2.13 · SLPaper 1Paper 2

Resistance, resistivity and Ohm's law

In a minute

A carries an because it has mobile ; an has almost none. Collisions between carriers and vibrating ions cause , R=VIR = \frac{V}{I}, and heat the material. describes the material whatever its shape, and says when current is proportional to .

You'll be able to

  • Explain why metals conduct and plastics do not, in terms of mobile charge carriers.
  • Explain where resistance comes from, and why a hot metal resists more.
  • Use R=VIR = \frac{V}{I} to find a resistance, a current or a potential difference, with the right units and prefixes.
  • Use ρ=RAL\rho = \frac{RA}{L} to find a wire's resistance or resistivity, and predict how RR changes with its shape.
  • State Ohm's law, and use I–V graphs to tell ohmic from such as a filament lamp.
Before you start3 quick questions on what this builds on
Check yourself
A charge of 42 C\pu{42 C} flows past a point in a wire in 2.5 min\pu{2.5 min}. Calculate the current, to 2 significant figures.
Check yourself
Moving 2.2 C\pu{2.2 C} of charge through a component transfers 33 J\pu{33 J} of energy. Calculate the potential difference across it, in volts.
Check yourself
Which of these is an SI base unit?

Revise first: 2.12 Current, potential difference and emf and 6.1 Units, measurement and estimation

Conductors and insulators

A cell drives a current through a copper wire but not through a plastic ruler. Both are full of , so the difference is whether that charge can move.

In 2.12 you met charge carriers: charged particles that move to carry a current. A material conducts well only if it has many charge carriers that are free to move through it.

In a metal, each atom gives up one or more outer electrons. These free electrons wander through the whole metal, while the positive ions stay in a fixed lattice. So the charge carriers in a metal are electrons.

In a salt solution the carriers are positive and negative ions. Semiconductors such as silicon sit in between: far fewer free carriers than a metal, with more freed as they warm up.

Worked exampleA cable has a copper core inside a PVC plastic coating. Explain, in terms of charge carriers, why a potential difference across the cable produces a current in the copper but not in the PVC.

Try it first, then reveal one step at a time.

  1. Marking point 1: copper has many free electrons.
Worked exampleSolid sodium chloride does not conduct electricity, but a solution of sodium chloride in water does. Explain why.

Try it first, then reveal one step at a time.

  1. Marking point 1: sodium chloride is made of ions.
Check yourself
What are the charge carriers in a copper wire?
Check yourself
Why is glass an insulator?

Where resistance comes from

A potential difference across a metal wire sets up an electric field inside it. The field pushes on every free electron, so each one gains velocity in the same direction, on top of its random motion.

An electron does not speed up for long. It soon hits one of the lattice ions, which vibrate about fixed positions, and bounces off in a new direction. Then the field speeds it up again.

A section of metal wire drawn as a rectangle filled with a regular grid of positive lattice ions. The left end is marked minus and the right end is marked plus. A free electron follows a zig-zag path from left to right, changing direction each time it hits an ion. Below the wire, an arrow pointing right is labelled electron drift, and an arrow pointing left is labelled conventional current. − + ++++++ ++++++ ++++++ free electron electron drift conventional current lattice ions vibrate about fixed positions
Electrons drift slowly towards the positive end, opposite to the conventional current.

The result is a slow drift of electrons along the wire. These collisions are the origin of : they oppose the flow of charge, so a bigger potential difference is needed for the same current.

Each collision gives some of the electron's kinetic energy to the lattice. The ions vibrate more, so the wire's internal energy and temperature rise: the heating effect of a current. A charge qq passing through transfers energy W=qVW = qV.

Heat a metal and its ions vibrate with a larger amplitude. Electrons collide with them more often, so a metal's resistance rises with temperature.

Worked exampleExplain, using a particle model, why the resistance of a metal wire increases when its temperature increases.

Try it first, then reveal one step at a time.

  1. Marking point 1: free electrons move through a lattice of ions.
Worked exampleThere is a potential difference of 4.5 V\pu{4.5 V} across a resistor. In 2.0 min\pu{2.0 min}, a charge of 18 C\pu{18 C} flows through it. Calculate the energy transferred to the internal energy of the resistor.

Try it first, then reveal one step at a time.

  1. Potential difference is energy per unit charge, so W=qVW = qV.
Check yourself
What is the effect of free electrons colliding with the lattice ions in a resistor?
Check yourself
A heating element has a potential difference of 12 V\pu{12 V} across it and transfers 360 J\pu{360 J} to internal energy. Calculate the charge that flowed through it, in coulombs.

Resistance, R = V/I

Two lamps on the same potential difference can carry very different currents. Resistance puts a number on this: how many volts you need for each ampere.

In the formula booklet
R=VIR = \frac{V}{I}

The of resistance is the ohm, Ω\Omega: 1 Ω=1 V A−1\pu{1 \Omega} = \pu{1 V A-1}. Kilohms (103 Ω10^{3}\ \Omega) and megohms (106 Ω10^{6}\ \Omega) are common.

R=VIR = \frac{V}{I} is in the data booklet. It defines resistance, so it holds for any component at any moment, even when RR changes with the current.

To measure RR, put an ammeter in series with the component and a voltmeter in parallel across it. Treat meters as ideal unless told otherwise: zero resistance for an ammeter, infinite for a voltmeter.

Circuit diagram. A cell, an ammeter and a resistor are connected in series in a single loop. A voltmeter is connected in parallel across the resistor only, on a separate branch above it. A V resistor ammeter in series voltmeter in parallel cell
The ammeter measures the current in the resistor; the voltmeter measures the potential difference across it.
Worked exampleA voltmeter across a small heating element reads 5.4 V\pu{5.4 V} while an ammeter in series with it reads 1.2 A\pu{1.2 A}. Calculate the resistance of the element.

Try it first, then reveal one step at a time.

  1. Write the definition: R=VIR = \frac{V}{I}.
Worked exampleA resistor of resistance 3.3 kΩ\pu{3.3 k\Omega} has a potential difference of 1.5 V\pu{1.5 V} across it. Calculate the current in the resistor.

Try it first, then reveal one step at a time.

  1. Convert the prefix: R=3.3×103 ΩR = 3.3 \times 10^{3}\ \Omega.
Check yourself
The current in a lamp is 0.40 A\pu{0.40 A} when the potential difference across it is 9.6 V\pu{9.6 V}. Calculate its resistance in ohms, to 2 significant figures.
Check yourself
Which of these is equivalent to one ohm?

Resistivity

A long thin wire resists more than a short thick one of the same metal. Double the length and each electron passes twice as many ions, so the resistance doubles: R∝LR \propto L.

Double the cross-sectional area and it is like two wires side by side. Twice the current flows for the same potential difference, so R∝1AR \propto \frac{1}{A}.

Together, R=ρLAR = \frac{\rho L}{A}. The constant ρ\rho is the . It depends on the material and its temperature, not on the wire's length or thickness.

In the formula booklet
ρ=RAL\rho = \frac{RA}{L}

Its unit is the ohm metre, Ω m\Omega\ \text{m}. Values range from about 10−8 Ω m10^{-8}\ \Omega\ \text{m} for copper and 10−6 Ω m10^{-6}\ \Omega\ \text{m} for nichrome to over 1012 Ω m10^{12}\ \Omega\ \text{m} for plastics.

For a round wire, A=πr2=πd24A = \pi r^{2} = \frac{\pi d^{2}}{4}, in metres. In the lab, measure dd with a micrometer at several places and take the mean.

Worked exampleA heater coil is made from 1.8 m\pu{1.8 m} of nichrome wire of diameter 0.40 mm\pu{0.40 mm}. The resistivity of nichrome is 1.1×10−6 Ω m1.1 \times 10^{-6}\ \Omega\ \text{m}. Calculate the resistance of the coil.

Try it first, then reveal one step at a time.

  1. Radius in metres: r=2.0×10−4 mr = 2.0 \times 10^{-4}\ \text{m}.
Worked exampleA metal wire of resistance RR is drawn out to three times its length, keeping a uniform cross-section. Its volume and resistivity do not change. Determine the new resistance as a multiple of RR.

Try it first, then reveal one step at a time.

  1. The volume ALAL is constant, so tripling LL divides the area by 3.
Check yourself
A graph of the resistance RR of a wire against its length LL is a straight line through the origin with gradient 8.0 Ω m−18.0\ \Omega\ \text{m}^{-1}. The wire's cross-sectional area is 2.0×10−7 m22.0 \times 10^{-7}\ \text{m}^{2}. Calculate the resistivity in Ω m\Omega\ \text{m}.
Check yourself
Wire Y is made of the same metal as wire X. It is twice as long and has twice the diameter. What is RYRX\frac{R_Y}{R_X}?

Ohm's law and non-ohmic conductors

Measure II for several values of VV across a metal wire kept at a steady temperature. The graph is a straight line through the origin: double VV and II doubles.

A component that obeys Ohm's law is ohmic: its resistance is constant and its I–V graph is a straight line through the origin. A metal conductor at constant temperature counts as ohmic.

A does not obey Ohm's law. Its resistance changes with the current, so its I–V graph is not a straight line through the origin.

Three graphs of current I against potential difference V, each with the origin in the middle so that negative values are shown. First, an ohmic resistor at constant temperature: a straight line through the origin. Second, a filament lamp: a curve through the origin that is steep near the origin and becomes less steep at larger positive and negative potential differences, symmetric about the origin. Third, a light-emitting diode: the current is zero for all negative potential differences and for small positive ones, then rises steeply once the positive potential difference passes a threshold. VI VI VI ohmic resistor constant temperature filament lamp resistance rises as it heats LED conducts one way only
I–V characteristics. Only the ohmic resistor gives a straight line through the origin.

A filament lamp is non-ohmic because of the heating effect. A bigger current makes the filament hotter, so its resistance rises. The current grows more slowly than VV, and the graph bends towards the VV-axis.

Every resistor heats up when it carries a current. A metal's resistance changes with temperature, so a metal resistor obeys Ohm's law only while its temperature is steady. You will calculate the heating power in 2.14.

An LED conducts in one direction only, and only above a threshold potential difference. An NTC thermistor's resistance falls as it warms, because more carriers are freed. Both are non-ohmic.

For any component, the resistance at a point on the I–V graph is VI\frac{V}{I} at that point, not the reciprocal of the gradient.

Worked exampleA filament lamp carries a current of 0.15 A\pu{0.15 A} when the potential difference across it is 2.4 V\pu{2.4 V}, and 0.24 A\pu{0.24 A} when it is 7.2 V\pu{7.2 V}. Determine the increase in the lamp's resistance between these two readings.

Try it first, then reveal one step at a time.

  1. First reading: R1=VI=2.40.15=16 ΩR_1 = \frac{V}{I} = \frac{2.4}{0.15} = 16\ \Omega.
Worked exampleExplain why the I–V graph of a filament lamp is a curve rather than a straight line through the origin.

Try it first, then reveal one step at a time.

  1. Marking point 1: a larger current raises the filament's temperature.
Check yourself
Which statement is Ohm's law?
Check yourself
The potential difference across a filament lamp rises from zero to its working value. What happens to its resistance?

Common mistakes

  • Calling R=VIR = \frac{V}{I} Ohm's law. R=VIR = \frac{V}{I} defines resistance for any component; Ohm's law says I∝VI \propto V at constant temperature.
  • Finding the resistance of a curved I–V graph from its gradient. Read VV and II at the point and divide.
  • Writing the unit of resistivity as Ω m−1\Omega\ \text{m}^{-1}. From ρ=RAL\rho = \frac{RA}{L} it is Ω m\Omega\ \text{m}.
  • Saying the current is used up in a resistor. The same current enters and leaves; the resistor takes energy from the charge carriers.

Exam tips

  • "State" Ohm's law: say the current is directly proportional to the potential difference, and add "at constant temperature".
  • "Outline" how a lamp's resistance changes as the current rises: "it increases". Don't say it then becomes constant, and don't argue from the gradient.
  • "Calculate" with resistivity: write ρ=RAL\rho = \frac{RA}{L}, show A=πr2A = \pi r^{2} with rr in metres, then give the answer with its unit to 2 or 3 significant figures.
  • Paper 1A wire-ratio questions: write R=ρLAR = \frac{\rho L}{A}, change one quantity at a time, and remember the area goes as the diameter squared.

Key takeaways

In bookletR=VIR = \frac{V}{I}
In bookletρ=RAL\rho = \frac{RA}{L}
Learn thisConductors have many mobile charge carriers (free electrons in metals, ions in solutions); insulators have very few.
Learn thisResistance comes from carriers colliding with vibrating lattice ions. The collisions heat a resistor, and a hotter metal has a larger resistance.
Learn thisResistivity, in Ω m\Omega\ \text{m}, belongs to the material; for a round wire use A=πr2A = \pi r^{2} with rr in metres.
Learn thisOhm's law: for a metal conductor, I∝VI \propto V at constant temperature. Ohmic means a straight I–V line through the origin.
Learn thisA filament lamp is non-ohmic: its resistance rises as it heats. At any point, R=VIR = \frac{V}{I}, not the gradient.

Practise this

94 past-paper questions on Current, resistance, circuits and heating in the Physics HL bank, each with a mark scheme and a worked explanation.

Practise Current, resistance, circuits and heating →