1.12 · AHL · HL onlyPaper 1Paper 2

Torque and rotational equilibrium

In a minute

A can turn a body as well as push it. Its turning effect about an axis is its , τ=Frsin⁡θ\tau = Fr\sin\theta. When the torques on a body cancel, it is in ; when they don't, its rotation speeds up or slows down.

You'll be able to

  • Calculate a force's torque about an axis with τ=Frsin⁡θ\tau = Fr\sin\theta, and give its sense: clockwise or anticlockwise.
  • Find the perpendicular distance from an axis to a force's line of action.
  • Use zero resultant torque to find unknown forces and distances in balanced bodies.
  • Treat the weight of a uniform body as acting at its .
  • Explain why an unbalanced torque gives a rigid body an angular acceleration.
Before you start3 quick questions on what this builds on
Check yourself
Two horizontal forces act on a crate: 45 N\pu{45 N} to the right and 28 N\pu{28 N} to the left. What is the size of the , in N?
Check yourself
A book rests on a table. Which forces belong on the book's ?
Check yourself
Where is the centre of mass of a uniform straight rod?

Revise first: 1.4 Newton's laws and free-body diagrams and 4.1 Gravitation: Kepler's laws and Newton's law

Torque

Push a door near its handle and it swings open easily. Push with the same force near the hinges and it barely moves. Push along the door, straight towards the hinges, and nothing turns at all.

So the turning effect depends on three things: the size of the force, how far from the axis it acts, and its direction. Torque combines all three.

In the formula booklet
τ=Frsin⁡θ\tau = Fr\sin\theta

This equation is in section A.4 of the data booklet. τ\tau is the Greek letter tau.

Another way to read it: rsin⁡θr\sin\theta is the perpendicular distance from the axis to the force's line of action. The line of action is the force arrow extended both ways. So torque = force × perpendicular distance, as the figure shows.

A spanner pivots about a bolt at O on the left. The spanner runs horizontally to the right, a length r, to point P where a force F is applied. F points up and to the right, at angle theta to the line from O through P. A dashed line extends the force's line of action back below P. A short solid line from O meets this dashed line at a right angle; it is labelled r sin theta, the perpendicular distance. A curved arrow round O shows the force turns the spanner anticlockwise. O axis (bolt) r P F θ line of action of F r sin θ anticlockwise
The torque is FF times the perpendicular distance rsin⁡θr\sin\theta from the axis to the line of action.

The torque is largest when the force is at 90∘90^{\circ} to the line from the axis (sin⁡90∘=1\sin 90^{\circ} = 1). It is zero when the line of action passes through the axis (θ=0∘\theta = 0^{\circ} or 180∘180^{\circ}).

Torque also has a sense: it turns the body clockwise or anticlockwise, seen from one side. You don't need torque's vector direction, but always state the sense.

Worked exampleA mechanic pulls on a spanner with a force of 65 N\pu{65 N}, applied 0.28 m\pu{0.28 m} from the centre of the bolt. The force acts at 70∘70^{\circ} to the spanner. Calculate the torque about the bolt.

Try it first, then reveal one step at a time.

  1. Identify the quantities: F=65 NF = \pu{65 N}, r=0.28 mr = \pu{0.28 m}, θ=70∘\theta = 70^{\circ}, the angle between the force and the spanner.
Worked exampleA cyclist pushes vertically down with a force of 520 N\pu{520 N} on a pedal. The crank, from the axle to the pedal, is 0.17 m\pu{0.17 m} long and points forwards at 30∘30^{\circ} above the horizontal. The bicycle is seen from its right side, facing right. Determine the torque about the axle and its sense.

Try it first, then reveal one step at a time.

  1. The crank is 30∘30^{\circ} above the horizontal and the force is vertical, so the angle between them is θ=90∘+30∘=120∘\theta = 90^{\circ} + 30^{\circ} = 120^{\circ}.

When the crank points straight down, the downward push acts along it, through the axle. The torque is then zero, however hard the cyclist pushes.

Check yourself
A force acts on a door that turns about its hinges. In which case is the torque about the hinges zero?
Check yourself
A force of 12 N\pu{12 N} acts on the end of a bar 0.45 m\pu{0.45 m} long, at 35∘35^{\circ} to the bar. The bar can turn about its other end. Calculate the torque, in N m. Give 2 significant figures.

Rotational equilibrium

A seesaw with two children on it can balance, even if one child is heavier. The heavier child just sits nearer the pivot. Each child's has a torque about the pivot, and the two torques are equal and opposite.

Zero resultant torque does not mean the body is still. It means its rotation doesn't change: it stays at rest, or keeps turning at a steady rate.

For an extended body, take its whole weight as acting at its . For a uniform beam, that is its midpoint. You never need to calculate where the centre of mass is; it will be given or obvious.

A body that stays at rest is in full equilibrium. It needs zero and zero resultant torque. Then the torques balance about every axis, so you can choose any point to take torques about.

Worked exampleA uniform seesaw is pivoted at its centre. A child of mass 28 kg\pu{28 kg} sits 1.6 m\pu{1.6 m} from the pivot. Where must a child of mass 35 kg\pu{35 kg} sit, on the other side, so that the seesaw balances horizontally?

Try it first, then reveal one step at a time.

  1. The seesaw's own weight acts at its centre, through the pivot, so it has no torque about the pivot.
A uniform shelf 1.40 m long rests on a bracket at each end, A on the left and B on the right. A box sits on the shelf 0.30 m from end A. Four forces act on the shelf: an upward force F A at end A, a shorter upward force F B at end B, the push of the box, 5.0 g, downward at 0.30 m from A, and the weight of the shelf, 3.0 g, downward at its midpoint, 0.70 m from A, labelled centre of mass. A B box FA FB box: 5.0g shelf: 3.0g centre of mass 0.30 m 0.70 m 1.40 m
The four forces on the shelf. Its own weight acts at its centre of mass.
Worked exampleA uniform shelf of mass 3.0 kg\pu{3.0 kg} and length 1.40 m\pu{1.40 m} rests on brackets A and B at its ends, as in the figure. A box of mass 5.0 kg\pu{5.0 kg} sits 0.30 m\pu{0.30 m} from end A. Determine the upward force from bracket A.

Try it first, then reveal one step at a time.

  1. Take torques about B, so the unknown FBF_\text{B} drops out. All the forces are vertical and the shelf horizontal, so each torque is force × distance from B. Use g=9.8 m s−2g = \pu{9.8 m s-2} from the data booklet.
Check yourself
A uniform metre rule of mass 0.12 kg\pu{0.12 kg} balances on a pivot at its 40.0 cm mark, with a small mass hung at the 10.0 cm mark. Calculate the hung mass, in grams. Give 2 significant figures.
Check yourself
A ladder leans at rest against a wall. Which statement must be true?

Unbalanced torque

If the torques on a rigid body don't cancel, the body is not in rotational equilibrium. Its rotation changes: it gains an .

Angular acceleration is the rate at which the rotation speeds up or slows down. If the resultant torque opposes the way the body is turning, the rotation slows. 1.13 makes this quantitative with τ=Iα\tau = I\alpha.

Turning a steering wheel with two hands, you push up on one side and pull down on the other with equal forces. The resultant force is zero, so the wheel's centre stays put. But both forces turn the wheel the same way, so the resultant torque is not zero.

A steering wheel seen face-on, turning about its centre. A hand on the right of the rim pushes up with force F. A hand on the left of the rim pulls down with an equal force F. The two forces are parallel and opposite, and their lines of action are a distance d apart, the diameter of the wheel. A curved arrow at the centre shows the wheel turning anticlockwise. Notes beside the wheel read: resultant force zero, resultant torque F d, anticlockwise. F F d resultant force = 0 resultant torque = Fd, anticlockwise
Equal, opposite, parallel forces (a couple): zero resultant force, but a resultant torque FdFd.

So zero resultant force does not stop a body rotating faster. Equally, a force whose line of action passes through the centre of mass can accelerate a free body without making it spin.

Worked exampleA uniform rod is pivoted at its left end and held horizontal. It is then released. Explain why the rod starts to rotate about the pivot.

Try it first, then reveal one step at a time.

  1. List the forces on the rod: its weight and the force from the pivot.
Worked exampleA drum of radius 0.25 m\pu{0.25 m} turns anticlockwise on a fixed axle. A rope wound round it pulls tangentially with 30 N\pu{30 N}, turning it anticlockwise. A brake pad rubs on a rim of radius 0.30 m\pu{0.30 m}, with a tangential friction force of 18 N\pu{18 N} opposing the motion. Determine the resultant torque on the drum, and state what happens to its rotation.

Try it first, then reveal one step at a time.

  1. Take anticlockwise as positive. Both forces are tangential, so each is at 90∘90^{\circ} to its radius and sin⁡θ=1\sin\theta = 1.
Check yourself
The resultant force on a rigid body is zero. What can you conclude about its rotation?
Check yourself
A driver pushes up on one side of a steering wheel and pulls down on the other, each with a tangential force of 24 N\pu{24 N}. The wheel's diameter is 0.38 m\pu{0.38 m}. Calculate the resultant torque about the centre, in N m. Give 2 significant figures.

Common mistakes

  • Multiplying the force by the distance to where it acts, ignoring the angle. Use rsin⁡θr\sin\theta, the perpendicular distance from the axis to the line of action.
  • Forgetting the weight of the beam itself. For a uniform beam it acts at the midpoint, its centre of mass.
  • Adding clockwise and anticlockwise torques together. Choose a positive sense and subtract the other way.
  • Saying a body is in equilibrium because the forces balance. A couple has zero resultant force but still turns the body.
  • Thinking zero resultant torque means no rotation. It means no angular acceleration: a wheel can keep spinning steadily.

Exam tips

  • "State" the condition for rotational equilibrium: the resultant torque on the body is zero. Saying only that the forces balance earns nothing.
  • In "determine" questions with two unknown support forces, take torques about one support to find the force at the other, then use force balance for the first. Write the torque equation, substitute, then give the answer in N.
  • Give torques in N m with their sense. Show τ=Frsin⁡θ\tau = Fr\sin\theta and the angle you used.
  • In Paper 1A, check the angle first: the torque is largest when the force is at 90∘90^{\circ} to the line from the axis, and zero when its line of action passes through the axis.

Key takeaways

In bookletτ=Frsin⁡θ\tau = Fr\sin\theta
Learn thisrsin⁡θr\sin\theta is the perpendicular distance from the axis to the line of action. Torque is in N m; always give its sense, clockwise or anticlockwise.
Learn thisRotational equilibrium: resultant torque zero, so clockwise torques = anticlockwise torques. A body at rest also needs zero resultant force.
Learn thisTake the weight of an extended body as acting at its centre of mass: the midpoint of a uniform beam.
Learn thisAn unbalanced torque gives a rigid body an angular acceleration in the sense of the resultant torque. A force through the axis has no torque.

Practise this

42 past-paper questions on Rigid body and rotational mechanics in the Physics HL bank, each with a mark scheme and a worked explanation.

Practise Rigid body and rotational mechanics →