Measuring enthalpy changes
In a minute
Every reaction moves energy between the (the reacting chemicals) and its surroundings. An gives heat out and warms the surroundings; an takes heat in and cools them. You find the , , from the change of a known mass of water.
You'll be able to
- Describe a reaction in terms of the system and its surroundings, and tell heat apart from temperature.
- Classify a reaction as exothermic or endothermic from its temperature change, and give the sign of .
- Sketch and interpret , and use them to compare the stability of reactants and products.
- Calculate from a temperature change using and .
- Explain why usually measures a smaller temperature change than expected, and suggest improvements.
Before you start3 quick questions on what this builds on
Revise first: 1.1 The particulate nature of matter, 1.6 The mole and molar mass, 1.8 Concentration and Avogadro's law and 1.9 Ideal gases
System, surroundings and heat
The is the chemicals that react. The surroundings are everything else: the water, the beaker, the thermometer and the air.
Energy is never created or destroyed. In a reaction, energy moves between the system and the surroundings, and the total stays the same.
Heat is energy transferred from a hotter object to a colder one, in joules (J). measures the average kinetic energy of the particles. It is read in degrees Celsius or kelvin (K), but only the kelvin value is proportional to that energy. A hot spark has a high temperature but holds little energy, because it has so few particles.
An loses energy from the system, so its , , is negative. An gains energy, so is positive.
Try it first, then reveal one step at a time.
- The system is the dissolving solid. The water, the pack and your hand are the surroundings.
- The temperature falls, so energy moves into the system: endothermic, with positive.
- The ammonium nitrate dissolving absorbs heat from the surroundings, which include the water and your hand. The surroundings lose energy, so their temperature falls. The process is endothermic, so is positive.
Try it first, then reveal one step at a time.
- Temperature is an average per particle. It says nothing about how many particles there are.
- Compare the masses: the heat passed on depends on both temperature and mass.
- Temperature is a measure of the average kinetic energy of the particles. The spark has the higher temperature, but it has a tiny mass, so it has very few particles and transfers little heat. The tea has a much larger mass, so it transfers far more heat to your skin.
Energy profiles and stability
Every substance has potential energy that depends on its bonds: for the same atoms, stronger bonds mean lower potential energy. The lower a substance's potential energy, the more stable it is.
The reaction coordinate runs from reactants (left) to products (right) and has no units. The hump is the barrier, covered in 5.4.
is the enthalpy, the energy stored in the chemicals. Only the start and finish levels set , not the hump.
Try it first, then reveal one step at a time.
- is finish minus start; the hump doesn't enter it.
- . The products are lower, so they are more stable.
Try it first, then reveal one step at a time.
- Endothermic means the products sit higher in energy than the reactants.
- The reactants are low because the triple bond is very strong (see 2.2).
- The products are less stable than the reactants. Nitrogen is very stable because its triple bond is very strong. So the products have a higher potential energy than the reactants, and energy is absorbed from the surroundings. The reaction is endothermic and is positive.
Calculating $\Delta H$ from a temperature change
You can't measure stored chemical energy directly. Instead, the reaction heats or cools a known mass of water, a pure substance, and you measure its temperature change. This is .
An open beaker stays at constant pressure, so the heat exchanged is the , given per of reaction as written.
A standard state is the pure, most stable form at , or for a solution. This for the is not (), which is for gas volumes.
is the heat gained by the water (J), its mass (g), and the final minus initial temperature. For water, the is (data booklet, section 2). The formula is in section 1.
is the amount, in mol, of the reactant used up (the ). This gives per mole of that reactant, which is per mole of reaction only when its coefficient in the equation is 1. Divide by 1000 first, to get kJ. A change of equals , so Celsius readings give directly.
The minus sign does the bookkeeping: water warming ( positive) means the system lost energy, so is negative.
Try it first, then reveal one step at a time.
- Treat the solution as water, so .
- .
- Zinc is in excess, so all the copper(II) sulfate reacts: .
- . The solution warmed, so a negative value fits.
Try it first, then reveal one step at a time.
- . The water lost heat.
- ( values, data booklet section 7), so .
- . The water cooled, so a positive value fits.
Calorimetry in practice
For a solution, react it in a polystyrene cup with a lid. For a fuel, burn it in a spirit burner under a can of water, weighing the burner before and after.
Measured temperature changes are usually smaller than theory predicts. Heat escapes to the air or warms the can instead of the water, and incomplete combustion releases less energy. In an endothermic reaction, heat flowing in from the surroundings makes the fall smaller in the same way.
These are : repeats don't remove them. The measured is smaller in size than the true value, so less negative for an exothermic reaction.
To cut heat loss, use a lid, insulation and a draught shield, and stir. For a slow reaction, extrapolate the later part of the temperature–time graph back to the time of mixing to estimate the true maximum (or, if the reaction is endothermic, the true minimum).
Try it first, then reveal one step at a time.
- Fuel burned: . , so .
- .
- . The data booklet (section 14) gives , so much heat was lost.
Try it first, then reveal one step at a time.
- Say where the missing energy went, then link it to the temperature rise.
- Suggest a change that reduces heat loss, not one that only improves precision.
- Heat is lost to the surroundings, such as the air and the can, instead of heating the water. Incomplete combustion also releases less energy. So the temperature rise of the water is smaller than expected, and the calculated value is less negative. Putting a lid on the can and a draught shield round the flame would reduce heat loss.
Common mistakes
- Getting the sign backwards. The water or solution warming means negative; cooling means positive.
- Using the mass of the fuel or solid in instead of the mass of the water.
- Leaving in joules. Divide by 1000 so is in .
- Dividing by the amount of a reactant in excess. Use the amount used up or burned.
- Saying heat loss makes more negative. It makes the measured value less negative.
Exam tips
- "Calculate" : show with numbers, then , then with its sign and unit. Each line earns credit.
- "Sketch" an energy profile: label the axes potential energy and reaction coordinate, and draw from reactants to products.
- In Paper 1A calorimetry questions, options often differ only in sign or by a factor of 1000. Settle both first.
- "Explain" a low result: heat loss to the surroundings, so a smaller temperature rise. "Suggest" a fix that cuts heat loss, not a more precise instrument.
Key takeaways
Practise this
56 past-paper questions on Calorimetry and enthalpy in the Chemistry HL bank, each with a mark scheme and a worked explanation.