2.12 · SLPaper 1Paper 2

Current, potential difference and emf

In a minute

An is a flow of , such as electrons in a metal, and I=ΔqΔtI = \frac{\Delta q}{\Delta t}. A cell is a source of : it gives energy to each coulomb of charge. is the energy each coulomb gives up between two points, V=WqV = \frac{W}{q}.

You'll be able to

  • Describe direct current as a flow of charge carriers and use I=ΔqΔtI = \frac{\Delta q}{\Delta t}.
  • Define potential difference and use V=WqV = \frac{W}{q}.
  • Explain that a cell is a source of emf, and distinguish emf from potential difference.
  • Compare chemical cells and solar cells as energy sources.
  • Read and draw circuit diagrams, with ammeters and voltmeters in the right places.
Before you start3 quick questions on what this builds on
Check yourself
Convert 45 mA\pu{45 mA} to amperes.
Check yourself
How many seconds are there in 2.52.5 hours?
Check yourself
A force of 20 N\pu{20 N} pushes a box 3.0 m\pu{3.0 m} along the floor, in the direction of the force. Calculate the work done on the box, in joules.

Revise first: 1.9 Work and energy transfer and 6.1 Units, measurement and estimation

Charge and current

comes in two kinds, positive and negative. Like charges repel and unlike charges attract.

Charge is measured in coulombs (C). An electron carries a charge of −e-e, where e=1.60⋅10−19 Ce = \pu{1.60e-19 C}. That value, like every constant here, is in the data booklet.

A is a charged particle that is free to move. In a metal the carriers are free electrons; in a salt solution they are ions.

In the formula booklet
I=ΔqΔtI = \frac{\Delta q}{\Delta t}

Here II is the , Δq\Delta q is the charge that passes a point and Δt\Delta t is the time taken. The unit of current is the ampere (A), an . One ampere is one coulomb per second, so 1 A=1 C s−1\pu{1 A} = \pu{1 C s-1}.

This lesson is about direct current (dc): the carriers drift one way only, so the current never reverses. Cells give dc. Alternating current is not in this course.

Conventional current flows from the positive terminal of the source, round the circuit, to the negative terminal: the way positive charge would move. Electrons in a metal drift the other way, from negative to positive.

A cell and a lamp joined in a loop. The long thin plate of the cell is the positive terminal and the short thick plate is the negative terminal. On the left-hand wire, an arrow labelled conventional current points down, away from the positive terminal. Beside it, an arrow labelled electron flow points up, the opposite way. + − cell lamp conventional current electron flow
Conventional current leaves the positive terminal. Electrons in the wire drift the opposite way.
Worked exampleIn a fan heater, 920 C\pu{920 C} of charge flows through the heating element in 35 minutes. Calculate the average current in the element.

Try it first, then reveal one step at a time.

  1. Convert the time to seconds: Δt=35×60=2100 s\Delta t = 35 \times 60 = \pu{2100 s}.
Worked exampleA small LED carries a steady current of 18 mA\pu{18 mA}. Determine the number of electrons that pass a point in the LED in 45 s\pu{45 s}.

Try it first, then reveal one step at a time.

  1. Find the charge that passes: Δq=IΔt=(18×10−3)(45)=0.81 C\Delta q = I\Delta t = (18 \times 10^{-3})(45) = \pu{0.81 C}.
Check yourself
A lightning stroke transfers 15 C\pu{15 C} of charge in 0.60 ms\pu{0.60 ms}. Calculate the average current, in amperes to 2 significant figures.
Check yourself
A cell lights a lamp through copper wires. Which statement about the wires is correct?

Potential difference

Charge flowing through a lamp gives it energy, which leaves as light and thermal energy. Potential difference measures the energy each coulomb transfers.

In the formula booklet
V=WqV = \frac{W}{q}

Here VV is the (pd), WW is the done, or transferred, and qq is the charge that moves. The unit is the volt (V). One volt is one joule per coulomb, so 1 V=1 J C−1\pu{1 V} = \pu{1 J C-1}.

A pd of 6 V\pu{6 V} across a lamp means each coulomb passing through it transfers 6 J\pu{6 J} of electrical energy to light and thermal energy.

Rearranged, W=qVW = qV, and with q=IΔtq = I\Delta t the energy transferred is W=VIΔtW = VI\Delta t.

Worked exampleWhile a car headlamp is switched on, 150 C\pu{150 C} of charge passes through it and 1800 J\pu{1800 J} of electrical energy is transferred to light and thermal energy. Calculate the potential difference across the headlamp.

Try it first, then reveal one step at a time.

  1. Use V=WqV = \dfrac{W}{q}.
Worked exampleThe pd across an electric motor is 9.0 V\pu{9.0 V}. Outline what this means.

Try it first, then reveal one step at a time.

  1. Name the quantity: work done (energy transferred) per unit charge.
Check yourself
Which is equal to one volt?
Check yourself
In a vacuum tube, an electron is accelerated from rest through a potential difference of 250 V\pu{250 V}. Calculate the kinetic energy it gains, in joules to 2 significant figures.

Cells and emf

A lamp stays lit only while something keeps giving the charge energy. In a torch, chemical reactions in a cell do work on the charge passing through it, so the cell is a source of .

The symbol for emf is ε\varepsilon and, as energy per unit charge, its unit is the volt: ε=Wq\varepsilon = \frac{W}{q}. The name stands for electromotive force, but emf is not a force.

Emf and pd are both energy per unit charge, but the energy goes opposite ways. In a source, other forms of energy become electrical energy: that is emf. In a component such as a lamp, electrical energy becomes other forms: that is pd.

Charge also transfers some energy inside a real cell, which warms it. So the pd across its terminals equals its emf only when no current flows. You will model this with in 2.14.

A battery is two or more cells in series, positive to negative. Their emfs add. A cell put in the wrong way round takes energy back, so its emf subtracts.

Worked exampleA torch battery is made of three cells in series, each of emf 1.5 V\pu{1.5 V}. While the torch is on, 640 C\pu{640 C} of charge passes through the battery. Calculate the energy the battery transfers to electrical energy.

Try it first, then reveal one step at a time.

  1. Add the emfs of the cells in series: ε=3×1.5=4.5 V\varepsilon = 3 \times 1.5 = \pu{4.5 V}.
Worked exampleA cell lights a lamp. Distinguish between the emf of the cell and the potential difference across the lamp.

Try it first, then reveal one step at a time.

  1. Say what the two quantities have in common.
Check yourself
A cell has an emf of 2.0 V\pu{2.0 V}. What does this mean?
Check yourself
Four cells, each of emf 1.2 V\pu{1.2 V}, are placed in series in a holder. One of them is the wrong way round. What is the emf of the combination?

Chemical cells and solar cells

In a chemical cell, reactions at two electrodes in an electrolyte transfer chemical energy to electrical energy. A primary cell is used once. A secondary cell is rechargeable: a current driven backwards through it reverses the reactions.

A cell's capacity is the total charge it can deliver, often in ampere-hours: 1 A h=1×3600=3600 C\pu{1 A h} = 1 \times 3600 = \pu{3600 C}.

A solar (photovoltaic) cell transfers light energy straight to electrical energy. One cell gives only about 0.5 V\pu{0.5 V}, so panels join many together. The output rises and falls with the light intensity.

Chemical cells. For: portable, store energy until it is needed, and give a fairly steady emf; rechargeable ones can be reused. Against: they store limited energy, so they run flat, and their chemicals can be toxic to dispose of.

Solar cells. For: a renewable source, sunlight, with no fuel, no moving parts and no pollution while working. Against: no output at night and less in cloud, so energy must be stored, and a large area is needed for a large power.

Exam answers about sources need physics reasons. Cost is an economic point and earns no marks.

Worked exampleA rechargeable phone battery has an emf of 3.8 V\pu{3.8 V} and a capacity of 3200 mA h\pu{3200 mA h}. Assuming the emf stays constant, determine the energy it can transfer to electrical energy from fully charged.

Try it first, then reveal one step at a time.

  1. Convert the capacity to coulombs: q=(3200×10−3 A)×(3600 s)=11520 Cq = (3200 \times 10^{-3}\ \text{A}) \times (3600\ \text{s}) = \pu{11520 C}.
Worked exampleA weather station on a remote mountain is powered by solar cells. Outline one advantage and one disadvantage of using solar cells rather than chemical cells alone for this.

Try it first, then reveal one step at a time.

  1. Advantage: name the energy source and what it means for this site.
Check yourself
Which is a valid physics advantage of a solar cell over a chemical cell?

Circuit diagrams and meters

A circuit diagram shows how components are connected, not where they sit on the bench. Each component has a standard symbol; lines are wires of negligible resistance.

The symbols you need are in the data booklet. The LDR, thermistor and potentiometer come back in 2.14.

Twelve circuit symbols in a grid. Cell: a long thin plate beside a short thick plate. Battery: two cells joined by a dashed line. Open switch: a hinged line lifted away from a contact. Lamp: a circle with a cross inside. Resistor: a rectangle. Variable resistor: a rectangle with a diagonal arrow through it. Ammeter: a circle with A inside. Voltmeter: a circle with V inside. LDR: a rectangle with two arrows pointing in towards it. Thermistor: a rectangle crossed by a diagonal line with a short flat tail at its lower end. Potentiometer: a rectangle with an arrow pointing onto its middle from below. LED: a diode triangle and bar with two arrows pointing outwards. cell battery switch (open) lamp resistor variable resistor A ammeter V voltmeter LDR thermistor potentiometer LED
Some of the data booklet symbols. The booklet also shows the heating element, motor and earth. The long thin plate of a cell is its positive terminal.

A current flows only round a complete loop. In a single loop, a series circuit, the same current passes every point. Charge is not used up in a lamp; what the lamp takes from the charge is energy.

An ammeter goes in series with the component, so all its charge flows through the meter. A voltmeter measures the pd between two points, so it goes in parallel, one lead on each side of the component.

A single loop containing a cell, a switch, a lamp and an ammeter, all in series. The cell and the switch are on the top wire, the ammeter is on the right-hand wire and the lamp is on the bottom wire. A voltmeter sits on a separate branch below the lamp: its two wires join the main loop on either side of the lamp, at two junction dots, so the voltmeter is in parallel across the lamp. A V cell switch lamp ammeter: in series voltmeter: in parallel across the lamp
The ammeter is in the loop. The voltmeter bridges the lamp.

An ideal ammeter has zero resistance, so it does not reduce the current. An ideal voltmeter has infinite resistance, so no current flows through it. Meters are ideal unless a question says otherwise.

Worked exampleA student wants to measure the current in a heating element and the pd across it. Describe how the ammeter and the voltmeter should be connected, and explain why each meter should be ideal.

Try it first, then reveal one step at a time.

  1. Place each meter and give the reason for its position.
Worked exampleTwo ideal ammeters are in series with a lamp, one on each side of it. A student predicts the second will read less, because the lamp uses up some current. Explain why the readings are equal.

Try it first, then reveal one step at a time.

  1. Start from what current is.
Check yourself
How is an ammeter connected to measure the current in a resistor, and what is the resistance of an ideal ammeter?
Check yourself
In a series circuit, an ammeter beside the cell reads 0.35 A\pu{0.35 A}. Calculate the charge that flows through a lamp on the far side of the loop in 2.0 minutes, in coulombs to 2 significant figures.

Common mistakes

  • Defining emf as the pd across the cell's terminals. Give the energy transferred to electrical energy per unit charge by the source.
  • Leaving time in minutes or current in mA in I=ΔqΔtI = \frac{\Delta q}{\Delta t}. Convert to seconds and amperes first.
  • Saying a lamp uses up current. Charge is conserved; the lamp takes energy.
  • Putting the voltmeter in series or the ammeter in parallel.
  • Giving cost as an advantage of solar cells. Give a physics point instead.

Exam tips

  • "State what is meant by" emf: you need "per unit charge" and the energy change (other forms to electrical, in the source).
  • "Calculate" or "determine": write the booklet equation, substitute in SI units and give the unit. In a "deduce", a bald answer can score zero.
  • "Outline" an advantage of a source (Paper 2): one physics point and what it means in context. Economic reasons get no credit.
  • Paper 1A tests units: 1 V=1 J C−1\pu{1 V} = \pu{1 J C-1}, 1 A=1 C s−1\pu{1 A} = \pu{1 C s-1}, 1 A h=3600 C\pu{1 A h} = \pu{3600 C}.

Key takeaways

In bookletI=ΔqΔtI = \frac{\Delta q}{\Delta t}
In bookletV=WqV = \frac{W}{q}
Learn this1 A=1 C s−1\pu{1 A} = \pu{1 C s-1}, 1 V=1 J C−1\pu{1 V} = \pu{1 J C-1} and 1 A h=3600 C\pu{1 A h} = \pu{3600 C}. Electron charge: −e-e, with e=1.60⋅10−19 Ce = \pu{1.60e-19 C}.
Learn thisEmf ε\varepsilon: energy transferred to electrical energy per unit charge by a source. Pd: electrical energy transferred to other forms per unit charge between two points. Terminal pd equals ε\varepsilon only when no current flows.
Learn thisConventional current flows from + to − outside the source; electrons in a metal drift the other way. Charge is never used up.
Learn thisAmmeter in series (ideal: zero resistance). Voltmeter in parallel (ideal: infinite resistance).
Learn thisChemical cell: chemical to electrical, portable, limited store. Solar cell: light to electrical, renewable, no emissions, no output in the dark.

Practise this

94 past-paper questions on Current, resistance, circuits and heating in the Physics HL bank, each with a mark scheme and a worked explanation.

Practise Current, resistance, circuits and heating →