproducts EaΔH > 0reactantsproducts
EaE_\text{a} is always measured up from the reactants, and it is always positive. Only ΔH\Delta H changes sign.

The size of ΔH\Delta H says nothing about speed. A very exothermic reaction can be very slow if EaE_\text{a} is large.

Worked exampleAn energy profile is drawn on a scale in kJ mol−1\pu{kJ mol-1}. The reactants are at 3030, the top of the hump is at 215215 and the products are at 140140. Determine the activation energy of the reverse reaction.

Try it first, then reveal one step at a time.

  1. Forward EaE_\text{a}: reactants to peak, 215−30=185 kJ mol−1215 - 30 = \pu{185 kJ mol-1}.
Worked exampleA methane–air mixture does not react at room temperature, though methane combustion is very exothermic. Lit by a spark, it keeps burning. Explain this.

Try it first, then reveal one step at a time.

  1. Name the barrier: EaE_\text{a} is high.
Check yourself
On an energy profile, which difference is the forward activation energy?
Check yourself
A reaction has ΔH=−64 kJ mol−1\Delta H = \pu{-64 kJ mol-1} and Ea=38 kJ mol−1E_\text{a} = \pu{38 kJ mol-1}. Calculate the activation energy, in kJ mol−1\pu{kJ mol-1}, of the reverse reaction.

The Maxwell–Boltzmann distribution and temperature

The particles in a gas don't all have the same energy. Collisions keep passing energy around, so some are slow, most are middling and a few are very fast.

Draw four features. The curve starts at the origin: no particle has zero energy. It rises to a peak at the most likely energy.

Then it falls in a long tail that approaches the energy axis but never touches it. The area under the curve stands for all the particles in the sample.

Maxwell-Boltzmann distribution, fraction of particles against kinetic energy, at two temperatures. Both curves start at the origin, rise to a peak and then fall away in a long tail that gets closer to the energy axis without touching it. The curve at the lower temperature T1 has a taller, narrower peak at lower energy. The curve at the higher temperature T2 has a lower peak further to the right and a fatter tail. The two curves cross once, to the right of both peaks. A vertical dashed line marks the activation energy, well out in the tail. The area under each curve beyond the activation energy is shaded, and the shaded area is much larger for T2 than for T1. fraction of particles kinetic energy 0 EaT1T2 (higher)particles withE ≥ Ea
Only particles right of EaE_\text{a} can react on collision. At the higher temperature, T2T_2, that area is much larger.

At a higher temperature the average kinetic energy is higher. The peak moves right and gets lower, and the curve spreads. The area stays the same: the number of particles hasn't changed.

Hotter particles also collide a little more often, but that is the smaller effect.

Worked exampleNitrogen dioxide gas decomposes faster at 650 K\pu{650 K} than at 600 K\pu{600 K}. Explain why, with reference to the Maxwell–Boltzmann distribution.

Try it first, then reveal one step at a time.

  1. Say what temperature does to the particles.
Worked exampleFor one reaction, the fraction of collisions with at least EaE_\text{a} is 2.0×10−92.0 \times 10^{-9} at 300 K\pu{300 K} and 6.8×10−96.8 \times 10^{-9} at 320 K\pu{320 K}. Calculate how many times larger the fraction is at 320 K\pu{320 K}. Give 2 significant figures.

Try it first, then reveal one step at a time.

  1. Divide: 6.8×10−92.0×10−9=3.4\frac{6.8 \times 10^{-9}}{2.0 \times 10^{-9}} = 3.4, to 2 significant figures like the data.
Check yourself
A sealed sample of gas is heated. What happens to the area under its Maxwell–Boltzmann curve?
Check yourself
How does the Maxwell–Boltzmann curve of a gas at 350 K\pu{350 K} compare with its curve at 400 K\pu{400 K}?

Catalysts

To cross a mountain, you can give more people the energy to climb it, or find a lower pass. Heating does the first. A catalyst is the lower pass.

A takes part but is made again by the end, so it isn't in the overall equation. Biological catalysts are called enzymes.

Two energy profiles, each with an uncatalysed curve and a catalysed curve. Left, exothermic; right, endothermic. In each panel both curves start at the same reactants level and end at the same products level. The catalysed curve, drawn dashed, rises over a much lower hump than the uncatalysed curve. Two upward arrows from the reactants level show the activation energies: the longer one reaches the top of the uncatalysed hump, the shorter one, labelled activation energy catalysed, reaches the top of the catalysed hump. One arrow between the reactants and products levels is labelled delta H, the same for both pathways. ExothermicEndothermic potential energy reaction coordinate potential energy reaction coordinate EaEa(cat)ΔH < 0reactantsproducts EaEa(cat)ΔH > 0reactantsproducts without catalystwith catalyst
Same start, same finish, lower hump. The catalyst changes EaE_\text{a} but not ΔH\Delta H.

On a Maxwell–Boltzmann curve, a catalyst leaves the curve alone, because the temperature is the same. It moves EaE_\text{a} to lower energy.

One Maxwell-Boltzmann distribution, fraction of particles against kinetic energy, at a single temperature. Two vertical dashed lines cross the tail. The left line, at lower energy, is the activation energy with a catalyst. The right line, at higher energy, is the activation energy without a catalyst. The area under the curve to the right of the catalysed line is shaded, and it is much larger than the darker shaded area to the right of the uncatalysed line. The curve itself is the same in both cases. fraction of particles kinetic energy 0 Ea with catalystEa without catalyst
With a catalyst, every particle right of the lower EaE_\text{a} line can react.
Worked exampleAmmonia is made from nitrogen and hydrogen over iron. Explain how the iron increases the rate, with reference to the Maxwell–Boltzmann distribution.

Try it first, then reveal one step at a time.

  1. Say what the catalyst does to the route and to EaE_\text{a}.
Worked exampleA reaction has ΔH=−58 kJ mol−1\Delta H = \pu{-58 kJ mol-1} and Ea=132 kJ mol−1E_\text{a} = \pu{132 kJ mol-1}. A catalyst lowers the activation energy of the forward reaction to 87 kJ mol−1\pu{87 kJ mol-1}. Calculate the activation energy of the catalysed reverse reaction.

Try it first, then reveal one step at a time.

  1. The catalyst doesn't move the products: ΔH\Delta H is still −58 kJ mol−1\pu{-58 kJ mol-1}.

So a catalyst lowers both barriers equally and speeds up both directions equally. Equilibrium is reached sooner, but its position and KK don't change (5.9).

Check yourself
A catalyst is added at constant temperature. Which of these changes?
Check yourself
How does a catalyst change the Maxwell–Boltzmann picture?

Common mistakes

  • Measuring EaE_\text{a} from zero or from the products. The forward EaE_\text{a} starts at the reactants.
  • Labelling the Maxwell–Boltzmann energy axis "potential energy". It is kinetic energy.
  • Giving the hotter curve a bigger area or a higher peak. Same area, lower peak, further right.
  • Saying a higher temperature lowers EaE_\text{a}. Temperature changes the curve; a catalyst changes EaE_\text{a}.

Exam tips

  • "Explain" a rate change with the Maxwell–Boltzmann curve: what changes (the curve, or EaE_\text{a}), then more particles with E≥EaE \ge E_\text{a}, then more successful collisions per unit time.
  • In Paper 1A, an option saying a catalyst changes ΔH\Delta H, KK or the particles' energy is wrong.

Key takeaways

Learn thisEaE_\text{a}: the minimum energy colliding particles need to react, measured from the reactants up to the peak.
Learn thisEa(reverse)=Ea(forward)−ΔHE_\text{a}(\text{reverse}) = E_\text{a}(\text{forward}) - \Delta H
Learn thisMaxwell–Boltzmann curve: fraction of particles against kinetic energy; starts at the origin; tail never touches the axis; the area stands for all the particles.
Learn thisHigher temperature: lower peak further right, same area, more particles with E≥EaE \ge E_\text{a}, more successful collisions per unit time.
Learn thisA catalyst gives an alternative pathway with lower EaE_\text{a} and is not used up. Enzymes are biological catalysts.
Learn thisA catalyst doesn't change ΔH\Delta H, the Maxwell–Boltzmann curve, the equilibrium position or KK.

Practise this

56 past-paper questions on Energy profiles and catalysts in the Chemistry HL bank, each with a mark scheme and a worked explanation.

Practise Energy profiles and catalysts →