IGCSE Physics 0625 · Paper practice

Paper 5 past paper questions

Every archived Physics 0625 Paper 5 question in one place. Practise them by topic, then sit a full paper under timed conditions.

Most-tested topicsExperimental skills and investigations 212Electricity and magnetism 26Waves 21Motion, forces and energy 16Thermal physics 10

Course route
Sort questions

You’re practising 2019–2021 papers. The 2022–2026 papers, including 2026, need a plan.

Unlock from $6/mo
24 free questions

2021 MarchPaper 5Question 1Component 52Variant 211 marks
Experimental skills and investigations
Loading original question

1 In this experiment, you will investigate the motion of an oscillating metre rule. Carry out the following instructions, referring to Fig. 1.1. clamps vertical threads stands d metre rule horizontal bench l Fig. 1.1 (a) Ensure that the metre rule is horizontal. You may need to adjust the height of one of the clamps slightly. Briefly describe how you check that the metre rule is horizontal. You may draw a diagram or add to Fig. 1.1 if it helps to explain your answer.… [1] Do not change the length l of the threads during the experiment. (b) Move one thread to the 40.0 cm mark on the metre rule and one thread to the 60.0 cm mark on the metre rule. The distance d between the threads is 20.0 cm. Move the stands so that the threads remain vertical. Hold each end of the metre rule. Twist the metre rule a small amount, as shown in Fig. 1.2, and then let it go so that it oscillates in a rotating motion. metre rule seen from above twist one oscillation Fig. 1.2 Measure, and record in Table 1.1, the time t for 5 complete oscillations of the metre rule. Repeat this procedure for d values of 30.0 cm, 40.0 cm, 50.0 cm and 60.0 cm. For each value, the threads must be at equal distances either side of the 50.0 cm mark on the metre rule. Table 1.1 d / cm t / s 1 T / 1 s 20.0 30.0 40.0 50.0 60.0 [2] (c) For each value of the distance d, calculate and record in Table 1.1, the value of 1 T where T is the time for 1 oscillation of the metre rule. Use your values of time t from Table 1.1 and the equation 1 T = 5 t . [1] (d) Plot a graph of distance d / cm (y-axis) against 1 T / 1 s (x-axis). [4] (e) Determine the gradient G of the graph. Show clearly on the graph how you obtained the necessary information. G = … [1] (f) (i) Explain why it is more accurate to measure the time for 5 oscillations rather than for 1 oscillation.… [1] (ii) Describe how the experiment could be improved to make the readings more reliable.… [1] [Total: 11]

2021 JunePaper 5Question 1Component 51Variant 111 marks
Experimental skills and investigations
Loading original question

1 In this experiment, you will investigate the period of a pendulum. Carry out the following instructions, referring to Fig. 1.1 and Fig. 1.2. x d split cork floor bob split cork one complete oscillation Fig. 1.1 Fig. 1.2 A pendulum has been set up for you as shown in Fig. 1.1. (a) Measure the distance d between the bottom of the split cork and the floor. d = … cm [1] This distance d must remain constant throughout the experiment. (b) • Adjust the length of the pendulum until the distance x, measured from the centre of the bob to the floor, is 50.0 cm. • Displace the bob slightly and release it so that it swings. Fig. 1.2 shows one complete oscillation of the pendulum. • Measure, and record in Table 1.1, the time t for 10 complete oscillations. • Calculate, and record in Table 1.1, the period T of the pendulum. The period is the time for one complete oscillation. • Calculate, and record in Table 1.1, T 2. [2] Table 1.1 x / cm t / s T / s T 2 / s2 50.0 45.0 40.0 35.0 30.0 (c) Repeat the procedure in (b) using x = 45.0 cm, 40.0 cm, 35.0 cm and 30.0 cm. [3] (d) Plot a graph of T 2 / s2 (y-axis) against x / cm (x-axis). You do not need to start your axes at the origin (0,0). [4] (e) Explain why timing 10 oscillations gives a more accurate result for the period T than timing one oscillation.… [1] [Total: 11]

2021 JunePaper 5Question 1Component 52Variant 211 marks
Experimental skills and investigations
Loading original question

1 In this experiment, you will determine the density of sand. Carry out the following instructions, referring to Fig. 1.1. The beaker labelled A has a mark at the 250 cm3 level. h beaker A Fig. 1.1 (not to scale) (a) Estimate the volume of water VW that beaker A would hold when filled to the top. VW = … cm3 [1] (b) (i) Use the string and the metre rule provided to accurately determine the circumference c of beaker A. Record your readings and show your working. c = … cm [2] (ii) Explain briefly how you used the string and the metre rule to determine c as accurately as possible. You may draw a diagram.… [2] (c) Measure the height h of beaker A, as shown in Fig. 1.1. h … cm Calculate the volume VA of beaker A using the equation VA = hc 2 12.6 . VA = … cm3 [2] (d) (i) Beaker B contains dry sand. Pour the sand into the measuring cylinder. • Record the volume VS of sand. VS = … cm3 • Write down the mass mB of beaker B, given on the card. mB = … g • Pour the sand into beaker B. Measure the mass m of beaker B containing the sand. m = … g • Calculate the mass mS of sand in the beaker. Use the equation mS = (m – mB). mS = … g [2] (ii) Calculate the density ρ of sand using the equation ρ = mS VS . Include the unit. ρ = … [2] [Total: 11]

2021 JunePaper 5Question 1Component 53Variant 311 marks
Experimental skills and investigations
Loading original question

1 In this experiment, you will investigate the behaviour of a spring and use it to determine the density of modelling clay. A stand and spring have been set up for you. Carry out the following instructions, referring to Fig. 1.1 and Fig. 1.2. clamp spring l 0 Fig. 1.1 (a) Measure the length l0 of the spring without any load. l0 = … cm [1] (b) Suspend a load of weight W = 2.0 N from the spring, as shown in Fig. 1.2. clamp spring load l Fig. 1.2 (i) Measure the stretched length l of the spring. l = … cm [1] (ii) Calculate the extension e of the spring for a load of weight W = 2.0 N. Use your values from (a) and (b)(i) and the equation e = (l – l0). e = … cm [1] (c) Remove the load from the spring. Suspend the load U, which is made of modelling clay, from the spring. Measure the stretched length lU of the spring. lU = … cm Calculate the extension eU of the spring with load U. eU = … cm The extension of a spring is directly proportional to the weight of the load. Use your values of W and e from (b)(ii) and your value of eU to determine the weight WU of load U. Show your working. WU = … [2] (d) Fully immerse load U in the beaker of water, as shown in Fig. 1.3. The load U must not touch either the sides or the bottom of the beaker. clamp spring load U bench lW beaker water Fig. 1.3 Measure the stretched length lW of the spring. lW = … cm Calculate the extension eW of the spring with load U in the water. eW = … cm Calculate the density ρ of the modelling clay. Use your value of eU from (c), your value of e W and the equation ρ = eU (eU – e W) × k , where k = 1.0 g / cm3. ρ = … g / cm3 [2] (e) Suggest a possible source of inaccuracy in the determination of ρ in this experiment.… [1] (f) Describe one precaution that you took when measuring the length of the spring, to ensure an accurate reading. You may draw a diagram.… [1] (g) A student plots a graph of load against extension for the spring, to show that the two quantities are directly proportional. State how his graph line shows that load and extension are directly proportional.… [2] [Total: 11]

2021 NovemberPaper 5Question 1Component 51Variant 111 marks
Experimental skills and investigations
Loading original question

1 In this experiment, you will investigate the stretching of a spring. Carry out the following instructions, referring to Fig. 1.1. spring metre rule 0 cm mark 100 cm mark boss clamp clamp stand bench Fig. 1.1 (a) The metre rule is clamped in position near to the spring. Do not change the position of the metre rule. (i) Write down the scale readings in mm from the metre rule at the top and bottom of the spring. top reading = … mm bottom reading = … mm [1] (ii) Using the two readings, calculate the length l0 of the spring in mm. Record l0 in Table 1.1. The value l0 is the length of the spring when the load L = 0.00 N. [1] (b) • Suspend a load L = 0.20 N from the spring. Record the new length l of the spring in Table 1.1. • Use the equation e = (l – l0) to calculate the extension e of the spring. Record the value of e in Table 1.1. • Repeat the procedure using loads L = 0.40 N, L = 0.60 N, L = 0.80 N and L = 1.00 N. Record all the readings and results in the Table 1.1. Table 1.1 L / N l / mm e / mm 0.00 0 0.20 0.40 0.60 0.80 1.00 [3] (c) Plot a graph of e / mm (y-axis) against L / N (x-axis). [4] (d) Fig. 1.2 shows the unstretched spring and the spring with a load. On Fig. 1.2, show clearly the distances l0, l and e. Fig. 1.2 [2] [Total: 11]

2021 NovemberPaper 5Question 1Component 52Variant 211 marks
Experimental skills and investigations
Loading original question

1 In this experiment, you will determine the density of a block of wood. (a) (i) Measure the length l, width w and height h of the block of wood. l = … cm w = … cm h = … cm [1] (ii) Calculate the volume V of the block of wood using the equation V = l × w × h. V = … cm3 [1] (iii) Measure the mass m of the block of wood using the balance provided. m = … g [1] (iv) Calculate the density ρ of the wood using the equation ρ = m V. Give your answer to a suitable number of significant figures for this experiment and include the unit. ρ = … [2] (b) Place the block of wood, largest face down, carefully in the water in the container. (i) Estimate, without taking a measurement, the volume V1 of wood that is below the water surface. V1 = … cm3 [1] (ii) Calculate mW , the mass of water with volume V1, using the equation mW = ρW × V1, where ρW = 1.00 in the same units as ρ in part (a)(iv). mW = … [1] (c) A student suggests that the mass m of the block of wood is equal to the mass mW of the water with volume V1. (i) Calculate the difference d between your values of m and mW. d = … [1] (ii) Discuss whether the difference d is small enough to conclude that m = mW.… [1] (d) Another student wants to obtain a more accurate value for V1. He uses the method of floating the block of wood in water as described in (b). Suggest how the student could obtain a more accurate value by taking a measurement. You are not required to do this part of the experiment.… [2] [Total: 11]

2021 NovemberPaper 5Question 1Component 53Variant 311 marks
Experimental skills and investigations
Loading original question

1 In this experiment, you will investigate the effect of insulation on the cooling of water. Carry out the following instructions, referring to Fig. 1.1. Beaker A is covered with material that is a thermal insulator. Beaker B is identical to beaker A but has no insulation. bench thermometer lid beaker A beaker B insulation Fig. 1.1 (a) • Remove the lid from beaker A. • Pour 150 cm3 of hot water into beaker A and replace the lid. • Place the thermometer in the water in beaker A. In the first row of Table 1.1, record the temperature θ of the water at t = 0 and immediately start the stop-clock. Record, in Table 1.1, the temperature θ of the water at times t = 30 s, t = 60 s, t = 90 s, t = 120 s, t = 150 s and t = 180 s. [1] • Remove the thermometer from the beaker. (b) (i) Repeat (a) for beaker B. [2] (ii) Add units to the column headings in Table 1.1. [1] Table 1.1 beaker A with insulation beaker B without insulation t / θ / θ / 0 30 60 90 120 150 180 (c) Write a conclusion stating whether the insulation affects the rate of cooling of the water. Justify your answer by reference to values from your results.… [2] (d) (i) Calculate the average cooling rate x1 during the first half of the experiment for the water in beaker B. Use your readings for beaker B from Table 1.1 and the equation x1 = θ0 – θ90 T , where T = 90 s and θ0 and θ90 are the temperatures of the water in beaker B at t = 0 and t = 90 s. Include the unit. x1 = … [1] (ii) Calculate the average cooling rate x2 during the second half of the experiment for the water in beaker B. Use your readings for beaker B from Table 1.1 and the equation x2 = θ90 – θ180 T , where T = 90 s and θ90 and θ180 are the temperatures of the water in beaker B at t = 90 s and t = 180 s. Include the unit. x2 = … [1] (e) (i) Suggest an additional experiment to test whether the lid affects the cooling rate of the water in beaker B. State how the readings are used to show the effect. You are not required to carry out this additional experiment.… [1] (ii) A student suggests that the temperature of the water in beaker B at t = 0 for this additional experiment must be the same as in (b)(i) for the comparison to be fair. State whether your results support this suggestion. Use your results from (d) to explain whether this precaution is necessary. statement … explanation… [2] [Total: 11]

2021 MarchPaper 5Question 2Component 52Variant 211 marks
Experimental skills and investigations
Loading original question

2 In this experiment, you will investigate the cooling of hot water in two different cups. Carry out the following instructions, referring to Fig. 2.1. bench thermometer lids cup B cup A Fig. 2.1 (a) (i) Remove the lid from cup A. Pour 75 cm3 of hot water into cup A and replace the lid. Place the thermometer in the water in cup A. In the first row of Table 2.1, record the temperature θ of the water at time t = 0 and immediately start the stop-clock. Record, in Table 2.1, the temperature θ of the water at times t = 30 s, 60 s, 90 s, 120 s, 150 s and 180 s. [1] (ii) Repeat the steps in (a)(i) for cup B. [2] (b) Table 2.1 cup A cup B t / θ / θ / 0 30 60 90 120 150 180 Complete the headings in Table 2.1. [1] (c) Write a conclusion stating which cup, A or B, is the more effective in reducing the cooling rate of the hot water in this experiment. Justify your answer by reference to your results.… [2] (d) (i) Calculate xA, the average cooling rate for cup A over the whole experiment. Use your readings for cup A from Table 2.1 and the equation xA = θ0 – θ180 T where T = 180 s and θ0 and θ180 are the temperatures at time t = 0 and at time t = 180 s. Include the unit for the cooling rate. xA = … [2] (ii) Suggest an additional experiment to show how the lid affects the cooling rate of cup A. Explain how to use the additional results to show the effect. You are not required to carry out this experiment. additional experiment… explanation… [2] (e) A student wishes to compare the effect of the materials of the cups on cooling rates. Suggest one variable that she should control to make this test fair.… [1] [Total: 11]

2021 JunePaper 5Question 2Component 51Variant 111 marks
Experimental skills and investigations
Loading original question

2 In this experiment, you will investigate resistance. Carry out the following instructions, referring to Fig. 2.1. The circuit has been set up for you. A V power supply Fig. 2.1 (a) Close the switch. (i) Record the current I1 in the circuit. I1 = … [1] (ii) Record the potential difference (p.d.) V1 across the resistor. V1 = … [1] Open the switch. (iii) Calculate the resistance R1 of the resistor using the equation R1 = V1 I1 . R1 = … [1] (b) Disconnect the voltmeter. Connect the second resistor provided in series with the first resistor. Connect the voltmeter across both resistors. Close the switch. • Record the current I2 in the circuit. I2 = … • Record the potential difference (p.d.) V2 across the resistors. V2 = … Open the switch. • Calculate the resistance RS of the resistors in series using the equation RS = V2 I2 . RS = … [2] (c) Disconnect the voltmeter. Connect the second resistor in parallel with the first resistor. Connect the voltmeter across both resistors. Close the switch. • Record the current I3 in the circuit. I3 = … • Record the potential difference (p.d.) V3 across the resistors. V3 = … Open the switch. • Calculate the resistance RP of the resistors in parallel using the equation RP = V3 I3 . RP = … [2] (d) Complete the circuit diagram to show the circuit you used in part (c). [2] (e) Describe how you would extend part (c) of this experiment to investigate the relationship between the combined resistance of identical resistors connected in parallel and the number of resistors. You are not required to do this investigation.… [2] [Total: 11]

2021 JunePaper 5Question 2Component 52Variant 211 marks
Experimental skills and investigations
Loading original question

2 In this experiment, you will investigate the position of the image in a plane mirror. Carry out the following instructions. Use the ray-trace sheet supplied, referring to Fig. 2.1 for guidance. eye hole B A N L R D F M C X Y E θ 8.0 cm 8.0 cm Fig. 2.1 (a) • Draw a line 10 cm long near the top of the ray-trace sheet. Label the line MR. Draw a normal to this line that passes through its centre. Label the normal NL. Label the point at which NL crosses MR with the letter B. • Draw a line CD 8.0 cm below MR and parallel to MR. • Label the point X where CD crosses NL. • Draw a line EF 8.0 cm below CD and parallel to CD. • Label the point Y where EF crosses NL. [2] (b) • Draw a line 7.0 cm long from B at an angle of incidence θ1 = 20° to the normal below MR and to the left of the normal. Label the end of this line A. • Place two pins, P1 and P2, on line AB at a suitable distance apart for this type of ray-trace experiment. [2] (c) Place the reflecting face of the mirror vertically on the line MR. View the images of pins P1 and P2 from the direction indicated by the eye in Fig. 2.1. Place pin P3 on line CD so that the images of P2 and P1 appear exactly behind pin P3. Label the position of P3. Place pin P4 on line EF so that pin P3, and the images of P2 and P1, all appear exactly behind pin P4. Label the position of P4. [1] (d) (i) Measure and record the distance a from X to P3. a = … [1] (ii) Measure and record the distance b from Y to P4. b = … [1] (iii) Calculate a b. a b = … [1] (e) • Repeat the steps in parts (b) and (c) using an angle of incidence θ2 = 10°. • Measure and record the distance c from X to P3. c = … • Measure and record the distance d from Y to P4. d = … • Calculate c d. c d = … [1] (f) State and explain whether the values of a b and c d can be considered to be equal in this experiment.… [1] (g) A student carries out this experiment with care. Suggest a practical reason why the results may not be accurate.… [1] Tie your ray-trace sheet into this booklet between pages 4 and 5. [Total: 11]

2021 JunePaper 5Question 2Component 53Variant 311 marks
Experimental skills and investigations
Loading original question

2 In this experiment, you will determine the electromotive force (e.m.f.) and resistance of a cell by using a resistance wire. The circuit has been set up for you. Carry out the following instructions, referring to Fig. 2.1. power supply V A resistance wire crocodile clip resistor Fig. 2.1 (a) Close the switch. Attach the crocodile clip to the resistance wire. Adjust its position until the value V of the potential difference (p.d.) across the cell and the resistor is 5.0 V. Measure, and record in Table 2.1, the value of the current I for the cell and resistor in series. Repeat this procedure for values of V = 4.5 V, 4.0 V, 3.5 V and 3.0 V. Detach the crocodile clip from the resistance wire. Open the switch. Table 2.1 V / V I /A 5.0 4.5 4.0 3.5 3.0 [2] (b) Plot a graph of I / A (y-axis) against V / V (x-axis). Start both axes at the origin (0,0). 0 0 [4] (c) The e.m.f. E of the cell is equal to the value of V when I = 0.0 A. Determine the value of E from the graph. E = … [1] (d) (i) Determine the gradient G of the graph. Show clearly on the graph how you obtained the necessary information. G = … [1] (ii) The value of 1 G is numerically equal to the resistance (r + R) where r is the resistance of the cell and R = 5.0 Ω. Calculate the resistance r of the cell. r = … Ω [1] (e) Suggest how the experiment and graph could be improved to obtain a more accurate value for e.m.f. E.… [2] [Total: 11]

2021 NovemberPaper 5Question 2Component 51Variant 111 marks
Experimental skills and investigations
Loading original question

2 In this experiment, you will investigate the resistance of combinations of resistors. Fig. 2.1 shows the first circuit arrangement. The circuit is set up for you. A V X Y power supply Fig. 2.1 (a) Switch on. (i) Record VX, the potential difference (p.d.) across resistor X. VX = … [1] (ii) Record IX, the current in the circuit and then switch off the power supply. IX = … [1] (iii) Calculate RX, the resistance of resistor X, using the equation RX = VX IX . RX = … [1] (b) Disconnect the voltmeter. Reconnect the voltmeter to measure VXY, the potential difference across the two resistors X and Y in series. Switch on. (i) Record VXY. VXY = … Record IXY, the current in the circuit and then switch off the power supply. IXY = … [1] (ii) Calculate RXY, the combined resistance of resistors X and Y connected in series, using the equation RXY = VXY IXY . RXY = … [1] (c) Disconnect the voltmeter. Connect resistor Z in parallel with resistor X. Connect the voltmeter to measure VXZ, the potential difference across the parallel combination of resistor X and resistor Z. (i) Draw the circuit diagram for this arrangement. Label the resistors X, Y and Z. [2] (ii) Switch on. Record VXZ, the potential difference across the two resistors X and Z in parallel. VXZ = … Record IXZ, the current in the circuit and then switch off the power supply. IXZ = … [1] (iii) Calculate RXZ, the combined resistance of resistors X and Z connected in parallel, using the equation RXZ = VXZ IXZ . RXZ = … [1] (d) A student does this experiment using a set of three identical resistors. Her results show that, within the limits of experimental accuracy, the combined resistance of two identical resistors connected in series is four times the combined resistance of the same two resistors connected in parallel. To test whether her results are true for other values of resistance, she does the same procedure with other sets of three identical resistors. Suggest the values of resistance she could use to reach a conclusion during a 1 hour practical lesson.… [2] [Total: 11]

2021 NovemberPaper 5Question 2Component 52Variant 211 marks
Experimental skills and investigations
Loading original question

2 In this experiment, you will investigate the resistances of a resistor and a lamp. Fig. 2.1 shows the first circuit arrangement. The circuit has been set up for you. A V R power supply Fig. 2.1 (a) Switch on. (i) Record VS, the potential difference (p.d.) across resistor R. VS = … [1] (ii) Record IS , the current in the circuit and then switch off the power supply. IS = … [1] (iii) Calculate RS, the resistance of resistor R, using the equation RS = VS IS . RS = … [1] (b) • Disconnect the voltmeter. • Replace the resistor with the lamp. • Connect the voltmeter across the lamp. • Switch on. (i) Record VL, the potential difference across the lamp. VL= … Record IL, the current in the circuit and then switch off the power supply. IL = … [1] (ii) Calculate RL, the resistance of the lamp, using the equation RL = VL IL . RL = … [1] (c) • Disconnect the voltmeter. • Connect the resistor R in series with the lamp. • Connect the voltmeter to record VC, the potential difference across the series combination of the resistor and the lamp. (i) Draw the circuit diagram for this arrangement. [2] (ii) Switch on. Record VC, the potential difference across the resistor and the lamp in series. VC = … Record IC, the current in the circuit and then switch off the power supply. IC = … [1] (iii) Calculate RC, the combined resistance of the resistor and the lamp connected in series, using the equation RC = VC IC . RC = … [1] (d) State and explain briefly whether your results show that RS + RL = RC within the limits of experimental accuracy. statement … explanation… [2] [Total: 11]

2021 NovemberPaper 5Question 2Component 53Variant 311 marks
Experimental skills and investigations
Loading original question

2 In this experiment, you will compare the resistances of two wires. The circuit has been set up for you. Carry out the following instructions, referring to Fig. 2.1. resistance wire A resistance wire B crocodile clip l A V Fig. 2.1 (a) Connect the crocodile clip to a length l = 90.0 cm of resistance wire A. Close the switch. Measure, and record in Table 2.1, the value of potential difference (p.d.) V and current I for the wire. Open the switch. Calculate, and record in Table 2.1, the resistance R of 90.0 cm of wire A. Use your values of V and I and the equation R = V I . [3] Table 2.1 wire l / cm V / I / R / A 90.0 B 90.0 A 50.0 B 50.0 (b) (i) Repeat step (a) for l = 90.0 cm of wire B, l = 50.0 cm of wire A and l = 50.0 cm of wire B. [2] (ii) Complete the headings in Table 2.1. [1] (c) (i) Calculate a value P using your results from Table 2.1 and the equation P = R for 90.0 cm of wire A R for 90.0 cm of wire B. P = … [1] (ii) Calculate a value Q using your results from Table 2.1 and the equation Q = R for 50.0 cm of wire A R for 50.0 cm of wire B. Q = … [1] (iii) A student suggests that the values of P and Q should be equal. State whether your results support this suggestion. Justify your answer by reference to values from your results. statement … justification… [2] (d) Suggest one reason why students all doing this experiment carefully with the same apparatus may not obtain the same results.… [1] [Total: 11]

2021 MarchPaper 5Question 3Component 52Variant 211 marks
Experimental skills and investigations
Loading original question

3 In this experiment, you will investigate a resistor and a lamp connected in series. The circuit has been set up for you with the voltmeter connected to measure the potential difference across the lamp. Carry out the following instructions, referring to Fig. 3.1. power supply resistance wire crocodile clip V A Fig. 3.1 (a) (i) Switch on. Move the crocodile clip on the resistance wire so that the value of the potential difference VL across the lamp is 2.0 V. Measure, and record in Table 3.1, the value of the current I for the lamp and resistor in series. Disconnect the voltmeter and re-connect it so that it measures the potential difference across the resistor. Measure, and record in Table 3.1, the value of the potential difference VR across the resistor. Switch off. Disconnect the voltmeter and re-connect it in its original position across the lamp. [1] (ii) Repeat the steps in (a)(i) for VL = 1.0 V and VL = 0.5 V. [2] Table 3.1 VL / V I / A VR / V RL / Ω RR / Ω 2.0 1.0 0.5 (b) Calculate, and record in Table 3.1, the resistance of the lamp RL for each value of VL. Use your values of VL and I from Table 3.1 and the equation RL = VL I . Calculate, and record in Table 3.1, the resistance of the resistor RR for each value of VL. Use your values of VR and I from Table 3.1 and the equation RR = VR I . [3] (c) A student suggests that RR should be constant. State whether your results support this suggestion. Justify your statement by reference to values from Table 3.1. statement… justification… [2] (d) A student wishes to determine the resistance of the lamp RL when the potential difference across the lamp VL = 0.0 V. Describe how the experiment can be extended to do this with the help of a suitable graph. You are not required to carry out this additional experiment.… [2] (e) It is possible to use a variable resistor instead of a resistance wire to change the potential difference across the lamp. Complete the circuit in Fig. 3.2 to show a variable resistor used for this purpose. You are not required to carry out this experiment. power supply V A Fig. 3.2 [1] [Total: 11]

2021 JunePaper 5Question 3Component 51Variant 111 marks
Experimental skills and investigations
Loading original question

3 In this experiment, you will investigate the refraction of light in the material of a transparent block. Carry out the following instructions, using the separate ray-trace sheet provided. You may refer to Fig. 3.1 for guidance. eye hole P N Q B A J F E K L H G C D i Fig. 3.1 (a) • Place the transparent block, largest face down, on the ray-trace sheet supplied. The block should be approximately in the middle of the paper. • Draw and label the outline of the block ABCD, as shown in Fig. 3.1. • Remove the block and draw a normal at the centre of side AB. Continue the normal so that it passes through side CD of the block. Label the normal NL. • Label the point Q where NL crosses AB. • Draw a line EF parallel to CD and 2.0 cm below CD. • Label the point J where NL crosses EF. • Draw a line GH parallel to CD and 7.0 cm below CD. • Label the point K where NL crosses GH. [2] (b) • Draw the line PQ at an angle i = 30° to the normal as shown in Fig. 3.1. • Place the paper on the pin board. • Place two pins, P1 and P2, on line PQ at a suitable distance apart for this experiment. • Replace the block and look from the position of the eye shown in Fig. 3.1 to observe the images of P1 and P2 through side CD of the block. Adjust your line of sight until the images of P1 and P2 appear one behind the other. • Place a pin P3 on line EF between your eye and the block so that the images of P1 and P2 seen through the block appear behind P3. • Place a pin P4 on line GH between your eye and the block so that P3, and the images of P1 and P2 seen through the block, appear behind P4. • Label the positions of P1, P2, P3 and P4. • Remove the pins. [2] (c) (i) Measure and record the length a of the line from J to P3. a = … [1] (ii) Measure and record the length b of the line from K to P4. b = … [1] (iii) Calculate b a . b a = … [2] (d) State one precaution that you took in order to produce an accurate ray trace.… [1] (e) A student plans to test the suggestion that, in this experiment, b a is a constant for all possible values of i. List suitable values of i that the student could use. … [2] Tie your ray-trace sheet into this booklet between pages 8 and 9. [Total: 11]

2021 JunePaper 5Question 3Component 52Variant 211 marks
Experimental skills and investigations
Loading original question

3 In this experiment, you will investigate resistance. Carry out the following instructions, referring to Fig. 3.1. A V power supply R l B C D resistance wire sliding contact S Fig. 3.1 (a) (i) Close the switch. Measure the current I in the circuit. I = … [1] (ii) Place the sliding contact S at C. Measure the potential difference (p.d.) VR across the resistor R. VR = … [1] Open the switch. (iii) Calculate the resistance R of the resistor using the equation R = VR I . R = … [2] (b) Disconnect the voltmeter from terminal B. Connect the voltmeter to terminal C. Close the switch. • Place the sliding contact S at a distance l = 20.0 cm from C. • Measure, and record in Table 3.1, the reading on the voltmeter. • Repeat the procedure using l = 40.0 cm, 60.0 cm, 80.0 cm and 100.0 cm. Open the switch. Table 3.1 l / cm V / V 20.0 40.0 60.0 80.0 100.0 [1] (c) Plot a graph of V / V (y-axis) against l / cm (x-axis). Start both axes at the origin (0,0). 0 0 [4] (d) Use your value of VR from (a)(ii) to find the length l R of resistance wire that has the same resistance as resistor R. Show clearly on the graph how you obtained the necessary information. l R = … cm [2] [Total: 11]

2021 JunePaper 5Question 3Component 53Variant 311 marks
Experimental skills and investigations
Loading original question

3 In this experiment, you will investigate the refraction of light by a transparent block. You will determine a quantity known as the refractive index of the material of the block. Carry out the following instructions, using the separate ray-trace sheet provided. You may refer to Fig. 3.1 for guidance. eye hole E N A D F C B ray-trace sheet θ 2 cm Fig. 3.1 (a) • Place the block approximately in the centre of the ray-trace sheet. Carefully draw round the block and label the corners ABCD as indicated by Fig. 3.1. • Remove the block from the ray-trace sheet. • Draw a normal to line AB at a point N, 2 cm from A. Extend the normal downwards until it crosses the line CD. Label the point at which it crosses CD with the letter F. • Draw a line NE, as indicated by Fig. 3.1, 8 cm long and at an angle θ1 = 20°. [1] (b) • Replace the block in exactly the same position as in (a). • Place two pins, P1 and P2, on line NE, a suitable distance apart for accurate ray tracing. • Label the positions of P1 and P2. • View the images of P1 and P2 through the block from the direction indicated by the eye in Fig. 3.1. Place two pins, P3 and P4, a suitable distance apart, so that pins P3 and P4, and the images of P1 and P2, all appear exactly one behind the other. • Label the positions of P3 and P4. • Remove the block and pins from the ray-trace sheet. • Draw a line joining P3 and P4. Extend this line until it meets NF. • Label the point at which this line meets NF with the letter G. Label the point at which this line crosses CD with the letter H. • Draw a line joining points N and H. [3] (c) Measure the length a of line NH. a = … cm Measure the length b of line GH. b = … cm Calculate a value n1 for the refractive index, using the equation n1= a b. n1 = … [2] (d) Draw a new line NE, as indicated by Fig. 3.1, 8 cm long and at an angle θ2 = 40°. Repeat the steps in (b). (i) Measure the length c of the new line NH. c = … cm Measure the length d of the new line GH. d = … cm Calculate a second value n2 for the refractive index, using the equation n2 = c d. n2 = … [1] (ii) State whether n1 or n2 is likely to be the more accurate value. Explain your answer. statement … explanation… [1] (e) (i) Measure the angle α, where α is the smaller angle between the line GH from (b) and the line GH from (d). α = … [1] (ii) A student suggests that the angle α should be equal to the difference between the angle θ2 from (d) and the angle θ1 from (a). State whether your results support this suggestion. Justify your answer by reference to your results. statement … justification… [1] (f) Suggest why different students, all carrying out this experiment carefully, may not obtain identical results.… [1] Tie your ray-trace sheet into this booklet between pages 10 and 11. [Total: 11]

2021 NovemberPaper 5Question 3Component 51Variant 111 marks
Experimental skills and investigations
Loading original question

3 In this experiment you will investigate the position of the image in a plane mirror. Carry out the following instructions. Use the ray-trace sheet supplied, referring to Fig. 3.1 for guidance. hole M R N L A C B eye Fig. 3.1 (a) • Draw a line 10 cm long near the middle of the ray-trace sheet. Label the line MR. Draw a normal to this line that passes through its centre. Label the normal NL. Label the point at which NL crosses MR with the letter B. • Draw a line 7.0 cm long from B at an angle of incidence i = 70° to the normal below MR and to the left of the normal. Label the end of this line A. • Draw another line 7.0 cm long from B at an angle θ = 40° to the normal below MR and to the left of the normal. Label the end of this line C. [2] (b) • Place the reflecting face of the mirror vertically on the line MR. • Place two pins, P1 and P2, on line AB at a suitable distance apart for this type of ray-trace experiment. Label the positions of P1 and P2. • View the images of pins P1 and P2 from the direction indicated by the eye in Fig. 3.1. Place two pins, P3 and P4, so that pins P3 and P4 and the images of P2 and P1 all appear exactly one behind the other. Label the positions of P3 and P4. [2] (c) Remove the pins and the mirror. Draw a line through the positions of P3 and P4. Continue the line until it meets MR. Measure the angle α between the line and the normal NL below MR. α = … [1] (d) Place the reflecting face of the mirror vertically on the line AB with the centre of the mirror at B. Place pins P1 and P2 on line CB at a suitable distance apart for this type of ray-trace experiment. View the images of pins P1 and P2. Place pins P3 and P4 so that pins P3 and P4 and the images of P2 and P1 all appear exactly one behind the other. Label the new positions of P3 and P4. [1] (e) Remove the pins and the mirror. Draw a line through the new positions of P3 and P4. Continue the line until it meets NL. Measure the angle β between the line and NL below MR. β = … [2] (f) A student investigates a possible relationship between angles α and β. The angle θ remains constant at θ = 40°. Suggest values of the angle of incidence i that he could use.… [2] (g) A student does this experiment with care. Suggest one practical reason why the results may not be exactly those that the theory of reflection predicts.… [1] Tie your ray-trace sheet into this booklet between pages 8 and 9. [Total: 11]

2021 NovemberPaper 5Question 3Component 52Variant 211 marks
Experimental skills and investigations
Loading original question

3 In this experiment, you will investigate the image produced by a lens. Carry out the following instructions, referring to Fig. 3.1. illuminated object u v lens screen bench Fig. 3.1 (a) • Place the lens a distance u = 20.0 cm from the illuminated object. • Move the screen until a clearly focused image is formed on the screen. • Measure the distance v between the centre of the lens and the screen. (i) Record v in Table 3.1. [1] (ii) Calculate, and record in Table 3.1, u v . [1] (iii) Repeat the procedure for u = 25.0 cm, u = 30.0 cm, u = 35.0 cm and u = 40.0 cm. [1] Table 3.1 u / cm v / cm u v 20.0 25.0 30.0 35.0 40.0 (b) Plot a graph of u / cm (y-axis) against u v (x-axis). Start the y-axis at u = 15.0 cm. [4] (c) Use your graph to find the value of u when u v = 1.0. Show clearly on the graph how you obtained the necessary information. u = … [2] (d) Suggest one practical difficulty with this experiment. Explain briefly how you would try to overcome this difficulty in order to obtain accurate results. suggestion… explanation… [2] [Total: 11]

Full Paper 5 past papers with mark schemes

Paper 5: quick facts

Which topics come up most in IGCSE Physics 0625 Paper 5?

The most-tagged topics in IGCSE Physics 0625 Paper 5 are Experimental skills and investigations (212), Electricity and magnetism (26) and Waves (21), out of 212 past-paper questions from 2019-2026. These are archive counts, not a prediction, and a question can carry more than one topic.

Are the IGCSE Physics 0625 Paper 5 questions free?

84 of the 212 IGCSE Physics 0625 Paper 5 questions are free to practise. The other 128 need a plan for IGCSE Physics 0625, from $6 a month.

Do the IGCSE Physics 0625 Paper 5 questions have answers?

Yes. Each IGCSE Physics 0625 Paper 5 question shows the official mark scheme answer. Many also have a step-by-step worked explanation written by PastPaperPrep.