IGCSE Physics 0625 · Paper practice

Paper 4 past paper questions

Every archived Physics 0625 Paper 4 question in one place. Practise them by topic, then sit a full paper under timed conditions.

Most-tested topicsMotion, forces and energy 179Earlier syllabus topics 148Electricity and magnetism 148Thermal physics 99Waves 96Nuclear physics 56

Course route
Sort questions

You’re practising 2019–2021 papers. The 2022–2026 papers, including 2026, need a plan.

Unlock from $6/mo
24 free questions

2021 MarchPaper 4Question 1Component 42Variant 210 marks
Motion, forces and energyPressure
Loading original question

1 (a) Fig. 1.1 shows a piece of glass of thickness 2.0 cm and area 0.15 m2. The density of the glass is 2.6 × 103 kg / m3. area 0.15 m2 thickness 2.0 cm Fig. 1.1 (not to scale) Calculate the weight of the piece of glass. weight = … [3] (b) The piece of glass shown in Fig. 1.1 is used as the vertical viewing window of an aquarium. The atmospheric pressure outside the aquarium is 1.0 × 105 Pa. The average pressure on the inside of the aquarium window is 1.3 × 105 Pa. Calculate the resultant force acting on the window due to these pressures and state the direction in which it acts. force = … direction of force … [4] (c) Fig. 1.2 shows a vacuum pump connected to the top of a vertical tube with its lower end immersed in a tank of liquid. The pump reduces the pressure above the column to zero and the pressure at point X is 9.6 × 104 Pa. point X 12 m liquid vacuum pump Fig. 1.2 (not to scale) Calculate the density of the liquid. density = … [3] [Total: 10]

2021 JunePaper 4Question 1Component 41Variant 110 marks
Earlier syllabus topicsEarlier syllabus content
Loading original question

1 A skydiver of mass 76 kg is falling vertically in still air. At time t = 0, the skydiver opens his parachute. Fig. 1.1 is the speed–time graph for the skydiver from t = 0. 0 0 1 2 3 4 5 6 20 40 60 t / s speed m / s Fig. 1.1 (a) Using Fig. 1.1, determine: (i) the deceleration of the skydiver immediately after the parachute opens deceleration = … [2] (ii) the force due to air resistance acting on the skydiver immediately after the parachute opens. force = … [3] (b) Explain, in terms of the forces acting on the skydiver, his motion between t = 0 and t = 6.0 s.… [3] (c) Explain why opening the parachute cannot reduce the speed of the skydiver to zero.… [2] [Total: 10]

2021 JunePaper 4Question 1Component 42Variant 29 marks
Earlier syllabus topicsEarlier syllabus content
Loading original question

1 (a) Fig. 1.1 shows a sealed weather balloon which is stationary in still air. weather balloon instruments Fig. 1.1 State whether the overall density of the balloon and its instruments is greater than, less than, or the same as the density of the surrounding air. … [1] (b) At night, the gas inside the balloon cools. The pressure of the air outside the balloon remains the same. (i) State whether the balloon rises, falls or remains stationary. … [1] (ii) Explain your answer.… [2] (c) An object is released from the balloon. It starts at rest and eventually reaches a constant speed. (i) On the axes of Fig. 1.2, sketch a speed–time graph to show this motion. speed time 0 0 Fig. 1.2 [3] (ii) State the values of the initial acceleration and the final acceleration of the object. initial acceleration … final acceleration … [2] [Total: 9]

2021 JunePaper 4Question 1Component 43Variant 39 marks
Motion, forces and energyForcesEffects of forces
Loading original question

1 Fig. 1.1 shows a load suspended from a spring. load spring Fig. 1.1 The value of the spring constant k of the spring is 0.20 N / cm. The spring reaches its limit of proportionality when the load is 15 N. (a) Calculate the extension of the spring when the load is 3.0 N. extension = … [2] (b) Explain what is meant by the term limit of proportionality of the spring.… [2] (c) On Fig. 1.2, sketch an extension–load graph for a spring. Label the limit of proportionality with the letter L on your graph. extension 0 0 load Fig. 1.2 [2] (d) The load is pulled down a small distance below its equilibrium position to position A, as shown in Fig. 1.3. The load then moves up and down between position A and position B in Fig. 1.3. position A position B Fig. 1.3 Describe the energy transfers which occur as the load moves: from position A to the equilibrium position… from the equilibrium position to position B.… [3] [Total: 9]

2021 NovemberPaper 4Question 1Component 41Variant 19 marks
Earlier syllabus topicsEarlier syllabus content
Loading original question

1 Some physical quantities are scalars and other physical quantities are vectors. (a) State how a vector quantity differs from a scalar quantity.… [1] (b) Circle the vector quantities in the list. acceleration energy mass momentum temperature time speed velocity [2] (c) A microphone in a recording studio has a mass of 0.55 kg and a weight W. (i) Calculate W. W = … [1] (ii) The microphone is suspended from the ceiling by a cord attached to a small ring. Fig. 1.1 shows the microphone pulled to one side and kept stationary by a horizontal thread. ceiling cord microphone ring horizontal thread Fig. 1.1 (not to scale) The tension T in the horizontal thread is 8.1 N. Determine graphically the magnitude and the direction, relative to the vertical, of the resultant of W and T. Use a scale of 1.0 cm to 1.0 N or greater. magnitude of resultant = … direction of resultant = … relative to vertical [3] (iii) State and explain how the magnitude and direction of the resultant in (c)(ii) compares with the force on the ring due to the tension in the cord.… [2] [Total: 9]

2021 NovemberPaper 4Question 1Component 42Variant 25 marks
Earlier syllabus topicsEarlier syllabus content
Loading original question

1 Fig. 1.1 shows a space rocket accelerating away from a launch pad. Fig. 1.1 Fig. 1.2 is a speed–time graph for the first 30 s of the rocket’s flight. 0 0 500 1000 speed m / s 1500 2000 10 time / s 20 30 Fig. 1.2 (a) Describe how the acceleration of the rocket changes between time = 10 s and time = 30 s. … [1] (b) By drawing a tangent to the graph, determine the acceleration of the rocket at time = 25 s. acceleration = … [2] (c) Determine the distance travelled by the rocket between time = 0 and time = 10 s. distance = … [2] [Total: 5]

2021 NovemberPaper 4Question 1Component 43Variant 38 marks
Earlier syllabus topicsEarlier syllabus content
Loading original question

1 A ship sails in a straight line between two ports. Fig. 1.1 shows the speed–time graph of the ship for the first 100 minutes of its journey between the two ports. 0 0 20 40 time / min 60 80 100 5 10 15 speed m / s 20 Fig. 1.1 (a) Calculate the maximum acceleration during the first 100 minutes of the ship’s journey. maximum acceleration = … [2] (b) Calculate the total distance travelled by the ship between time = 42 min and time = 100 min. distance travelled = … [3] (c) At a time not shown on the graph, the acceleration of the ship is 0.0087 m / s2. The total mass of the ship and its passengers is 2.3 × 107 kg. (i) Calculate the resultant force on the ship. force = … [2] (ii) Explain why the force on the ship due to the ship’s engine is greater than the value you calculated in (c)(i).… [1] [Total: 8]

2021 MarchPaper 4Question 2Component 42Variant 211 marks
Earlier syllabus topicsEarlier syllabus content
Loading original question

2 (a) (i) State what is meant by the moment of a force about a point. … [1] (ii) Fig. 2.1 shows a large crane on a construction site lifting a block of mass 14 000 kg. 20 m B A block counterweight operator’s cabin Fig. 2.1 Calculate the moment about A due to the 14 000 kg block suspended from B. moment = … [2] (b) (i) Speed is a scalar quantity and velocity is a vector quantity. State the difference between a scalar quantity and a vector quantity.… [2] (ii) Write down one other scalar quantity and one other vector quantity. scalar quantity … vector quantity … [2] (c) Fig. 2.2 shows two forces acting on an object. 60° 30 N 20 N Fig. 2.2 (not to scale) Draw a scale diagram to determine the resultant force acting on the object. State the scale you use. scale … magnitude of resultant force = … direction of resultant relative to the direction of the 20 N force = … [4] [Total: 11]

2021 JunePaper 4Question 2Component 41Variant 17 marks
Earlier syllabus topicsEarlier syllabus content
Loading original question

2 Fig. 2.1 shows a wooden trolley of mass 1.2 kg at rest on the rough surface of a bench. trolley ball Fig. 2.1 A ball of mass 0.52 g travels horizontally towards the trolley. The ball embeds itself in the wood of the trolley. The trolley moves with an initial speed of 0.065 m / s. (a) Calculate: (i) the impulse exerted on the trolley impulse = … [2] (ii) the speed of the ball as it hits the trolley. speed = … [2] (b) As the trolley moves across the rough surface, it slows down and stops. Explain, in terms of the work done, the energy change that takes place as the trolley slows down.… [3] [Total: 7]

2021 JunePaper 4Question 2Component 42Variant 26 marks
Earlier syllabus topicsEarlier syllabus content
Loading original question

2 (a) Define the moment of a force. … [1] (b) Fig. 2.1 shows an object of negligible weight. The object is in equilibrium. 12 cm 20 cm pulley 50 kg mass object pivot P rope force F Fig. 2.1 The object is free to rotate about its pivot P. Calculate the value of force F. F = … [2] (c) Describe an experiment involving vertical forces to show that there is no net moment on an object in equilibrium. You may draw a diagram in the space provided.… [3] [Total: 6]

2021 JunePaper 4Question 2Component 43Variant 39 marks
Motion, forces and energyPressure
Loading original question

2 (a) Fig. 2.1 shows a bookshelf with two groups of books A and B on it. There are six books in each group of books. All the books are identical. The mass of each book is 0.52 kg. 30 cm 21 cm 21 cm 1.3 cm 1.3 cm 30 cm shelf group A of books group B of books Fig. 2.1 (i) Explain why the pressure exerted on the shelf by the books in group B is less than the pressure exerted on the shelf by the books in group A.… [3] (ii) Calculate the pressure exerted on the shelf by the books in group A. pressure = … [3] (b) A diver dives to a depth below the surface of the sea where the total pressure is 3.0 × 105 Pa. The atmospheric pressure is 1.0 × 105 Pa. The density of the sea water is 1030 kg / m3. Calculate the depth of the diver below the surface of the sea. depth = … [3] [Total: 9]

2021 NovemberPaper 4Question 2Component 41Variant 111 marks
Earlier syllabus topicsEarlier syllabus content
Loading original question

2 A student carries out an experiment using a plastic beaker that contains 0.24 kg of water at 17 °C. The thermal capacity (heat capacity) of the beaker is negligible. (a) Define thermal capacity.… [2] (b) Several ice cubes are at a temperature of 0 °C. The ice cubes are dropped into the water and the internal energy of the water decreases. (i) Give a simple molecular account of this decrease in internal energy.… [2] (ii) The specific heat capacity of water is 4200 J / (kg °C). Calculate the decrease in the internal energy of the water as its temperature decreases from 17 °C to 0 °C. decrease in internal energy = … [2] (c) As the temperature of the water decreases, some of the ice melts. (i) Explain why this ice melts.… [2] (ii) Describe how to determine the specific latent heat of fusion of ice using this experiment. State any other measurements that the student needs to make.… [3] [Total: 11]

2021 NovemberPaper 4Question 2Component 42Variant 28 marks
Motion, forces and energyForcesEffects of forces
Loading original question

2 (a) State Hooke’s law.… [1] (b) Fig. 2.1 shows the extension–load graph for a spring. 0 0 100 extension / mm 200 10 load / N 20 30 Fig. 2.1 (i) On Fig. 2.1, mark and label the region where the spring obeys Hooke’s law. [1] (ii) Calculate the spring constant k. k = … [2] (iii) The original length of the spring is 120 mm. Calculate the length of the spring when a load of 8.5 N is applied to the spring. length = … [2] (c) The weight of an object is 4.0 N on a planet where the acceleration of free fall is 8.7 m / s2. Calculate the mass of the object. mass = … [2] [Total: 8]

2021 NovemberPaper 4Question 2Component 43Variant 37 marks
Motion, forces and energyEnergy, work and powerPower
Loading original question

2 Fig. 2.1 shows a simplified version of a ‘gravity lamp’. This apparatus is used to light a light-emitting diode (LED) without mains electricity. LED attachment to ceiling generator strap 12 kg load Fig. 2.1 The load of 12 kg is raised to a height of 1.7 m above the ground. The load is connected to a pulley system. The time taken for the load to fall to the ground is 1200 seconds. The load falls at constant speed. The generator is connected to an LED. (a) Calculate the rate of transfer of gravitational potential energy as the load falls to the ground. rate of transfer of gravitational potential energy = … [4] (b) The light output of the LED is 0.10 W. Calculate the efficiency of the ‘gravity lamp’. efficiency = … [2] (c) Suggest a social or environmental advantage of using a ‘gravity lamp’.… [1] [Total: 7]

2021 MarchPaper 4Question 3Component 42Variant 26 marks
Earlier syllabus topicsEarlier syllabus content
Loading original question

3 A power station burns waste materials from farm crops to generate electricity. (a) State and explain whether this process is renewable. statement … explanation… [2] (b) The power station uses some of its waste thermal energy to heat water for houses in a nearby town. State one problem of using waste energy in this way if the power station is far from the town. … Suggest a way of reducing this problem.… [2] (c) State two environmental consequences of burning coal to generate electricity. consequence 1. … consequence 2. … [2] [Total: 6]

2021 JunePaper 4Question 3Component 41Variant 18 marks
Motion, forces and energyPressure
Loading original question

3 (a) Explain, in terms of molecules, why liquids are very difficult to compress.… [2] (b) Fig. 3.1 shows a device that uses liquid pressure to lift heavy boxes. boxes pump moving oil piston cylinder oil Fig. 3.1 The boxes are lifted by pumping oil into the cylinder. The force upwards on the piston due to the oil, and the force downwards on the piston due to the air above the piston, combine to produce a constant force of 8800 N. The pressure of the air is 1.0 × 105 Pa and the cross-sectional area of the bottom surface of the piston is 0.016 m2. (i) Calculate the pressure of the oil at the bottom surface of the piston. pressure = … [3] (ii) As the boxes are lifted, the depth of the oil increases. Explain why the pump must exert an increasing pressure on the oil as the depth of the oil increases.… [2] (iii) Suggest one reason why the force of 8800 N in (b) cannot lift boxes of weight 8800 N.… [1] [Total: 8]

2021 JunePaper 4Question 3Component 42Variant 27 marks
Earlier syllabus topicsEarlier syllabus content
Loading original question

3 Fig. 3.1 shows water flowing at very slow speed over a cliff edge. water rocks 15 m cliff edge Fig. 3.1 The water falls 15 m onto the rocks below. (a) Show that the velocity of the water when it strikes the rocks is 17 m / s. [4] (b) 30 kg of water flows over the cliff edge every second. Calculate the force exerted by the rocks on the falling water. Ignore any splashing. force = … [3] [Total: 7]

2021 JunePaper 4Question 3Component 43Variant 38 marks
Earlier syllabus topicsEarlier syllabus content
Loading original question

3 A car travels at constant speed v on a horizontal, straight road. The driver sees an obstacle on the road ahead. (a) The distance travelled in the time between the driver seeing the obstruction and applying the brakes is the thinking distance. Explain why the thinking distance is directly proportional to v.… [1] (b) When the brakes are applied, the car decelerates uniformly to rest. The frictional force applied by the brakes is constant. The distance travelled between first applying the brakes and the car stopping is the braking distance. Explain why the braking distance is proportional to v 2.… [3] (c) The car is travelling at 22 m / s. (i) The thinking distance is 15 m. Calculate the time taken to travel the thinking distance. time = … [2] (ii) The car has a mass of 1400 kg. The time taken for the car to stop after the brakes are applied is 2.1 s. Calculate the force required to stop the car in this time. force = … [2] [Total: 8]

2021 NovemberPaper 4Question 3Component 41Variant 17 marks
Earlier syllabus topicsEarlier syllabus content
Loading original question

3 Fig. 3.1 shows a balloon inflated with air. Fig. 3.1 The pressure of the air at the inner surface of the balloon keeps the rubber stretched. (a) Explain, in terms of the momentum of the molecules, why there is a pressure at the inner surface of the balloon.… [3] (b) The volume of the air in the balloon is 630 cm3 and the pressure of the air in the balloon is 1.0 × 105 Pa. The balloon is tied to a heavy stone and dropped into a lake. The balloon is pulled down quickly and the temperature of the air inside does not change. (i) Calculate the volume of the air when the pressure of the air is 1.4 × 105 Pa. volume = … [2] (ii) The balloon and stone stop moving when the stone hits the bottom of the lake. The temperature of the air now begins to decrease. Explain why the volume of the air in the balloon decreases as the temperature decreases.… [2] [Total: 7]

2021 NovemberPaper 4Question 3Component 42Variant 26 marks
Earlier syllabus topicsEarlier syllabus content
Loading original question

3 Fig. 3.1 shows a collision at very slow speed between two cars travelling along a straight road. car B car A Fig. 3.1 Car B, of mass 800 kg, is moving at 2.0 m / s and collides with car A, of mass 1000 kg, which is stationary. After the collision, both cars travel in the same direction as the initial direction of car B. (a) After the collision, car A moves at 1.3 m / s. Show that the speed of car B after the collision is approximately 0.4 m / s. [3] (b) (i) Calculate the impulse exerted by car A on car B. impulse = … [2] (ii) State the impulse exerted by car B on car A. impulse = … [1] [Total: 6]

Full Paper 4 past papers with mark schemes

Paper 4: quick facts

Which topics come up most in IGCSE Physics 0625 Paper 4?

The most-tagged topics in IGCSE Physics 0625 Paper 4 are Motion, forces and energy (179), Earlier syllabus topics (148) and Electricity and magnetism (148), out of 543 past-paper questions from 2019-2026. These are archive counts, not a prediction, and a question can carry more than one topic.

Are the IGCSE Physics 0625 Paper 4 questions free?

216 of the 543 IGCSE Physics 0625 Paper 4 questions are free to practise. The other 327 need a plan for IGCSE Physics 0625, from $6 a month.

Do the IGCSE Physics 0625 Paper 4 questions have answers?

Yes. Each IGCSE Physics 0625 Paper 4 question shows the official mark scheme answer. Many also have a step-by-step worked explanation written by PastPaperPrep.