2.11 · AHL · HL onlyPaper 1Paper 2

Gas processes and heat engines

In a minute

A gas can change state while one thing stays fixed: its volume, its pressure, its temperature or, in an change, its heat exchange. Take a gas round a closed loop of such changes and you have a , turning thermal energy into work again and again. The sets the highest any engine can reach between two temperatures.

You'll be able to

  • Describe , , and adiabatic processes, and apply the to each one on a .
  • Use PV53=constantPV^{\frac{5}{3}} = \text{constant} to find the pressure, volume and temperature after an adiabatic change of a monatomic .
  • Explain how a cyclic gas process runs a heat engine, and find the net work from the area enclosed on a P-V diagram.
  • Calculate the efficiency of a heat engine running on a given cycle, using η=useful workinput energy\eta = \frac{\text{useful work}}{\text{input energy}}.
  • Use ηCarnot=1−TcTh\eta_\text{Carnot} = 1 - \frac{T_\text{c}}{T_\text{h}} to find the maximum efficiency between two reservoirs, and explain why real engines fall short of it.
Before you start3 quick questions on what this builds on
Check yourself
A gas is supplied with 750 J\pu{750 J} of thermal energy and does 280 J\pu{280 J} of work on its surroundings. Calculate the change in its internal energy, in J.
Check yourself
A gas at a constant pressure of 1.5⋅105 Pa\pu{1.5e5 Pa} expands from 2.0⋅10−3 m3\pu{2.0e-3 m3} to 2.6⋅10−3 m3\pu{2.6e-3 m3}. How much work does the gas do?
Check yourself
The temperature of 0.60 mol\pu{0.60 mol} of an ideal monatomic gas rises by 25 K\pu{25 K}. Calculate the increase in its internal energy, in J to 2 significant figures.

Revise first: 1.11 Power, efficiency and energy density, 2.7 Pressure, amount of substance and the ideal gas model, 2.8 The ideal gas equations and the kinetic model, 2.9 The first law of thermodynamics and 2.10 Entropy and the second law

Four simple gas processes

In 2.9 you met the for a closed system: a fixed amount of gas that exchanges energy with its surroundings, but not matter. Every problem uses the same sign convention.

QQ is the thermal energy supplied to the gas. It is negative when energy leaves the gas as heat.

WW is the work done by the gas. It is positive when the gas expands and negative when the gas is compressed.

In the formula booklet
Q=ΔU+WQ = \Delta U + W

For a monatomic , the depends only on the temperature. So ΔU\Delta U is positive when the gas warms and negative when it cools. All constants in this lesson, such as R=8.31 J K−1 mol−1R = \pu{8.31 J K-1 mol-1}, come from the data booklet.

In the formula booklet
ΔU=32nRΔT=32NkBΔT\Delta U = \frac{3}{2}nR\Delta T = \frac{3}{2}Nk_\text{B}\Delta T

The state of a gas is described by PP, VV and TT, linked by the PV=nRTPV = nRT. Four simple processes each keep one quantity fixed.

1. An keeps VV fixed. The gas pushes nothing back, so W=0W = 0 and Q=ΔUQ = \Delta U.

2. An keeps PP fixed. The work done by the gas is W=PΔVW = P\Delta V.

3. An keeps TT fixed. For an ideal gas this means ΔU=0\Delta U = 0, so Q=WQ = W. All the heat supplied becomes work, or all the work done on the gas leaves it as heat.

4. An keeps QQ fixed at zero: no thermal energy enters or leaves, so ΔU=−W\Delta U = -W. It happens when the gas is insulated, or when the change is too fast for heat to flow.

In the formula booklet
W=PΔVW = P\Delta V

On a , each point is one state of the gas and each line is a process. Here are the four processes, all starting from the same state.

Pressure against volume for a fixed amount of ideal gas. Four lines start from the same state S. A vertical line rises from S, labelled isovolumetric, V constant. A horizontal line runs to the right from S, labelled isobaric, P constant. Two curves fall to the right from S: the gentler one is labelled isothermal, T constant, and the steeper one, which ends lower, is labelled adiabatic, Q equals 0. S isovolumetric (V constant) isobaric (P constant) isothermal (T constant) adiabatic (Q = 0) P V 0
From the same state S: vertical is isovolumetric, horizontal is isobaric, and the adiabatic curve falls more steeply than the isothermal one.

The work done by the gas is the area under its line. Moving right (expansion), the gas does positive work. Moving left (compression), WW is negative: work is done on the gas. A vertical line has no area under it, so W=0W = 0.

Worked exampleHelium in a cylinder is held at 1.6⋅105 Pa\pu{1.6e5 Pa} by a freely sliding piston. Treat it as an ideal monatomic gas. When the helium is heated, its volume increases from 2.5⋅10−3 m3\pu{2.5e-3 m3} to 3.7⋅10−3 m3\pu{3.7e-3 m3}. Determine the thermal energy supplied to the helium.

Try it first, then reveal one step at a time.

  1. Work done by the gas at constant pressure: W=PΔV=(1.6×105)(3.7×10−3−2.5×10−3)=192 JW = P\Delta V = (1.6 \times 10^{5})(3.7 \times 10^{-3} - 2.5 \times 10^{-3}) = \pu{192 J}.
Worked exampleAn ideal gas in a cylinder is compressed slowly, so that its temperature stays constant. Explain, using the first law of thermodynamics, whether thermal energy enters or leaves the gas.

Try it first, then reveal one step at a time.

  1. Say what a constant temperature means for ΔU\Delta U.
Check yourself
A sealed, rigid steel can holds 0.040 mol\pu{0.040 mol} of argon, an ideal monatomic gas. It is warmed from 290 K\pu{290 K} to 365 K\pu{365 K}. Calculate the thermal energy supplied, in J to 2 significant figures.
Check yourself
In which process is the thermal energy supplied to an ideal gas equal to the work done by the gas?

Adiabatic changes

In an expansion no heat enters, but the gas still does work as it pushes outwards. That energy must come from the gas itself. So ΔU=−W\Delta U = -W is negative, and the gas cools.

An adiabatic compression does the reverse. Work is done on the gas (W<0W < 0), so ΔU>0\Delta U > 0 and the gas warms. This is how a diesel engine ignites its fuel without a spark: compressing the air makes it hot enough.

As a gas expands adiabatically, it moves onto cooler and cooler isotherms. So its curve on a is steeper than the isotherm through the same point. The pressure falls both because the volume grows and because the temperature drops.

In the formula booklet
PV53=constantPV^{\frac{5}{3}} = \text{constant}

This model is for a monatomic changing adiabatically, with the same pressure throughout the gas at each moment. Between two states, P1V153=P2V253P_1V_1^{\frac{5}{3}} = P_2V_2^{\frac{5}{3}}. Use PV=nRTPV = nRT alongside it to find a temperature.

Worked exampleNeon, an ideal monatomic gas, is at a pressure of 1.05⋅105 Pa\pu{1.05e5 Pa} in a volume of 6.0⋅10−4 m3\pu{6.0e-4 m3}. It is compressed adiabatically to a volume of 1.5⋅10−4 m3\pu{1.5e-4 m3}. Calculate its final pressure.

Try it first, then reveal one step at a time.

  1. For an adiabatic change, P1V153=P2V253P_1V_1^{\frac{5}{3}} = P_2V_2^{\frac{5}{3}}, so P2=P1(V1V2)53P_2 = P_1\left(\dfrac{V_1}{V_2}\right)^{\frac{5}{3}}.
Worked exampleA sample of 0.25 mol\pu{0.25 mol} of helium, an ideal monatomic gas, is at 420 K\pu{420 K} in a volume of 3.0⋅10−3 m3\pu{3.0e-3 m3}. It expands adiabatically to a volume of 7.5⋅10−3 m3\pu{7.5e-3 m3}. Determine the work done by the gas.

Try it first, then reveal one step at a time.

  1. Starting pressure: P1=nRT1V1=(0.25)(8.31)(420)3.0×10−3=2.91⋅105 PaP_1 = \dfrac{nRT_1}{V_1} = \dfrac{(0.25)(8.31)(420)}{3.0 \times 10^{-3}} = \pu{2.91e5 Pa}.
Check yourself
A monatomic ideal gas expands adiabatically. What happens to its temperature?
Check yourself
Argon, an ideal monatomic gas, is at 2.4⋅105 Pa\pu{2.4e5 Pa} in a volume of 1.8⋅10−3 m3\pu{1.8e-3 m3}. It expands adiabatically until its pressure is 6.0⋅104 Pa\pu{6.0e4 Pa}. Calculate its final volume, in units of 10−3 m310^{-3}\ \text{m}^{3}, to 2 significant figures.

Cycles and heat engines

One expansion can do work only once: the piston soon reaches the end of the cylinder. To keep doing work, the gas must be brought back to its starting state and the process repeated. A series of processes that ends where it began is called a cycle.

After a full cycle the gas is back at its starting temperature, so ΔU=0\Delta U = 0. The first law then says that the net thermal energy taken in over the cycle equals the net work done by the gas.

On a a cycle is a closed loop, and the net work is the area it encloses. Going clockwise, the gas expands at a higher pressure than it is compressed at, so net work is done by the gas. Going anticlockwise, net work is done on the gas.

A runs a gas round such a cycle. In each cycle it takes in thermal energy QhQ_\text{h} from a hot reservoir, does useful work WW, and gives out thermal energy QcQ_\text{c} to a cold reservoir. Here QhQ_\text{h} and QcQ_\text{c} are sizes, both positive.

Energy flow in a heat engine. A box at the top is labelled hot reservoir at temperature T h. A thick arrow labelled Q h goes down from it into a circle labelled engine. An arrow labelled W, useful work, leaves the engine to the right. An arrow labelled Q c goes down from the engine into a box at the bottom labelled cold reservoir at temperature T c. hot reservoir, temperature Th cold reservoir, temperature Tc engine Qh Qc W useful work
Energy flow in one cycle: Qh=W+QcQ_\text{h} = W + Q_\text{c}.

The Kelvin form of the , from 2.10, says no cyclic engine can turn all of QhQ_\text{h} into work. Some energy must always go to the cold reservoir, so Qc>0Q_\text{c} > 0.

Engines run on many different cycles. A petrol engine roughly follows two adiabatic and two isovolumetric stages; other designs use isobaric or isothermal stages. Each cycle gives a different efficiency, but you work it out the same way.

The of an engine compares the useful work it does with the energy put in. For a heat engine, the input energy is QhQ_\text{h}, the thermal energy taken in.

In the formula booklet
η=useful workinput energy\eta = \frac{\text{useful work}}{\text{input energy}}

So η=WQh=Qh−QcQh\eta = \dfrac{W}{Q_\text{h}} = \dfrac{Q_\text{h} - Q_\text{c}}{Q_\text{h}}. For a cycle on a P-V diagram, WW is the enclosed area. QhQ_\text{h} is the sum of the positive values of QQ only, from the stages where heat flows in.

Worked exampleIn each cycle, the engine of a small generator takes in 2.60 kJ\pu{2.60 kJ} of thermal energy from burning fuel and gives out 1.85 kJ\pu{1.85 kJ} to the surrounding air. Calculate the efficiency of the engine.

Try it first, then reveal one step at a time.

  1. Useful work per cycle: W=Qh−Qc=2.60−1.85=0.75 kJW = Q_\text{h} - Q_\text{c} = 2.60 - 1.85 = \pu{0.75 kJ}.

In a cycle made of several processes, find QQ for each stage from the first law. Only the stages where QQ is positive count towards the input energy.

Pressure in units of 10 to the 5 pascals against volume in units of 10 to the minus 3 cubic metres. A rectangle has corners A at volume 1.6 and pressure 1.4, B at volume 1.6 and pressure 4.2, C at volume 3.8 and pressure 4.2, and D at volume 3.8 and pressure 1.4. Arrows go clockwise: up from A to B, right from B to C, down from C to D and left from D to A. The inside of the rectangle is shaded. A B C D 1.4 4.2 1.6 3.8 P / 10⁵ Pa V / 10⁻³ m³ 0
The cycle ABCDA for the next example. The shaded area is the net work done by the gas.
Worked exampleAn ideal monatomic gas is taken round the cycle ABCDA in the diagram. A to B and C to D are isovolumetric; B to C and D to A are isobaric. Determine the efficiency of this cycle.

Try it first, then reveal one step at a time.

  1. Net work is the enclosed area: W=(4.2−1.4)×105×(3.8−1.6)×10−3=(2.8×105)(2.2×10−3)=616 JW = (4.2 - 1.4) \times 10^{5} \times (3.8 - 1.6) \times 10^{-3} = (2.8 \times 10^{5})(2.2 \times 10^{-3}) = \pu{616 J}.
Check yourself
A car engine has an efficiency of 0.31 and a useful power output of 42 kW\pu{42 kW}. Calculate the rate at which it transfers thermal energy to the surroundings, in kW to 2 significant figures.
Check yourself
A gas is taken anticlockwise round a closed loop on a P-V diagram. Which statement about one complete cycle is correct?

The Carnot cycle and the efficiency limit

Every heat engine wastes some heat. How small can the wasted fraction be? The answer depends only on the temperatures of the two reservoirs, and the reaches it.

A Carnot engine takes an ideal gas through four reversible stages:

1. A to B: isothermal expansion at ThT_\text{h}. The gas takes in QhQ_\text{h} from the hot reservoir.

2. B to C: adiabatic expansion. The gas does work and cools from ThT_\text{h} to TcT_\text{c}.

3. C to D: isothermal compression at TcT_\text{c}. The gas gives out QcQ_\text{c} to the cold reservoir.

4. D to A: adiabatic compression. Work done on the gas warms it back to ThT_\text{h}.

Pressure against volume for a Carnot cycle. From A at the top left, the gas expands along the hotter isotherm, labelled T h, to B, taking in thermal energy Q h. From B it expands along a steeper adiabatic curve down to C. From C it is compressed along the cooler isotherm, labelled T c, to D, giving out thermal energy Q c. From D a steep adiabatic curve rises back to A. The cycle runs clockwise and the enclosed area is shaded. A B C D Th, takes in Qh Tc, gives out Qc adiabatic adiabatic P V 0
A Carnot cycle: two isotherms joined by two steeper adiabatics, run clockwise. The shaded area is the net work.

Heat flows only while the gas is at (almost exactly) the reservoir's temperature, so no heat crosses a real temperature difference. With no friction either, every stage is reversible, with no losses. Over a cycle, the total of the gas and the two reservoirs does not change.

This gives the limit. The hot reservoir loses entropy QhTh\frac{Q_\text{h}}{T_\text{h}} and the cold one gains QcTc\frac{Q_\text{c}}{T_\text{c}}. With no overall change these are equal, so QcQh=TcTh\frac{Q_\text{c}}{Q_\text{h}} = \frac{T_\text{c}}{T_\text{h}} and η=1−QcQh=1−TcTh\eta = 1 - \frac{Q_\text{c}}{Q_\text{h}} = 1 - \frac{T_\text{c}}{T_\text{h}}.

In the formula booklet
ηCarnot=1−TcTh\eta_\text{Carnot} = 1 - \frac{T_\text{c}}{T_\text{h}}

Both temperatures must be in kelvin. No heat engine working between the same two reservoirs can be more efficient than a Carnot engine. A more efficient one would send less heat to the cold reservoir, so the total entropy would fall, which the forbids.

Real engines fall well short of the Carnot efficiency. They have friction and turbulence, and their heat flows across real temperature differences, which is irreversible. A true Carnot cycle would also have to run infinitely slowly, so it would deliver no power. It is a theoretical limit, not a practical design.

To raise the limit, make ThT_\text{h} higher or TcT_\text{c} lower. This is why power stations run their steam as hot as their materials allow.

Worked exampleThe turbines of a power station take in steam at 540 ∘C540\,^{\circ}\text{C} and release heat to cooling water at 25 ∘C25\,^{\circ}\text{C}. Calculate the maximum possible efficiency of the turbines.

Try it first, then reveal one step at a time.

  1. Convert to kelvin: Th=540+273=813 KT_\text{h} = 540 + 273 = \pu{813 K} and Tc=25+273=298 KT_\text{c} = 25 + 273 = \pu{298 K}.
Worked exampleAn inventor claims that her engine takes in 5.0 kJ\pu{5.0 kJ} of thermal energy per cycle from a reservoir at 640 K\pu{640 K}, gives out heat to the air at 290 K\pu{290 K}, and does 3.0 kJ\pu{3.0 kJ} of work per cycle. Evaluate this claim.

Try it first, then reveal one step at a time.

  1. Work out the efficiency she claims.
Check yourself
A Carnot engine works between reservoirs at 177 ∘C177\,^{\circ}\text{C} and 27 ∘C27\,^{\circ}\text{C}. What is its efficiency?
Check yourself
A Carnot engine has an efficiency of 0.35. Its cold reservoir is at 17 ∘C17\,^{\circ}\text{C}. Calculate the temperature of its hot reservoir, in K to 2 significant figures.

Common mistakes

  • Using Celsius in ηCarnot=1−TcTh\eta_\text{Carnot} = 1 - \frac{T_\text{c}}{T_\text{h}}. Convert both temperatures to kelvin first.
  • Taking work done on the gas as positive. In Q=ΔU+WQ = \Delta U + W, WW is the work done by the gas, so a compression has W<0W < 0.
  • Thinking adiabatic means constant temperature. Adiabatic means Q=0Q = 0; the temperature changes because work is done.
  • Saying no net work is done over a cycle because ΔU=0\Delta U = 0. The net work equals the net heat taken in, which is the enclosed area.
  • Saying a well-designed real engine could reach the Carnot efficiency. The Carnot cycle is reversible and infinitely slow, so it is only a limit.

Exam tips

  • "Show, using the first law" that heat enters or leaves: state ΔU\Delta U (from the temperature change), then the sign of WW (expansion or compression), then combine them in Q=ΔU+WQ = \Delta U + W. Each step is a marking point, so don't jump to the conclusion.
  • "Show that" a volume or pressure after an adiabatic change: write P1V153=P2V253P_1V_1^{\frac{5}{3}} = P_2V_2^{\frac{5}{3}} with the numbers in, then give one more significant figure than the stated value.
  • "Sketch" or "draw" a cycle on P-V axes: the marks are for the shapes. Isovolumetric is vertical, isobaric is horizontal, and an adiabatic curve is steeper than an isotherm through the same point.
  • "Explain" why a real engine cannot reach the Carnot efficiency: the Carnot cycle is reversible (no friction, no heat flow across a temperature difference) and would have to run infinitely slowly.

Key takeaways

Learn thisIn Q=ΔU+WQ = \Delta U + W, QQ is the heat supplied to the gas and WW is the work done by the gas. Work done on the gas (compression) is negative.
Learn thisFor an ideal gas. Isovolumetric: W=0W = 0, Q=ΔUQ = \Delta U. Isobaric: W=PΔVW = P\Delta V. Isothermal: ΔU=0\Delta U = 0, Q=WQ = W. Adiabatic: Q=0Q = 0, W=−ΔUW = -\Delta U.
In bookletPV53=constantPV^{\frac{5}{3}} = \text{constant}
Learn thisWork done by a gas is the area under its P-V line, negative when the gas is compressed. Over a cycle, the net work is the enclosed area, done by the gas when the loop runs clockwise.
In bookletη=useful workinput energy\eta = \frac{\text{useful work}}{\text{input energy}}
Learn thisFor a heat engine, W=Qh−QcW = Q_\text{h} - Q_\text{c}, and the input energy is QhQ_\text{h}, the heat taken in.
In bookletηCarnot=1−TcTh\eta_\text{Carnot} = 1 - \frac{T_\text{c}}{T_\text{h}}
Learn thisThe Carnot efficiency, with temperatures in kelvin, is the maximum for any heat engine between two reservoirs. Real engines are irreversible and always less efficient.

Practise this

42 past-paper questions on Thermodynamics, entropy and cycles in the Physics HL bank, each with a mark scheme and a worked explanation.

Practise Thermodynamics, entropy and cycles →