Particles, density and temperature
In a minute
Matter is made of tiny particles that are always moving. How closely they pack and how freely they move explains the differences between a solid, a liquid and a , and sets each substance's . , on the Celsius or , measures the average of those particles.
You'll be able to
- Describe solids, liquids and gases in terms of how their particles are arranged, how they move and the forces between them, and name the phase changes.
- Calculate density with , and rearrange it to find a mass or a volume, in SI units.
- Convert temperatures between degrees Celsius and kelvin.
- Explain why a temperature change has the same value in kelvin and in degrees Celsius, and when you must use kelvin.
- Use to link the kelvin temperature to the average kinetic energy of the particles.
Before you start3 quick questions on what this builds on
Revise first: 6.2 Scalars and vectors and 6.4 Graphs and data analysis
Solids, liquids and gases
Everything around you is made of particles: atoms or molecules, far too small to see. A simple model of how they are arranged and how they move explains much of what you can see.
The model has two ideas. The particles are always moving. They attract each other when they are close, and repel strongly if pushed even closer. Far apart, the forces between them are tiny.
In a solid, the particles are packed close together in fixed positions, often in a regular pattern. Strong forces hold each one in place, so it can only vibrate about that position. A solid keeps its own shape and volume.
In a liquid, the particles are still close together, so a liquid keeps its volume and is very hard to compress. They are not held in fixed positions, so they can slide past one another. A liquid flows and takes the shape of its container.
In a , the forces between particles are negligible except during collisions. Each particle moves in a straight line until it hits another particle or the wall. Most of a gas is empty space, so it is easy to compress.
Changes between phases have names you should know. Melting is solid to liquid and freezing is liquid to solid. Condensing is gas to liquid. Boiling and evaporation are both liquid to gas, but they differ.
Boiling happens throughout the liquid and, for a pure liquid, at one temperature for a given pressure: the boiling point. Evaporation happens only at the surface, at any temperature. The particles in a liquid have a range of speeds, and the fastest ones near the surface can escape. You will see what happens to the energy during these changes in 2.2.
Try it first, then reveal one step at a time.
- Compare how far apart the particles are in each phase.
- Say what pushing the plunger does to that spacing, and what stops it in the liquid.
- In air, a gas, the particles are far apart compared with their size, so most of the volume is empty space. Pushing the plunger moves the particles closer together, so the volume of the air decreases. In water, a liquid, the particles are already close together. Moving them any closer needs very large forces, because the particles repel strongly when squeezed together. So the volume of the water hardly changes.
Try it first, then reveal one step at a time.
- Start from the fact that the particles do not all move at the same speed.
- Say which particles leave, and from where.
- Finish with one clear difference from boiling.
- The water particles have a range of speeds, so a range of kinetic energies. Some of the fastest particles near the surface have enough energy to escape the attraction of their neighbours. They leave the surface and become a gas, so evaporation happens at any temperature. Evaporation happens only at the surface, while boiling happens throughout the liquid at the boiling point.
Density
A suitcase of feathers and a small block of lead can have the same mass. The lead is tiny because far more mass is packed into each cubic metre of it.
is given by this equation, which is in the data booklet.
(the Greek letter rho) is the density, is the mass in kg and is the volume in . The SI unit of density is . Density is a : it has a size but no direction.
Density is a property of the material, not of the object. Cut a steel bar in half and each half has half the mass and half the volume, so the same density.
The particle model explains the numbers. Solids and liquids have similar densities, because their particles are close together in both. At everyday pressures, a gas is roughly a thousand times less dense than its liquid, because its particles are far apart. Water is about ; air is about .
Lab data often come in grams and . Since and , a density of is .
Try it first, then reveal one step at a time.
- Find the volume: .
- Convert the mass: .
- Substitute into : .
- The lengths have 2 significant figures, so give 2.
Try it first, then reveal one step at a time.
- Convert the radius: .
- Volume of a cylinder: .
- Rearrange to .
- Substitute: . Give 2 significant figures, like the data.
Celsius and kelvin
The Celsius scale was built around water: ice melts at and water boils at , at normal atmospheric pressure. It is handy for weather and cooking, but its zero is just a convenient choice.
Cool anything down and its particles move more and more slowly. There is a lowest possible temperature, called absolute zero, at about . Nothing can be colder.
To convert, add 273. This conversion is printed in the data booklet's unit conversions:
Here (theta) is a Celsius temperature and is the absolute temperature on the . The unit is written K, with no degree sign: , not . A kelvin temperature is never negative.
Because one kelvin is the same size as one degree Celsius, a temperature change has the same number on both scales. Warming from to is a rise of . In kelvin it is to , a rise of .
The algebra shows why: . The 273s cancel. So for a change you may use either scale, but a temperature that is multiplied, divided or put in a ratio must be in kelvin.
Try it first, then reveal one step at a time.
- Use , keeping the minus sign: .
- Check: the answer is positive and well below , the melting point of ice, as it should be.
Try it first, then reveal one step at a time.
- The two readings are on different scales, so first put both on one scale. Convert the start: .
- Subtract: .
- Check on the Celsius scale: , and . The change is the same number on both scales.
Temperature and particle kinetic energy
The particles in a hot cup of tea move faster, on average, than those in a glass of cold water. Temperature is a way of measuring this motion.
The word random matters. A ball thrown across a room has extra as a whole, but that ordered motion does not make it any hotter. Only the jiggling of the particles relative to each other counts.
For a gas, the kelvin and the average kinetic energy of one particle are linked by this data booklet equation.
Here is the average kinetic energy of one particle, in J, from its random motion from place to place. must be in kelvin. The is in the data booklet's list of constants. It is per particle, so it is tiny; don't confuse it with the gas constant , which is per mole and which you meet in 2.8.
and are in . Double the kelvin temperature and the average kinetic energy doubles. In this model the average kinetic energy is zero at , which is why absolute zero is the bottom of the scale.
The equation does not contain the particle's mass. So at the same temperature, every kind of gas particle has the same average kinetic energy. Since , lighter particles, such as helium atoms, move faster on average than heavier ones.
is an average. At any moment some particles move much faster and some much slower. That spread is what lets the fastest particles escape in evaporation.
Try it first, then reveal one step at a time.
- Convert to kelvin: .
- Substitute into with from the data booklet: .
- The temperature has 2 significant figures, so give 2.
Try it first, then reveal one step at a time.
- only for in kelvin. Convert: and .
- Divide the two equations so cancels: .
- Comment: the student doubled the Celsius value, which is not proportional to the energy. The average kinetic energy rises by only about 5%.
Common mistakes
- Using degrees Celsius in or in any ratio of temperatures. Convert to kelvin first by adding 273.
- Adding 273 to a temperature change. A change of is a change of .
- Writing the unit as . The kelvin has no degree sign: write .
- Turning into by dividing by 100. Divide by , then the density comes out in .
- Saying temperature measures "the energy" or the total kinetic energy of the particles. It measures their average random kinetic energy.
- Saying particles in a solid are still. They vibrate about fixed positions.
Exam tips
- "Describe" or "explain" a difference between phases: compare the spacing of the particles, how they move and the forces between them. Name the phase in each sentence and give one point per sentence.
- "Calculate" a density: convert to kg and , write , substitute, then give the answer in to the significant figures of the least precise datum.
- In Paper 1A ratio questions, convert every temperature to kelvin before any multiplying or dividing; a temperature difference can stay in .
- "State what is meant by" temperature: say it is a measure of the average random kinetic energy of the particles. "Energy" on its own is too vague.
Key takeaways
Practise this
86 past-paper questions on Thermal concepts and energy transfer in the Physics HL bank, each with a mark scheme and a worked explanation.