Units, measurement and estimation
In a minute
Every measured value needs a unit, a sensible precision and a size you can judge. This lesson covers safe, careful measurement, , prefixes and , handy units such as the , checking equations with units, and estimating to the nearest .
You'll be able to
- Address the safety, ethical and environmental issues in an investigation.
- Choose and read the right instrument for each common quantity, to an appropriate precision.
- Use SI units, prefixes and scientific notation.
- Express derived units in fundamental units, and use units to check an equation.
- Use eV, , ly, pc, h, days and years where they fit, and convert them to SI.
- Quote values, ratios and estimates to the nearest order of magnitude.
Before you start3 quick questions on what this builds on
Safety, ethics and the environment
A risk assessment lists each hazard and the control measure that lowers its risk. Common physics hazards:
1. Electricity: use low-voltage supplies, check leads for damage and keep water away from mains equipment.
2. Heaters and hot water: let them cool before handling.
3. Lasers: never look along the beam, and remove shiny surfaces that could reflect it.
4. Radioactive sources: use tongs and return them to their lead-lined box promptly. Less time, more distance and shielding all cut your dose.
5. Stretched wires and hanging masses: wear eye protection and put something soft below.
Ethical issues are about honesty and people. Record every result, including ones that don't fit, and credit others' data. If people take part, get their informed consent.
Environmental issues are about waste: switch equipment off, use only the materials you need, and recycle batteries.
Try it first, then reveal one step at a time.
- Name the hazards: the snapping wire, and the masses that then drop.
- Give one control for each, with its reason.
- Wear safety goggles, because the wire whips back when it snaps and could hit the eyes. Place a box of foam under the masses, because they fall when the wire breaks and could injure someone's feet.
Try it first, then reveal one step at a time.
- Ethics applies because people take part.
- The classmates are human participants, so the student must get their informed consent first. Each person must be free to withdraw at any time. Results should be recorded by number, not name, so they stay anonymous.
Measuring to the right precision
An instrument's resolution is the smallest change it can show: for a metre rule. Pick an instrument whose resolution is small compared with the quantity, and read it to that resolution.
Length: metre rule (), vernier calipers ( or better), micrometer (). Check for a zero error, which shifts every reading equally.
Mass: an electronic balance, zeroed (tared) with any container on it.
Time: a stopwatch shows , but reaction time is about . Time many cycles and divide, or use light gates for short intervals.
Volume: a measuring cylinder, read at eye level.
Temperature: a thermometer or temperature probe; stir and wait for the reading to settle. Force: a newton meter or force sensor, zeroed first. Angle: a protractor, to .
Current and potential difference: an ammeter in series with the component, a voltmeter in parallel across it. On a digital meter, use the range that shows the most digits.
Sound and light intensity: a sound level meter or a light meter (or sensors). Keep the distance and direction fixed, and record the background reading. A light meter's background can be subtracted directly; a sound level meter reads in decibels, a logarithmic scale, so convert both readings to intensities before subtracting.
Repeat readings and take the mean to reduce random scatter. Uncertainties are in 6.3.
Try it first, then reveal one step at a time.
- Divide the total time by the number of oscillations: .
- Reaction time adds about 0.2 s of error to the total, however long it is.
- Shared over 25 oscillations, that is under 0.01 s each, tiny compared with the period.
Try it first, then reveal one step at a time.
- Pick the instrument: a ruler's divisions are bigger than the wire.
- Then deal with zero error and with an uneven wire.
- Use a micrometer screw gauge, which reads to 0.01 mm, because a ruler's resolution is larger than the wire. Close the jaws with nothing between them and note any zero error, then correct every reading for it. Measure the diameter at several points along the wire, turning it each time, and take the mean.
SI units, prefixes and scientific notation
IB Physics uses the first six; the candela does not appear.
Very large and very small values are written in . The speed of light, , becomes .
The power counts how far the decimal point moves. Negative means a number below 1: .
An does the same job. Replace it with its power of ten: .
Case matters: is milli but is mega.
When a prefixed unit is squared or cubed, the power of ten is too: and .
Try it first, then reveal one step at a time.
- Replace the prefix: , so .
- Bring the number into the range 1 to 10: .
- Add the indices: .
Try it first, then reveal one step at a time.
- Convert the area to first: .
- Substitute: .
- Dividing by multiplies by : .
- Both data have 2 significant figures, so the answer has 2.
Fundamental and derived units
A derived unit is built from fundamental units by the equation that defines the quantity. The newton comes from : .
To convert any unit: write a defining equation, replace each quantity by its fundamental units, then collect the powers.
The joule follows from work force distance: . The coulomb follows from : .
Units also catch mistakes. You can only add, subtract or equate quantities with the same units, so every term of a correct equation has the same units.
Try it first, then reveal one step at a time.
- Resistance is , so .
- Potential difference is energy per charge, , so .
- Substitute : .
- Divide by one more ampere for the ohm.
- Since and , the ohm is .
Try it first, then reveal one step at a time.
- Fundamental units of : .
- Then has units , and its square root has units .
- Turning the fraction over gives , which matches. The check cannot confirm the .
- The units of are , so has units of , not seconds. The two sides do not match, so the equation is wrong. The form has units of seconds, so it passes the check.
Units that suit the problem
A particle's energy in joules is tiny, and a star's distance in metres is huge. Units that fit the scale are easier; convert to SI before calculating.
The comes from with , the elementary charge. With prefixes you get keV, MeV and GeV.
Since , a mass can be given as an energy divided by . The unit is or : an electron's rest mass is .
For astronomical distances, the light-year (ly) is the distance light travels in one year, . A light-year is a distance, not a time.
The (pc) is . Both conversions, the value of and the electron's mass are in the data booklet.
Hours (h), days and years suit half-lives and ages. In seconds: , 1 day , 1 year .
Try it first, then reveal one step at a time.
- Replace the prefix: .
- Multiply by the joules in one electronvolt: .
- and , so .
- Round to 2 significant figures, as in the data.
Try it first, then reveal one step at a time.
- Parsecs to light-years: .
- Light-years to metres: . Use the unrounded value.
- , so the distance is .
- Give 2 significant figures, as in the data.
Orders of magnitude
Often you only need to know roughly how big something is: nearer a thousand or a million?
So has an of , but is nearer . Don't just copy the power from scientific notation.
To compare two values, divide them and find the order of magnitude of the ratio. A ratio of about means one is three orders of magnitude bigger than the other.
An estimate uses rounded values you can judge, with your assumptions stated. Give the result to one significant figure or as a power of ten.
Try it first, then reveal one step at a time.
- Divide: .
- is below , so the nearest power of ten is .
- The Earth's radius is 17 orders of magnitude bigger than the atom's.
Try it first, then reveal one step at a time.
- Assume a room about 8 m long, 6 m wide and 3 m high.
- Volume: .
- Mass density volume: .
- is below , so the order of magnitude is .
Common mistakes
- Mixing up prefix case: is a milliwatt, a megawatt.
- Taking the power in scientific notation as the order of magnitude. is nearer than .
- Treating the light-year as a time. It is the distance light travels in a year.
- Trusting an equation because its units match. Units can't show a missing or .
- Reading a meniscus from above, or forgetting a zero error. Read at eye level, and check the zero before you start.
Exam tips
- Paper 1A unit questions: build the unit step by step from equations you know (, , , , ).
- "Estimate": write down your rounded values and assumptions, then give one significant figure or a power of ten.
- "Suggest" a precaution: give the control measure and the hazard it deals with, joined by "because".
- Give every final answer with a unit, in scientific notation when it is very large or small, and to the significant figures of the least precise datum (decimal places for sums and differences).
Key takeaways
Practise this
10 past-paper questions on Measurements, units and dimensions in the Physics HL bank, each with a mark scheme and a worked explanation.