IGCSE Physics 0625 · Paper practice

Paper 6 past paper questions

Every archived Physics 0625 Paper 6 question in one place. Practise them by topic, then sit a full paper under timed conditions.

Most-tested topicsExperimental skills and investigations 212Electricity and magnetism 24Waves 22Motion, forces and energy 13Thermal physics 8

Course route
Sort questions

You’re practising 2019–2021 papers. The 2022–2026 papers, including 2026, need a plan.

Unlock from $6/mo
24 free questions

2021 MarchPaper 6Question 1Component 62Variant 211 marks
Experimental skills and investigations
Loading original question

1 A student investigates the motion of an oscillating metre rule. He uses the apparatus shown in Fig. 1.1. clamps vertical threads stands d metre rule horizontal bench Fig. 1.1 (a) The student ensures that the metre rule is horizontal. Briefly describe how to check that the metre rule is horizontal. You may draw a diagram or draw on Fig. 1.1 if it helps to explain your answer.… [1] (b) The student moves the stands so that the vertical threads are at the marks on the metre rule shown in Fig. 1.2. vertical threads 1 2 3 97 96 98 99 Fig. 1.2 Calculate the distance d between the threads. d = … cm [1] (c) He twists the metre rule a small amount, as shown in Fig. 1.3, and then lets it go so that it oscillates in a rotating motion. metre rule seen from above twist one oscillation Fig. 1.3 He measures the time t for 5 complete oscillations of the metre rule. t = … s Suggest why it is useful to take a trial reading for this experiment.… [1] 3.63 (d) The student carries out the same procedure for d values of 20.0 cm, 30.0 cm, 40.0 cm, 50.0 cm and 60.0 cm. His readings are shown in Table 1.1. Table 1.1 d / cm t / s 1 T / 1 s 20.0 17.85 30.0 11.36 0.44 40.0 8.77 0.57 50.0 6.93 0.72 60.0 5.68 0.88 For distance d = 20.0 cm, calculate and record in Table 1.1, the value of 1 T where T is the time for 1 oscillation of the metre rule. Use the value of time t from Table 1.1 and the equation 1 T = 5 t . [1] (e) Plot a graph of distance d / cm (y-axis) against 1 T / 1 s (x-axis). [4] (f) Determine the gradient G of the graph. Show clearly on the graph how you obtained the necessary information. G = … [1] (g) (i) Explain why it is more accurate to measure the time for 5 oscillations rather than for 1 oscillation.… [1] (ii) Describe how the experiment could be improved to make the readings more reliable.… [1] [Total: 11]

2021 JunePaper 6Question 1Component 61Variant 111 marks
Experimental skills and investigations
Loading original question

1 A student investigates the period of a pendulum. Fig. 1.1 and Fig. 1.2 show the arrangement. one complete oscillation clamp clamp floor x bob d l Fig. 1.1 Fig. 1.2 (a) The student measures the distance d between the bottom of the clamp and the floor. 120.0 cm d = … This distance d remains constant throughout the experiment. He adjusts the length l of the pendulum to 70.0 cm. Calculate the distance x between the centre of the pendulum bob and the floor. Record the value of x in the first row of Table 1.1. [1] (b) The student displaces the bob slightly and releases it so that it swings. Fig. 1.2 shows one complete oscillation of the pendulum. He measures, and records in the first row of Table 1.1, the time t for 10 complete oscillations. (i) Calculate, and record in the first row of Table 1.1, the period T of the pendulum. The period is the time for one complete oscillation. [1] (ii) Calculate, and record in the first row of Table 1.1, T 2. [2] (iii) Complete the column headings in Table 1.1. [1] Table 1.1 x / t / T / T 2 / 16.7 45.0 17.3 1.73 2.99 40.0 17.9 1.79 3.20 35.0 18.4 1.84 3.39 30.0 19.0 1.90 3.61 (c) He repeats the procedure using x = 45.0 cm, 40.0 cm, 35.0 cm and 30.0 cm. He records the readings in Table 1.1. Plot a graph of T 2 (y-axis) against x (x-axis). You do not need to start your axes at the origin (0,0). [4] (d) State whether the graph line shows that T 2 is proportional to x. Give a reason for your answer. statement … reason … [1] (e) Explain why timing 10 oscillations gives a more accurate result for the period T than timing one oscillation.… [1] [Total: 11]

2021 JunePaper 6Question 1Component 62Variant 211 marks
Experimental skills and investigations
Loading original question

1 A student determines the density of sand. Fig. 1.1 shows a beaker with a mark at the 250 cm3 level. 250 cm3 Fig. 1.1 (a) Estimate the volume of water VW that the beaker would hold when filled to the top. VW = … cm3 [1] (b) The student uses string and a metre rule to determine the circumference c of the beaker. 21.3 cm c = … Explain briefly how to use the string and the metre rule to determine the circumference c as accurately as possible. You may draw a diagram.… [2] (c) The student measures the height h of the beaker. (i) Show clearly on Fig. 1.1, the height h that he should measure. [1] 9.0 cm His reading is h = … (ii) Calculate the external volume VB of the beaker using the equation VB = hc 2 12.6 . VB = … cm3 [2] (d) The student measures the mass of the beaker on a balance, as shown in Fig. 1.2. (i) Write down the mass mB of the beaker, to the nearest gram. 208.3 g Fig. 1.2 mB = … g [1] The student fills the beaker to the top with dry sand. He measures the mass m of the beaker containing the sand. 724 g m = … (ii) Calculate the mass mS of sand in the beaker. Use the equation mS = (m – mB). mS = … g [1] (iii) Calculate the density ρ of the sand using the equation ρ = mS VB . Include the unit. ρ = … [2] (e) The student uses a measuring cylinder to measure the volume of dry sand. Draw a diagram of the measuring cylinder and show the line of sight that the student must use to obtain an accurate volume reading. [1] [Total: 11]

2021 JunePaper 6Question 1Component 63Variant 311 marks
Experimental skills and investigations
Loading original question

1 A student investigates the behaviour of a spring, and then uses the spring to determine the density of modelling clay. The apparatus is shown in Fig. 1.1. clamp spring load Fig. 1.1 (a) Describe two precautions that the student should take when measuring the length of the spring, to ensure an accurate reading. You may draw a diagram. 1.… 2.… [2] (b) The student measures the length l 0 of the spring without any load. 2.3 l 0 = … cm A load of weight W = 2.0 N is suspended from the spring, as shown in Fig. 1.2. clamp spring 2.0 N load l Fig. 1.2 (i) On Fig. 1.2, measure the stretched length l of the spring. l = … cm [1] (ii) Calculate the extension e of the spring for a load of weight W = 2.0 N. Use the equation e = (l – l 0). e = … cm [1] (c) The 2.0 N load is removed from the spring. A load U is made of modelling clay wrapped on a wire hanger. Load U is suspended from the spring. The student measures the stretched length l U of the spring. 7.4 l U = … cm Calculate the extension eU of the spring with load U. eU = … cm The extension of a spring is directly proportional to the weight of the load. Use your values of W and e from (b)(ii) and your value of eU to determine the weight WU of load U. Show your working. WU = … [2] (d) Load U is fully immersed in a beaker of water, as shown in Fig. 1.3. clamp spring load U bench lW beaker water wire hanger Fig. 1.3 On Fig. 1.3, measure the stretched length l W of the spring. l W = … cm Calculate the extension e W of the spring with load U in the water. e W = … cm Calculate the density ρ of the modelling clay. Use your values of eU from (c), your value of e W and the equation ρ = eU (eU – e W) × k , where k = 1.0 g / cm3. ρ = … g / cm3 [2] (e) Suggest a possible source of inaccuracy in the determination of ρ in this experiment.… [1] (f) The student plots a graph of load against extension for the spring, to show that the two quantities are directly proportional. State how his graph line shows that load and extension are directly proportional.… [2] [Total: 11]

2021 NovemberPaper 6Question 1Component 61Variant 111 marks
Experimental skills and investigations
Loading original question

1 A student investigates the stretching of a spring. Fig. 1.1 shows the apparatus. metre rule clamp stand spring bench 44 45 0 cm mark 100 cm mark Fig. 1.1 (a) The metre rule is clamped in position near to the spring. (i) Write down the scale readings in mm from the metre rule at the top and bottom of the spring, as shown in Fig. 1.1. top reading = … mm bottom reading = … mm [2] (ii) Using the two readings, calculate the length l 0 of the spring in mm. Record l 0 in Table 1.1. The value l 0 is the length of the spring when the load L = 0.00 N. [1] (b) The student suspends a load L = 0.20 N from the spring. He records the new length l of the spring in Table 1.1. (i) Use the equation e = (l – l 0) to calculate the extension e of the spring. Record the value of e in Table 1.1. [1] (ii) Complete the extension column heading in Table 1.1. [1] (c) The student repeats the procedure using loads L = 0.40 N, L = 0.60 N, L = 0.80 N and L = 1.00 N. He records the readings and results in Table 1.1. Table 1.1 L / N l / mm e / 0.00 0 0.20 17 0.40 20 5 0.60 23 8 0.80 25 10 1.00 28 13 Plot a graph of e / mm (y-axis) against L / N (x-axis). [4] (d) Fig. 1.2 shows the unstretched spring and the spring with a load. On Fig. 1.2, show clearly the distances l 0, l and e. Fig. 1.2 [2] [Total: 11]

2021 NovemberPaper 6Question 1Component 62Variant 211 marks
Experimental skills and investigations
Loading original question

1 A student determines the density of a block of wood. (a) Fig. 1.1 shows one face of the block of wood that the student uses. l w Fig. 1.1 (i) Measure the length l and width w of the block of wood. Fig. 1.1 is drawn actual size. l = … cm w = … cm [1] (ii) The student measures the height h of the block of wood. 4.0 h = … cm Calculate the volume V of the block of wood using the equation V = l × w × h. V = … cm3 [1] (iii) The student measures the mass m of the block of wood on a balance. 63.92 g Fig. 1.2 Write down the mass m of the block as shown in Fig. 1.2. Give your answer to the nearest gram. m = … g [1] (iv) Calculate the density ρ of the wood using the equation ρ = m V. Give your answer to a suitable number of significant figures for this experiment and include the unit. ρ = … [2] (b) The student places the block of wood carefully in water in a glass dish. The wood floats as shown in Fig. 1.3. block of wood water surface Fig. 1.3 (i) Using Fig. 1.3, estimate, without taking a measurement, the volume V1 of wood that is below the water surface. V1 = … cm3 [1] (ii) Calculate mW, the mass of water with volume V1, using the equation mW = ρW × V1 , where ρW = 1.00 in the same units as ρ in part (a)(iv). mW = … [1] (c) A student suggests that the mass m of the block of wood should be equal to the mass mW of the water with volume V1. (i) Calculate the difference d between your values of m and mW. d = … [1] (ii) Discuss whether the difference d is small enough to conclude that m = mW.… [1] (d) Another student wants to obtain a more accurate value for V1. He uses the method of floating the block of wood in water as described in (b). Suggest how the student could obtain a more accurate value by taking a measurement.… [2] [Total: 11]

2021 NovemberPaper 6Question 1Component 63Variant 311 marks
Experimental skills and investigations
Loading original question

1 A student investigates the effect of insulation on the cooling of water. She uses the apparatus shown in Fig. 1.1. The sides of beaker A are covered with material that is a thermal insulator. Beaker B has no covering on its sides. bench thermometer 20 30 10 lid beaker A beaker B insulation Fig. 1.1 (a) Record room temperature θR shown on the thermometer in Fig. 1.1. θR = … [1] (b) The student pours 150 cm3 of hot water into beaker A and records the temperature θ at time t = 0. She records, in Table 1.1, the temperature of the water in the beaker every 30 s. The student repeats the process for beaker B. Add units to the column headings in Table 1.1. [1] Table 1.1 beaker A with insulation beaker B without insulation t / θ / θ / 0 88.0 87.5 30 86.0 83.5 60 84.5 81.5 90 83.5 80.0 120 82.5 79.0 150 82.0 78.5 180 81.5 78.0 (c) Describe two precautions that can be taken to ensure that temperature readings in the experiment are as accurate as possible. 1.… 2.… [2] (d) Write a conclusion stating whether the insulation affects the rate of cooling of the water. Justify your answer by reference to values from the results.… [2] (e) (i) Calculate the average cooling rate x1 during the first half of the experiment for the water in beaker B. Use the readings for beaker B from Table 1.1 and the equation x1 = θ0 – θ90 T , where T = 90 s and θ0 and θ90 are the temperatures of the water in beaker B at t = 0 and t = 90 s. Include the unit. x1 = … [1] (ii) Calculate the average cooling rate x2 during the second half of the experiment for the water in beaker B. Use the readings for beaker B from Table 1.1 and the equation x2 = θ90 – θ180 T , where T = 90 s and θ90 and θ180 are the temperatures of the water in beaker B at t = 90 s and t = 180 s. Include the unit. x2 = … [1] (f) (i) Suggest an additional experiment to test whether the lid affects the cooling rate of the water in beaker B. State how the readings are used to show the effect.… [1] (ii) A student suggests that the temperature of the water in beaker B at t = 0 for this additional experiment must be the same as in (b) for the comparison to be fair. State whether your results support this suggestion. Use your results from (e) to explain whether this precaution is necessary. statement … explanation… [2] [Total: 11]

2021 MarchPaper 6Question 2Component 62Variant 211 marks
Experimental skills and investigations
Loading original question

2 Students investigate the cooling of hot water in two different cups. They use the apparatus shown in Fig. 2.1. Cup A is made from thin plastic. The top of cup A has an inside diameter of 7 cm. Cup B is made from expanded polystyrene. The top of cup B has an inside diameter of 8 cm. bench thermometer 20 30 10 lids cup B cup A Fig. 2.1 (a) (i) Record the room temperature θR shown on the thermometer in Fig. 2.1. θR = … [1] (ii) Describe one precaution that you would take to ensure that temperature readings in the experiment are as accurate as possible.… [1] (b) A volume of 100 cm3 of hot water is poured into each cup and the initial temperature θ is recorded in Table 2.1. The temperature of the water in each cup is recorded every 30 s. The values are shown in Table 2.1. Table 2.1 cup A cup B t / θ / θ / 0 87.5 88.0 30 84.5 86.0 60 82.0 84.5 90 80.5 83.0 120 79.0 82.0 150 78.0 81.0 180 77.0 80.5 Complete the headings in Table 2.1. [1] (c) Write a conclusion stating which cup, A or B, is the more effective in reducing the cooling rate of the hot water in this experiment. Justify your answer by reference to the results.… [2] (d) (i) Calculate xA, the average cooling rate for cup A over the whole experiment. Use the readings for cup A from Table 2.1 and the equation xA = θ0 – θ180 T where T = 180 s and θ0 and θ180 are the temperatures at time t = 0 and at time t = 180 s. Include the unit for the cooling rate. xA = … [2] (ii) Suggest an additional experiment to show how the lid affects the cooling rate of cup A. Explain how to use the additional results to show the effect. additional experiment… explanation… [2] (e) A student wishes to compare the effect of the materials of the cups on cooling rates. Suggest two variables that she should control to make this test fair. 1.… 2.… [2] [Total: 11]

2021 JunePaper 6Question 2Component 61Variant 111 marks
Experimental skills and investigations
Loading original question

2 A student investigates resistance. Fig. 2.1 shows the circuit she uses. A V power supply Fig. 2.1 (a) She records the potential difference (p.d.) V1 across the resistor and the current I1 in the circuit. The meters are shown in Fig. 2.2 and Fig. 2.3. (i) Write down the readings. Include the units for potential difference, current or resistance where appropriate in all parts of the question. V 6 7 9 8 10 4 5 2 1 3 0 A 0.6 0.8 1.0 0.4 0.2 0 Fig. 2.2 Fig. 2.3 V1 = … I1 = … [3] (ii) Calculate the resistance R1 of the resistor using the equation R1 = V1 I1 . R1 = … [1] (b) She connects a second resistor in series with the first resistor. She connects the voltmeter across both resistors and records the potential difference V2 across both resistors and the current I2 in the circuit. 2.6 V2 = … 0.28 I2 = … Calculate the resistance RS of the resistors in series using the equation RS = V2 I2 . RS = … [1] (c) She connects the second resistor in parallel with the first resistor. She connects the voltmeter across both resistors. She records the potential difference V3 across the resistors and the current I3 in the circuit. 2.4 V3 = … 0.99 I3 = … Calculate the resistance RP of the resistors in parallel using the equation RP = V3 I3 . Give your answer to a suitable number of significant figures for this experiment. RP = … [1] (d) Complete the circuit diagram to show the circuit she uses in part (c). [2] (e) Describe how to extend part (c) of this experiment to investigate the relationship between the combined resistance of identical resistors connected in parallel and the number of resistors.… [2] (f) In this type of electrical experiment, a variable resistor can be used to vary the current. Draw the circuit symbol for a variable resistor. [1] [Total: 11]

2021 JunePaper 6Question 2Component 62Variant 211 marks
Experimental skills and investigations
Loading original question

2 A student investigates the position of the image in a plane mirror. Fig. 2.1 shows the ray-trace sheet that the student uses. eye M P3 P4 R Fig. 2.1 (a) • The line MR shows the position of a plane mirror. Draw a normal to this line that passes through its centre. Continue the normal so that it reaches the bottom of the ray-trace sheet. Label the normal NL. Label the point at which NL crosses MR with the letter B. • Draw a line CD 5.0 cm below MR and parallel to MR. • Label the point X where CD crosses NL. • Draw a line EF 5.0 cm below CD and parallel to CD. • Label the point Y where EF crosses NL. [2] (b) Draw a line 7.0 cm long from B at an angle of incidence θ1 = 20° to the normal below MR and to the left of the normal. Label the end of this line A. [1] (c) The student places two pins, P1 and P2 , on line AB. Suggest a suitable distance x between the pins for this type of ray-trace experiment. x = … [1] (d) The student views the images of pins P1 and P2 from the direction indicated by the eye in Fig. 2.1. She places pin P3 on line CD so that the images of P2 and P1 appear exactly behind pin P3. She places pin P4 on line EF so that pin P3, and the images of P2 and P1, all appear exactly behind pin P4. The positions of P3 and P4 are shown on Fig. 2.1. (i) Measure and record the distance a from X to P3. a = … [1] (ii) Measure and record the distance b from Y to P4. b = … [1] (iii) Calculate a b . a b = … [1] (e) The student repeats the procedure using an angle of incidence θ2 = 40°. She records the new values of a and b. 4.2 cm a = … 8.3 cm b = … Calculate the new value a b . a b = … [2] (f) State and explain whether the two values of a b can be considered to be equal in this experiment.… [1] (g) A student carries out this experiment with care. Suggest a practical reason why the results may not be accurate.… [1] [Total: 11]

2021 JunePaper 6Question 2Component 63Variant 311 marks
Experimental skills and investigations
Loading original question

2 A student determines the electromotive force (e.m.f.) and resistance of a cell by using a resistance wire. She uses the circuit shown in Fig. 2.1. power supply A resistance wire crocodile clip resistor Q P + – Fig. 2.1 (a) On Fig. 2.1, draw a voltmeter connected to measure the potential difference (p.d.) across terminals P and Q. [1] (b) The switch is closed. The student moves the crocodile clip on the resistance wire so that the potential difference V across terminals P and Q is 5.0 V. She measures the current I for the cell and resistor in series. A 0.6 0.8 1.0 0.4 0.2 0 Fig. 2.2 Read, and record in Table 2.1, the value of I shown on the meter in Fig. 2.2. [1] (c) The student repeats the procedure in (b) for values of V = 4.5 V, 4.0 V, 3.5 V and 3.0 V. Her readings are shown in Table 2.1. Table 2.1 V / V I / A 5.0 4.5 0.56 4.0 0.44 3.5 0.35 3.0 0.28 Plot a graph of I / A (y-axis) against V / V (x-axis). Start both axes at the origin (0,0). 0 0 [4] (d) The e.m.f. E of the cell is equal to the value of V when I = 0.0 A. Determine the value of E from the graph. E = … [1] (e) (i) Determine the gradient G of the graph. Show clearly on the graph how you obtained the necessary information. G = … [1] (ii) The value of 1 G is numerically equal to the resistance (r + R) where r is the resistance of the cell and R = 4.0 Ω. Calculate the resistance r of the cell. r = … Ω [1] (f) Suggest how the experiment and graph could be improved to obtain a more accurate value for e.m.f. E.… [2] [Total: 11]

2021 NovemberPaper 6Question 2Component 61Variant 111 marks
Experimental skills and investigations
Loading original question

2 A student investigates the resistance of resistors in different circuit arrangements. Fig. 2.1 shows the first circuit arrangement. A V X Y power supply Fig. 2.1 (a) She measures the potential difference (p.d.) VX across the resistor X and the current IX in the circuit. The meters are shown in Fig. 2.2 and Fig. 2.3. (i) Write down the readings. Include the units for potential difference, current or resistance where appropriate in all parts of the question. V 6 7 9 8 10 4 5 2 1 3 0 A 0.6 0.8 1.0 0.4 0.2 0 Fig. 2.2 Fig. 2.3 VX = … IX = … [2] (ii) Calculate RX, the resistance of resistor X, using the equation RX = VX IX . RX = … [2] (b) The student connects the voltmeter to record VXY, the potential difference across the two resistors X and Y in series. She calculates RXY, the combined resistance of resistors X and Y connected in series. 10.4 RXY = … She calculates the resistance RY of resistor Y. 5.78 RY = … State and explain whether RX and RY can be considered to be equal within the limits of experimental accuracy.… [1] (c) The student connects a resistor Z in parallel with resistor X. She connects the voltmeter to record VXZ, the potential difference across the parallel combination of resistor X and resistor Z. Draw the circuit diagram for this arrangement. Label the resistors X, Y and Z. [3] (d) The student records VXZ, the potential difference across the two resistors X and Z in parallel, and IXZ, the current in the circuit. 0.8 VXZ = … 0.36 IXZ = … Calculate RXZ, the combined resistance of resistors X and Z connected in parallel, using the equation RXZ = VXZ IXZ . Give your answer to 2 significant figures. RXZ = … [1] (e) Another student does this experiment using a set of three identical resistors. His results show that, within the limits of experimental accuracy, the combined resistance of two identical resistors connected in series is four times the combined resistance of the same two resistors connected in parallel. To test whether his results are true for other values of resistance, he does the same procedure with other sets of three identical resistors. Suggest the values of resistance he could use to reach a conclusion during a 1 hour practical lesson.… [2] [Total: 11]

2021 NovemberPaper 6Question 2Component 62Variant 211 marks
Experimental skills and investigations
Loading original question

2 A student investigates the resistances of a resistor and a lamp. Fig. 2.1 shows the first circuit arrangement. A V R power supply Fig. 2.1 (a) She records VS, the potential difference (p.d.) across the resistor R, and the current IS in the circuit. The meters are shown in Fig. 2.2 and Fig. 2.3. (i) Write down the readings. Include the units for potential difference, current or resistance where appropriate in all parts of the question. V 6 7 9 8 10 4 5 2 1 3 0 A 0.6 0.8 1.0 0.4 0.2 0 Fig. 2.2 Fig. 2.3 VS = … IS = … [2] (ii) Calculate RS, the resistance of resistor R, using the equation RS = VS IS . RS = … [2] (b) The student replaces the resistor with the lamp. She records VL the potential difference across the lamp and the current IL in the circuit. 1.7 VL= … 0.35 IL = … Calculate RL, the resistance of the lamp, using the equation RL = VL IL . RL = … [2] (c) The student connects the resistor R in series with the lamp. She connects the voltmeter to record VC, the potential difference across the series combination of the resistor and the lamp. Draw the circuit diagram for this arrangement. [2] (d) The student records VC the potential difference across the resistor and the lamp in series and the current IC in the circuit. 1.7 VC = … 0.21 IC = … Calculate RC, the combined resistance of the resistor and the lamp connected in series, using the equation RC = VC IC . RC = … [1] (e) State and explain briefly whether the results show that RS + RL = RC within the limits of experimental accuracy. statement … explanation… [2] [Total: 11]

2021 NovemberPaper 6Question 2Component 63Variant 311 marks
Experimental skills and investigations
Loading original question

2 A student compares the resistances of two wires. She uses the circuit, part of which is shown in Fig. 2.1. resistance wire A resistance wire B crocodile clip l X Y Fig. 2.1 (a) On Fig. 2.1, complete the circuit diagram to show a voltmeter connected to measure the potential difference (p.d.) across terminals X and Y, and an ammeter connected to measure the current in the circuit. [2] (b) The student connects the crocodile clip to a length l = 90.0 cm of resistance wire A and measures the potential difference V and the current I for the length l of the wire. V 3 4 5 2 1 0 A 0.6 0.8 1.0 0.4 0.2 0 Fig. 2.2 Fig. 2.3 (i) Read, and record in Table 2.1, the values of V and I shown on the meters in Fig. 2.2 and Fig. 2.3. [2] Table 2.1 wire l / cm V / I / R / A 90.0 B 90.0 2.6 0.45 A 50.0 2.7 0.54 B 50.0 2.3 0.72 (ii) The student then connects the crocodile clip to lengths l = 90.0 cm of wire B, l = 50.0 cm of wire A and l = 50.0 cm of wire B. Her readings are shown in Table 2.1. Calculate, and record in Table 2.1, the resistance R of each length of wire A and wire B. Use the values of V and I and the equation R = V I . [2] (iii) Complete the headings in Table 2.1. [1] (c) (i) Calculate a value P using your results from Table 2.1 and the equation P = R for 90.0 cm of wire A R for 90.0 cm of wire B. P = … Calculate a value Q using your results from Table 2.1 and the equation Q = R for 50.0 cm of wire A R for 50.0 cm of wire B. Q = … [1] (ii) A student suggests that the values of P and Q should be equal. State whether your results support this suggestion. Justify your answer by reference to values from your results. statement … justification… [2] (d) Suggest one reason why students all doing this experiment carefully with the same apparatus may not obtain the same results.… [1] [Total: 11]

2021 MarchPaper 6Question 3Component 62Variant 211 marks
Experimental skills and investigations
Loading original question

3 A student investigates a resistor and a lamp connected in series. She uses the circuit shown in Fig. 3.1. power supply resistance wire crocodile clip V A Fig. 3.1 (a) The student moves the crocodile clip on the resistance wire so that the value of the potential difference VL across the lamp is 2.0 V. She measures the current I for the lamp and resistor in series. She then connects the voltmeter to measure the potential difference VR across the resistor. A 0.6 0.8 1.0 0.4 0.2 0 V 3 4 5 2 1 0 Fig. 3.2 Fig. 3.3 Read, and record in Table 3.1, the values of I and VR shown on the meters in Fig. 3.2 and Fig. 3.3. [2] (b) The student repeats the steps in (a) for values of VL = 1.0 V and VL = 0.5 V. Her readings are shown in Table 3.1. Table 3.1 VL / V I / A VR / V RL / Ω RR / Ω 2.0 1.0 0.15 3.0 0.5 0.12 2.4 Calculate, and record in Table 3.1, the resistance of the lamp RL for each value of VL. Use the values of VL and I from Table 3.1 and the equation RL = VL I . Calculate, and record in Table 3.1, the resistance of the resistor RR for each value of VL. Use the values of VR and I from Table 3.1 and the equation RR = VR I . [2] (c) (i) Describe the pattern of any change in the value of RL as VL decreases.… [1] (ii) A student suggests that RR should be constant. State whether your results support this suggestion. Justify your statement by reference to values from Table 3.1. statement… justification… [2] (d) A student wishes to determine the resistance of the lamp RL when the potential difference across the lamp VL = 0.0 V. Describe how the experiment can be extended to do this with the help of a suitable graph.… [2] (e) It is possible to use a variable resistor instead of a resistance wire to change the potential difference across the lamp. Complete the circuit in Fig. 3.4 to show: • a variable resistor used for this purpose • the voltmeter connected to measure the potential difference across the resistor power supply A Fig. 3.4 [2] [Total: 11]

2021 JunePaper 6Question 3Component 61Variant 111 marks
Experimental skills and investigations
Loading original question

3 A student investigates the refraction of light through a transparent block. Fig. 3.1 shows the transparent block ABCD on the student’s ray-trace sheet. eye D A C P3 P4 B Fig. 3.1 (a) • Draw a normal at the centre of side AB. Continue the normal so that it reaches the bottom of the ray-trace sheet. Label the normal NL. • Label the point Q where NL crosses AB. [1] (b) • Draw a line EF parallel to CD and 2.0 cm below CD. • Label the point J where NL crosses EF. • Draw a line GH parallel to CD and 7.0 cm below CD. • Label the point K where NL crosses GH. [1] (c) (i) Draw a line PQ at an angle i = 30° to the normal and on the left-hand side of the normal above the block. [1] (ii) The student places two pins P1 and P2 on line PQ. Fig. 3.1 is not drawn full size. Suggest a suitable distance apart for pins P1 and P2 in this type of experiment. distance apart … [1] (d) The student observes the images of P1 and P2 through side CD of the block. She adjusts her line of sight until the images of P1 and P2 appear one behind the other. She places a pin P3 on line EF and a pin P4 on line GH so that P3, and the images of P1 and P2 seen through the block, appear behind pin P4. (i) On Fig. 3.1, measure the length a of the line from J to P3. a = … [1] (ii) On Fig. 3.1, measure the length b of the line from K to P4. b = … [1] (iii) Calculate b a . b a = … [2] (e) State one precaution that you would take in this type of experiment in order to produce an accurate ray trace.… [1] (f) A student plans to test the suggestion that, in this experiment, b a is a constant for all possible values of i. List suitable values of i that the student could use. … [2] [Total: 11]

2021 JunePaper 6Question 3Component 62Variant 211 marks
Experimental skills and investigations
Loading original question

3 A student investigates resistance. Fig. 3.1 shows the circuit used. power supply A V resistance wire sliding contact S D B C l R Fig. 3.1 (a) The student measures the current I in the circuit. He places the sliding contact S at C and measures the potential difference (p.d.) V1 across the resistor R. The voltmeter and ammeter are shown in Fig. 3.2 and Fig. 3.3. V 3 4 5 2 1 0 A 0.6 0.8 1.0 0.4 0.2 0 Fig. 3.2 Fig. 3.3 (i) Write down the readings. Include the units for potential difference, current or resistance where appropriate in all parts of the question. V1 = … I1 = … [2] (ii) Calculate the resistance R1 of the resistor using the equation R1 = V1 I1 . R1 = … [2] (b) The student disconnects the voltmeter from terminal B and connects the voltmeter to terminal C. He places the sliding contact S at a distance l = 20.0 cm from C. He records, in Table 3.1, the reading on the voltmeter. He repeats the procedure using l = 40.0 cm, 60.0 cm, 80.0 cm and 100.0 cm. His readings are shown in Table 3.1. Table 3.1 l / cm V / V 20.0 0.4 40.0 0.8 60.0 1.1 80.0 1.5 100.0 1.9 Plot a graph of V / V (y-axis) against l / cm (x-axis). Start both axes at the origin (0,0). 00 [4] (c) Use your value of V1 from (a)(i) to find the length l R of resistance wire that has the same resistance as resistor R. Show clearly on the graph how you obtained the necessary information. l R = … cm [2] (d) The resistance of the resistance wire is proportional to its length. Estimate the resistance of 100 cm of the resistance wire. estimate … [1] [Total: 11]

2021 JunePaper 6Question 3Component 63Variant 311 marks
Experimental skills and investigations
Loading original question

3 A student investigates the refraction of light by a transparent block. He uses his results to determine a quantity known as the refractive index of the material of the block. The student’s ray-trace sheet is shown full size in Fig. 3.1. E N A D C B P1 P4 P6 P3 P5 P2 Fig. 3.1 (a) The student places a transparent block ABCD near the centre of the ray-trace sheet, as indicated in Fig. 3.1. (i) Draw a normal at point N, extending above AB. Label the upper end of the normal with the letter L. Extend the normal downwards until it crosses line CD. Label the point at which it crosses CD with the letter F. [1] (ii) The student draws line EN as shown in Fig. 3.1. On Fig. 3.1, measure the angle θ1 between the lines LN and EN. θ1 = … [1] (b) The student places two pins, P1 and P2, on line EN, as shown in Fig. 3.1. Suggest whether the two pins are a suitable distance apart for accurate ray tracing. Explain your answer. statement … explanation… [1] (c) The student views the images of P1 and P2 through the block. He places two pins, P3 and P4, so that pins P3 and P4, and the images of P1 and P2, all appear exactly one behind the other. • Draw a line through P3 and P4, extending the line until it meets NF. • Label the point at which this line meets NF with the letter G. • Label the point at which this line crosses CD with the letter H. • Draw a line joining points N and H. [1] (d) (i) Measure the length a of line NH. a = … cm Measure the length b of line GH. b = … cm [1] (ii) Calculate a value n for the refractive index, using the equation n = a b . n = … [2] (e) The student repeats the above procedure for an angle θ2 = 40°. He places two pins, P5 and P6, so that pins P5 and P6, and the images of P1 and P2, all appear exactly one behind the other. • Draw a line through pins P5 and P6. Extend the line until it meets GH. • Label the point at which this line meets GH with the letter K. • Label the point at which this line crosses CD with the letter R. (i) Measure the angle α, where α is the smaller angle between lines RK and GH. α = … [1] (ii) A student suggests that the angle α should be equal to the difference between the angle θ2 from (e) and the angle θ1 from (a)(ii). State whether your results support this suggestion. Justify your answer by reference to your results. statement … justification… [1] (f) Suggest a precaution which should be taken to ensure accurate results in this type of experiment.… [1] (g) Suggest why different students, all carrying out this experiment carefully, may not obtain identical results.… [1] [Total: 11]

2021 NovemberPaper 6Question 3Component 61Variant 111 marks
Experimental skills and investigations
Loading original question

3 A student investigates the position of the image in a plane mirror. Fig. 3.1 shows the ray-trace sheet. M R P5 P3 P6 P4 Fig. 3.1 (a) • On Fig. 3.1, draw a normal to the line MR that passes through its centre. Label the normal NL. Label the point at which NL crosses MR with the letter B. • Draw a line 7.0 cm long from B at an angle of incidence i = 70° to the normal below MR and to the left of the normal. Label the end of this line A. • Draw another line 7.0 cm long from B at an angle θ = 40° to the normal below MR and to the left of the normal. Label the end of this line C. [3] (b) Mark, with two neat crosses, positions for two pins, P1 and P2, on line AB at a suitable distance apart for this type of ray-trace experiment. [1] (c) The student places a plane mirror on line MR and views the images of pins P1 and P2 in the mirror. He places two pins, P3 and P4, so that pins P3 and P4 and the images of P2 and P1 all appear exactly one behind the other. The positions of P3 and P4 are marked on Fig. 3.1. Draw a line through the positions of P3 and P4. Continue the line until it meets MR. Measure the angle α between the line and the normal NL below MR. Include the unit. α = … [1] (d) The student places the reflecting face of the mirror vertically on the line AB with the centre of the mirror at B. He places pins P1 and P2 on line CB. He places pins P5 and P6 so that pins P5 and P6 and the images of P2 and P1 all appear exactly one behind the other. Draw a line through the positions of P5 and P6. Continue the line until it meets NL. Measure the angle β between the line and NL below MR. Include the unit. β = … [1] (e) A student investigates a possible relationship between angles α and β. The angle θ remains constant at θ = 40°. Suggest values of the angle of incidence i that he could use.… [2] (f) A student does this experiment with care. Suggest one practical reason why the results may not be exactly those that the theory of reflection predicts.… [1] (g) Tick the boxes that indicate relevant precautions that the student should take with this type of ray-trace experiment. carry out the experiment in a darkened room draw thin lines keep one eye closed keep room temperature constant view the bases of the pins view the tops of the pins [2] [Total: 11]

2021 NovemberPaper 6Question 3Component 62Variant 211 marks
Experimental skills and investigations
Loading original question

3 A student investigates the image produced by a lens. Fig. 3.1 shows the apparatus. illuminated object u v lens screen bench Fig. 3.1 (a) • The student places the lens a distance u = 20.0 cm from the illuminated object. • He moves the screen until a clearly focused image is formed on the screen. • He measures the distance v between the centre of the lens and the screen. • Calculate, and record in the first row of Table 3.1, u v . • He repeats the procedure for u = 25.0 cm, u = 30.0 cm, u = 35.0 cm and u = 40.0 cm. The readings and results are shown in Table 3.1. Table 3.1 u / cm v / cm u v 20.0 79.5 25.0 44.5 0.56 30.0 35.0 0.86 35.0 30.0 1.17 40.0 27.0 1.48 [1] (b) Plot a graph of u / cm (y-axis) against u v (x-axis). Start the y-axis at u = 15.0 cm. [4] (c) Use your graph to find u1, the value of u when u v = 1.0. Show clearly on the graph how you obtained the necessary information. u1 = … [2] (d) Calculate the focal length f of the lens using the equation f = u1 2 . Give your answer to a suitable number of significant figures for this experiment. f = … cm [2] (e) Suggest one practical difficulty with this experiment. Explain briefly how you would try to overcome this difficulty in order to obtain accurate results. suggestion… explanation… [2] [Total: 11]

Full Paper 6 past papers with mark schemes

Paper 6: quick facts

Which topics come up most in IGCSE Physics 0625 Paper 6?

The most-tagged topics in IGCSE Physics 0625 Paper 6 are Experimental skills and investigations (212), Electricity and magnetism (24) and Waves (22), out of 212 past-paper questions from 2019-2026. These are archive counts, not a prediction, and a question can carry more than one topic.

Are the IGCSE Physics 0625 Paper 6 questions free?

84 of the 212 IGCSE Physics 0625 Paper 6 questions are free to practise. The other 128 need a plan for IGCSE Physics 0625, from $6 a month.

Do the IGCSE Physics 0625 Paper 6 questions have answers?

Yes. Each IGCSE Physics 0625 Paper 6 question shows the official mark scheme answer. Many also have a step-by-step worked explanation written by PastPaperPrep.