2.14 · SLPaper 1Paper 2

Electrical power and circuits

In a minute

A resistor dissipates energy as heat at a rate called , P=IVP = IV. Resistors combine in series and parallel by simple rules. A real cell's makes the (pd) it delivers less than its . and change with temperature and light, so they make good sensors.

You'll be able to

  • Calculate the electrical power and energy dissipated in a resistor.
  • Combine resistors in series and parallel, and find the current and pd in each.
  • Explain how currents and pds change when a branch is added.
  • Use ε=I(R+r)\varepsilon = I(R + r), and explain why the terminal pd falls as the current rises.
  • Describe thermistors, LDRs and potentiometers, and use them in potential dividers.
Before you start3 quick questions on what this builds on
Check yourself
A charge of 36 C\pu{36 C} passes a point in a wire in 1.5 min\pu{1.5 min}. What is the in the wire, in A? Give 2 significant figures.
Check yourself
A resistor has a pd of 4.8 V\pu{4.8 V} across it and a current of 0.24 A\pu{0.24 A} in it. What is its resistance?
Check yourself
A lamp transfers 540 J\pu{540 J} of energy in one minute. What is its ?

Revise first: 1.11 Power, efficiency and energy density, 2.12 Current, potential difference and emf and 2.13 Resistance, resistivity and Ohm's law

Power dissipated in a resistor

Each passing through a resistor loses electrical potential energy, and the resistor warms up. The rate of this transfer is the dissipated.

The VV is the energy transferred per coulomb, and the II is the coulombs per second. So the energy per second is VIVI.

Put V=IRV = IR into P=IVP = IV to get P=I2RP = I^2R, or I=VRI = \frac{V}{R} to get P=V2RP = \frac{V^2}{R}.

In the formula booklet
P=IV=I2R=V2RP = IV = I^{2}R = \frac{V^{2}}{R}

Pick the form that uses the two quantities you know. The equations in this lesson are in section B.5 of the data booklet unless tagged learn.

A metal at constant temperature obeys , so RR is fixed and P∝V2P \propto V^2. A filament lamp's resistance rises as it heats, so use its value at the working current.

Energy transferred in time tt (in seconds) at a steady power: E=PtE = Pt.

Worked exampleThe heating element of a car's rear-window demister is connected to a 12.0 V\pu{12.0 V} dc supply. It dissipates 96.0 W\pu{96.0 W}. Calculate the resistance of the element.

Try it first, then reveal one step at a time.

  1. You know VV and PP, so rearrange P=V2RP = \frac{V^2}{R}: R=V2PR = \frac{V^2}{P}.
Worked exampleA 72 Ω72\ \Omega resistor carries a steady current of 0.25 A\pu{0.25 A} for 3.0 min\pu{3.0 min}. Calculate the energy dissipated in the resistor.

Try it first, then reveal one step at a time.

  1. You know II and RR, so use P=I2R=0.252×72=4.5 WP = I^2R = 0.25^2 \times 72 = \pu{4.5 W}.
Check yourself
The pd across an ohmic resistor at constant temperature is doubled. What happens to the power it dissipates?
Check yourself
A torch bulb works at 4.5 V\pu{4.5 V} and dissipates 2.7 W\pu{2.7 W}. What is the current in it, in A? Give 2 significant figures.

Resistors in series and in parallel

A series circuit has one path, and charge is never used up (). So the current is the same at every point.

Each coulomb's energy is shared between the components, so their pds add up to the supply pd. Each pd is IRIR with the same II, so add too.

In a parallel circuit, branches connect the same two points, so each has the same pd. The branch currents add up to the current into the junction.

Write I=VRI = \frac{V}{R} for each branch and divide by VV: 1Rp=1R1+1R2+…\frac{1}{R_\text{p}} = \frac{1}{R_1} + \frac{1}{R_2} + \dots

Two circuits side by side. Left, series: a cell on the top wire and two resistors, R1 and R2, one after the other on the bottom wire, so there is a single loop and the same current I passes through both. Right, parallel: a cell on the top wire and two branches between the same two junctions, R1 on the upper branch and R2 on the lower branch; the current I splits at the left junction into I1 and I2, which rejoin at the right junction. Series Parallel I R1 R2 I I1 I2 R1 R2 one path: same current in each resistor pds add: V = V1 + V2 same pd across each branch currents add: I = I1 + I2
Series: one current, shared pd. Parallel: one pd, shared current.
In the formula booklet
Series: I=I1=I2=…V=V1+V2+…Rs=R1+R2+…\text{Series: } I = I_{1} = I_{2} = \dots \qquad V = V_{1} + V_{2} + \dots \qquad R_\text{s} = R_{1} + R_{2} + \dots
In the formula booklet
Parallel: I=I1+I2+…V=V1=V2=…1Rp=1R1+1R2+…\text{Parallel: } I = I_{1} + I_{2} + \dots \qquad V = V_{1} = V_{2} = \dots \qquad \frac{1}{R_\text{p}} = \frac{1}{R_{1}} + \frac{1}{R_{2}} + \dots

nn equal resistors RR in parallel combine to Rn\frac{R}{n}.

Treat meters as ideal unless told otherwise. An ideal ammeter has zero resistance; an ideal voltmeter has infinite resistance and draws no current. A non-ideal meter is just one more constant resistor.

For a network: combine each parallel group, add the series parts, find the supply current, then work back with V=IRV = IR.

Worked exampleFind the current drawn from a 4.8 V\pu{4.8 V} battery (negligible internal resistance) when 30 Ω30\ \Omega and 20 Ω20\ \Omega resistors are placed side by side across it.

Try it first, then reveal one step at a time.

  1. Combined resistance: 1Rp=130+120=2+360=560\frac{1}{R_\text{p}} = \frac{1}{30} + \frac{1}{20} = \frac{2 + 3}{60} = \frac{5}{60}, so Rp=12 ΩR_\text{p} = 12\ \Omega.
Worked exampleA 12 Ω12\ \Omega resistor is connected in series with a parallel pair made of a 40 Ω40\ \Omega and a 10 Ω10\ \Omega resistor. The combination is connected to an 8.0 V\pu{8.0 V} battery of negligible internal resistance. Determine the power dissipated in the 40 Ω40\ \Omega resistor.

Try it first, then reveal one step at a time.

  1. Parallel pair: 1Rp=140+110=540\frac{1}{R_\text{p}} = \frac{1}{40} + \frac{1}{10} = \frac{5}{40}, so Rp=8.0 ΩR_\text{p} = 8.0\ \Omega.
Worked exampleTwo identical lamps, L1 and L2, are connected in parallel to a battery of negligible internal resistance. A third identical lamp is then connected in parallel with them. Explain what happens to the brightness of L1 and to the current in the battery.

Try it first, then reveal one step at a time.

  1. Use what parallel branches share, then the total resistance.
Check yourself
Resistors of 8.0 Ω8.0\ \Omega, 24 Ω24\ \Omega and 12 Ω12\ \Omega are connected in parallel. What is their combined resistance?
Check yourself
A 2.2 kΩ\pu{2.2 k\Omega} resistor and a 3.3 kΩ\pu{3.3 k\Omega} resistor are connected in series to an 11 V\pu{11 V} supply of negligible internal resistance. What is the pd across the 3.3 kΩ\pu{3.3 k\Omega} resistor, in V? Give 2 significant figures.

Emf and internal resistance

The ε\varepsilon of a cell is the energy it transfers to each coulomb passing through it (2.12). A real cell can't pass all of it on.

The chemicals inside the cell have , so some energy per coulomb is dissipated inside the cell itself.

A real cell drawn as a dashed box containing an ideal cell of emf epsilon in series with a small resistor r, the internal resistance. The two terminals are dots on the edges of the box. Outside the box, a single loop runs through an ammeter on the right-hand wire and an external resistor R on the bottom wire. A voltmeter is connected across the two terminals, so it reads the terminal potential difference V. V A ε r R voltmeter reads the terminal pd V real cell (between the terminals) energy per coulomb: ε = IR + Ir, so V = IR = ε − Ir
Model a real cell as an ideal emf ε\varepsilon in series with its internal resistance rr.

The same current passes through RR and rr, so the emf is shared: IRIR outside and IrIr inside.

In the formula booklet
ε=I(R+r)\varepsilon = I(R + r)

The is the part outside, V=IRV = IR, so:

Learn this
V=ε−IrV = \varepsilon - Ir

IrIr is the “lost volts”. With no current, V=εV = \varepsilon; the bigger the current, the smaller VV.

A short circuit (R≈0R \approx 0) gives the largest current, I=εrI = \frac{\varepsilon}{r}, and the cell can get dangerously hot.

To measure ε\varepsilon and rr, vary RR and plot VV against II: a straight line, V=−rI+εV = -rI + \varepsilon.

Worked exampleA 2.4 Ω2.4\ \Omega resistor is joined across a battery whose emf is 4.5 V\pu{4.5 V} and whose internal resistance is 0.60 Ω0.60\ \Omega. Calculate the terminal pd.

Try it first, then reveal one step at a time.

  1. Current: I=εR+r=4.52.4+0.60=4.53.0=1.5 AI = \frac{\varepsilon}{R + r} = \frac{4.5}{2.4 + 0.60} = \frac{4.5}{3.0} = \pu{1.5 A}.
Worked exampleWith nothing else connected, an ideal voltmeter across a battery reads 4.50 V\pu{4.50 V}. A 12.0 Ω12.0\ \Omega resistor is then connected across the battery, and the voltmeter reading falls to 4.05 V\pu{4.05 V}. Determine the internal resistance of the battery.

Try it first, then reveal one step at a time.

  1. No current flows at first, so ε=4.50 V\varepsilon = \pu{4.50 V}.
Worked exampleAn ideal voltmeter is connected across a cell that has internal resistance and is supplying a resistor. Another resistor is added in parallel with that one. Explain the change in the voltmeter reading.

Try it first, then reveal one step at a time.

  1. Follow the chain: external resistance, current, IrIr, terminal pd.

As energy sources, cells are portable, give direct current at once and release no emissions where used. Rechargeable cells can be reused.

But they store little energy per kilogram compared with fuels, and internal resistance limits the current and wastes energy. Their emf falls as they run down, and used cells need careful disposal.

Check yourself
A 1.5 V\pu{1.5 V} cell with internal resistance 0.30 Ω0.30\ \Omega is short-circuited by a thick wire of negligible resistance. What is the current, in A? Give 2 significant figures.
Check yourself
A student plots terminal pd VV against current II for a cell, varying the external resistance. What do the VV-intercept and the gradient give?

Variable resistors and potential dividers

You need three variable resistors: the , the (LDR) and the potentiometer. Their symbols are in the data booklet.

Heating the thermistor's semiconductor frees more , so its falls, though not in inverse proportion to temperature.

Its resistance depends on temperature, and the current in it can heat it, so it is a .

In an LDR, light frees the charge carriers instead.

Two resistors in series share the supply pd in the ratio of their resistances, since the same current passes through both. This is a potential divider.

Learn this
Vout=Vin R2R1+R2V_\text{out} = V_\text{in}\,\frac{R_{2}}{R_{1} + R_{2}}

This assumes negligible internal resistance and nothing drawing current from the output.

Potential divider. A supply of potential difference V in, with negligible internal resistance, on the left. On the right, a fixed resistor R1 on top and a thermistor R2 below it are joined in series between the top and bottom wires. Output wires run from the junction between them and from the bottom wire to two open terminals, so the output potential difference V out is the pd across the thermistor. + Vin fixed resistor R1 thermistor R2 Vout same current in R1 and R2, so the pd divides in the ratio R1 : R2
As the NTC thermistor warms, R2R_2 falls, so it takes a smaller share of VinV_\text{in} and VoutV_\text{out} falls.

With a thermistor or LDR as R2R_2, the output pd follows temperature or light: a sensor circuit.

A potentiometer is a resistor track with a sliding contact: an adjustable potential divider. Its output can be set anywhere from zero to the full supply pd.

Worked exampleAn NTC thermistor and a fixed 1.5 kΩ\pu{1.5 k\Omega} resistor are connected in series to a 6.0 V\pu{6.0 V} battery of negligible internal resistance. At room temperature the thermistor's resistance is 3.5 kΩ\pu{3.5 k\Omega}. Calculate the pd across the fixed resistor.

Try it first, then reveal one step at a time.

  1. Total resistance: 1.5+3.5=5.0 kΩ1.5 + 3.5 = \pu{5.0 k\Omega}.
Worked exampleAn LDR and a fixed resistor are connected in series to a battery of negligible internal resistance. A voltmeter is connected across the fixed resistor. Explain what happens to the voltmeter reading when the light falling on the LDR becomes brighter.

Try it first, then reveal one step at a time.

  1. Chain: LDR, total resistance, current, pd across the fixed resistor.
Check yourself
An NTC thermistor is in series with a fixed resistor across a battery of negligible internal resistance. The thermistor warms up. What happens to the pd across the thermistor?
Check yourself
In the circuit of the example above (6.0 V\pu{6.0 V} battery, fixed 1.5 kΩ\pu{1.5 k\Omega} resistor), the thermistor warms until the pd across the fixed resistor is 4.2 V\pu{4.2 V}. What is the thermistor's resistance now, in Ω\Omega? Give 2 significant figures.
Check yourself
A uniform potentiometer track is across a 10 V\pu{10 V} battery (negligible internal resistance). The slider is a quarter of the way from the negative end. What does an ideal voltmeter between the slider and that end read, in V? Give 2 significant figures.

Common mistakes

  • Saying current is used up in a resistor. Current is the same all round a series circuit; energy is what is transferred.
  • Using the whole supply pd for one resistor in series, for example in P=V2RP = \frac{V^2}{R}. Use that resistor's own pd.
  • Adding resistances in parallel, or forgetting to invert 1Rp\frac{1}{R_\text{p}}. A parallel combination is always smaller than its smallest resistor.
  • Defining emf as the pd across the cell's terminals. Emf is the energy the cell transfers per unit charge; the terminal pd is less by IrIr whenever current flows.
  • Calling an NTC thermistor's resistance inversely proportional to temperature. It decreases as temperature rises, but not in proportion.

Exam tips

  • “Explain” a change in a meter reading: give the chain, one link per sentence: resistance, current, pd, reading. A bald “it increases” earns nothing.
  • “Show that”: write the equation and substitution, and give one more significant figure than the stated value.
  • Advantages and disadvantages of cells: give physics reasons (portability, no emissions where used, internal resistance, stored energy). Cost earns no marks.
  • In Paper 1A, use limits: a parallel combination is below its smallest resistor, and while a cell supplies current, its terminal pd is less than its emf.

Key takeaways

In bookletP=IV=I2R=V2RP = IV = I^{2}R = \frac{V^{2}}{R}
In bookletSeries: I=I1=I2=…V=V1+V2+…Rs=R1+R2+…\text{Series: } I = I_{1} = I_{2} = \dots \qquad V = V_{1} + V_{2} + \dots \qquad R_\text{s} = R_{1} + R_{2} + \dots
In bookletParallel: I=I1+I2+…V=V1=V2=…1Rp=1R1+1R2+…\text{Parallel: } I = I_{1} + I_{2} + \dots \qquad V = V_{1} = V_{2} = \dots \qquad \frac{1}{R_\text{p}} = \frac{1}{R_{1}} + \frac{1}{R_{2}} + \dots
Learn thisResistors in parallel combine to less than the smallest of them. An ideal ammeter has zero resistance; an ideal voltmeter has infinite resistance.
In bookletε=I(R+r)\varepsilon = I(R + r)
Learn thisTerminal pd V=ε−IrV = \varepsilon - Ir. It equals the emf only when no current flows, and falls as the current rises.
Learn thisNTC thermistor: resistance falls as temperature rises. LDR: resistance falls as light intensity rises. Potential divider: Vout=Vin R2R1+R2V_\text{out} = V_\text{in}\,\frac{R_2}{R_1 + R_2}; a potentiometer gives any output from zero to VinV_\text{in}.

Practise this

94 past-paper questions on Current, resistance, circuits and heating in the Physics HL bank, each with a mark scheme and a worked explanation.

Practise Current, resistance, circuits and heating →