5.11 · SLPaper 1Paper 2

Fission and nuclear power

In a minute

In , a heavy nucleus splits into two medium-mass nuclei that are more tightly bound, so energy is released. The neutrons it gives off can split more nuclei in a . A nuclear power plant keeps that chain steady, turns the energy into electricity, and must then store radioactive waste for thousands of years.

You'll be able to

  • Describe spontaneous and neutron-induced fission, and calculate the energy released from masses or from .
  • Explain how a chain reaction works, and when its rate stays steady, grows or dies out.
  • Explain the roles of the , , and , and calculate how much fuel a power station uses.
  • Describe the properties of fission products, how nuclear waste is managed, and the impact of storing it for a very long time.
Before you start3 quick questions on what this builds on
Check yourself
A heavy nucleus splits into two medium-mass nuclei, and energy is released. How does the binding energy per nucleon of the products compare with that of the heavy nucleus?
Check yourself
Two trolleys at rest are pushed apart by a spring in an . Trolley P has three times the mass of trolley Q. Which statement is correct?
Check yourself
A power station takes in energy at a rate of 3.0 GW\pu{3.0 GW} and delivers electrical power of 1.1 GW\pu{1.1 GW}. Calculate its as a decimal, to 2 significant figures.

Revise first: 1.7 Collisions and explosions, 1.11 Power, efficiency and energy density and 5.6 Binding energy and mass defect

Energy from fission

In 5.6 you saw that binding energy per nucleon peaks near iron and falls slowly for heavier nuclei. So when a very heavy nucleus splits into two medium-mass nuclei, the products are more tightly bound, and energy is released.

Fission happens in two ways. In spontaneous fission, a nucleus splits on its own, at random, with nothing hitting it. Californium-252 does this; uranium-238 does too, but very rarely.

In neutron-induced fission, a nucleus first absorbs a neutron. Uranium-235, the used in most reactors, absorbs a slow neutron and becomes uranium-236, which is unstable and usually splits almost at once.

A slow neutron travels right towards a uranium-235 nucleus. The nucleus absorbs it and becomes an unstable, stretched uranium-236 nucleus. This splits into two medium-mass fission fragments that fly apart, one up and to the right and one down and to the right, together with two fast neutrons moving to the right. slow neutron uranium-235 uranium-236, unstable fragment fragment fast neutrons
Neutron-induced fission of uranium-235. The two fragments and the new neutrons all fly off at high speed.

A typical equation is 01n+92235U→56144Ba+3689Kr+3 01n^{1}_{0}\text{n} + {}^{235}_{92}\text{U} \rightarrow {}^{144}_{56}\text{Ba} + {}^{89}_{36}\text{Kr} + 3\,{}^{1}_{0}\text{n}. Nucleon number and proton number are both conserved.

The two positive fragments repel and fly apart like an . About 80% of the energy appears as their . The rest goes to the neutrons, gamma photons and the later decay of the fragments.

The uranium-236 nucleus is almost at rest and no external force acts, so momentum is conserved: ignoring the neutrons, the fragments have equal and opposite momenta. Since Ek=p22mE_\text{k} = \frac{p^{2}}{2m}, the lighter fragment gets more of the kinetic energy.

By , the products have less mass than the reactants. You can find the energy released in two ways.

In the formula booklet
E=mc2E = mc^{2}

1. From masses: find the mass lost, Δm\Delta m, then E=Δm c2E = \Delta m\, c^{2}. With masses in u, multiply Δm\Delta m by 931.5 to get MeV.

2. From : subtract the total binding energy of the reactants from that of the products. Free neutrons have none.

Learn this
Ereleased=Δm c2=EB, products−EB, reactantsE_\text{released} = \Delta m\, c^{2} = E_\text{B, products} - E_\text{B, reactants}
Worked exampleA uranium-235 nucleus absorbs a neutron and splits: 01n+92235U→55137Cs+3797Rb+2 01n^{1}_{0}\text{n} + {}^{235}_{92}\text{U} \rightarrow {}^{137}_{55}\text{Cs} + {}^{97}_{37}\text{Rb} + 2\,{}^{1}_{0}\text{n}. The atomic masses are uranium-235: 235.043930 u, caesium-137: 136.907089 u, rubidium-97: 96.937340 u. Determine the energy released in one fission, in MeV.

Try it first, then reveal one step at a time.

  1. These are masses of atoms, but both sides have 92 electrons, so the electron masses cancel.
Worked exampleCalifornium-252 can split with nothing hitting it, while uranium-235 splits after absorbing a neutron. Outline the difference between these two kinds of fission, and state the form in which most of the released energy first appears.

Try it first, then reveal one step at a time.

  1. Name each kind of fission and say what starts it.
Check yourself
A uranium-235 nucleus absorbs one neutron and splits into lanthanum-147 and bromine-87, plus some neutrons. How many neutrons are released?
Check yourself
A uranium-235 nucleus absorbs a neutron and splits into cerium-146, selenium-88 and two neutrons. The binding energies per nucleon are uranium-235: 7.6 MeV\pu{7.6 MeV}, cerium-146: 8.30 MeV\pu{8.30 MeV}, selenium-88: 8.55 MeV\pu{8.55 MeV}. Calculate the energy released, in MeV, to 2 significant figures.
Check yourself
A uranium-236 nucleus at rest splits into two fragments of nucleon numbers 146 and 88. Ignore the neutrons. The fragments share 165 MeV\pu{165 MeV} of kinetic energy. Calculate the kinetic energy of the lighter fragment, in MeV, to 3 significant figures.

Chain reactions

Each fission of uranium-235 usually releases 2 or 3 neutrons. Each can be absorbed by another uranium-235 nucleus and cause another fission, which releases more neutrons.

Some neutrons escape from the fuel, and some are absorbed by nuclei that don't split, such as uranium-238. What matters is how many neutrons per fission, on average, cause another fission.

1. Fewer than one on average: each generation has fewer fissions, and the dies out.

2. Exactly one on average: the rate of fission stays constant. This is what a reactor needs for a steady power output.

3. More than one on average: the number of fissions grows every generation, extremely fast. An uncontrolled chain like this is what happens in a nuclear weapon.

Two chain reactions side by side. Left, labelled steady: a row of four fissions, each linked to the next by one neutron. From every fission one more neutron goes up and stops at a bar labelled absorbed, so the number of fissions stays at one per generation. Right, labelled growing: one fission sends neutrons to two fissions, those send neutrons to four, and those send neutrons on to eight. The columns are labelled 1, 2, 4 and 8 fissions. Steady: one neutron per fission causes another Growing: two neutrons per fission cause more fissions absorbed 1111 fissions per generation 1 2 4 8
Left: exactly one neutron per fission causes another, so the rate is steady. Right: two per fission do, so the number of fissions doubles each generation.
Worked exampleIn a reactor, each fission releases 2.4 neutrons on average. Of these, 0.6 are absorbed by uranium-238 without causing fission, 0.5 are absorbed by the control rods and 0.2 escape from the core. Determine the average number of neutrons per fission that cause a further fission, and state what happens to the rate of fission.

Try it first, then reveal one step at a time.

  1. Each neutron causes a fission, is absorbed without fission, or escapes. Subtract the losses: 2.4−0.6−0.5−0.2=1.12.4 - 0.6 - 0.5 - 0.2 = 1.1.
Worked exampleExplain what is meant by a chain reaction in nuclear fission, and state the condition for the rate of fission to stay constant.

Try it first, then reveal one step at a time.

  1. Say where the neutrons come from and what they do next.
Check yourself
In a sample of uranium, on average 1.4 neutrons from each fission cause another fission. What happens to the rate of fission?
Check yourself
Generation 1 of a chain is a single fission. Every fission causes exactly two fissions in the next generation. How many fissions happen in generation 10?

Inside a nuclear power plant

A power plant runs the chain reaction at a steady rate. The energy heats the core, and a steam turbine turns it into electricity. Four parts keep this controlled and safe.

Simplified nuclear power plant. On the left, the reactor core sits inside a thick wall of shielding. In the core, vertical fuel rods stand in moderator water, and control rods hang down between them from above and can be raised or lowered. Hot coolant leaves the top of the core through a pipe to a heat exchanger, and cooled coolant returns along a lower pipe. In the heat exchanger, energy passes through a coil to water in a separate circuit, which turns to steam. The steam drives a turbine, which turns a generator, and the water returns to the heat exchanger. G control rods fuel rods moderator (water) shielding raise or lower hot coolant cooled coolant heat exchanger steam turbine generator water
The coolant circuit carries energy from the core to the . The steam circuit is kept separate.

Moderator: fission releases fast neutrons, of about 2 MeV, but uranium-235 is far more likely to absorb slow ones, of about 0.03 eV. The slows the neutrons down.

It works by collisions with light nuclei, such as hydrogen in water or carbon in graphite. Each collision takes a significant share of the neutron's kinetic energy. Off a heavy nucleus, the neutron would bounce back with almost all of it.

Control rods: of boron or cadmium absorb neutrons. Lowering them reduces the rate of fission; raising them increases it. Operators set them so that, on average, exactly one neutron per fission causes another fission.

Heat exchanger: a coolant carries thermal energy from the core to the heat exchanger. There it boils water in a separate circuit, and the steam drives the turbine. The coolant, which can be radioactive, never reaches the turbine.

Shielding: thick steel and concrete absorbs the neutrons and gamma radiation from the core, protecting workers.

Worked exampleA nuclear power station has an electrical output of 750 MW\pu{750 MW} and an overall efficiency of 32%. Each fission of uranium-235 releases 205 MeV\pu{205 MeV}. Take the mass of one uranium-235 atom as 235 u. Determine the mass of uranium-235 that undergoes fission in one day.

Try it first, then reveal one step at a time.

  1. Power from fission: P=750×1060.32=2.344⋅109 WP = \frac{750 \times 10^{6}}{0.32} = \pu{2.344e9 W}.
Worked exampleExplain how the moderator and the control rods together allow a reactor to produce a steady power output.

Try it first, then reveal one step at a time.

  1. Give each part its own job, in terms of what it does to the neutrons.
Check yourself
The operators lower the control rods further into the core. What happens?
Check yourself
Each fission of uranium-235 releases 200 MeV\pu{200 MeV}. Taking the mass of one uranium-235 atom as 235 u, calculate the energy released per kilogram of uranium-235 that undergoes fission. Give your answer in J kg−1\text{J kg}^{-1}, to 2 significant figures.

Fission products and nuclear waste

Uranium-235 has about 1.55 neutrons per proton; stable medium-mass nuclei have fewer, about 1.25 to 1.45. The fragments keep the uranium's high share of neutrons, so they are unstable. This gives fission products three properties:

1. They are radioactive, mostly by , often with gamma rays.

2. Their range from fractions of a second to millions of years. Strontium-90 and caesium-137, about 30 years each, give most of the fission products' heat and radiation from a few years after removal until a few centuries later. A few, such as technetium-99, last hundreds of thousands of years.

3. Their decay releases energy, so spent fuel stays hot for years.

Spent fuel also holds plutonium-239, made when uranium-238 absorbs neutrons. It has a half-life of about 24 000 years.

Management: spent fuel first sits in deep pools of water for years, which carry away the heat and absorb radiation. It then goes into sealed steel and concrete casks. The long-term plan in several countries is a deep store in stable rock.

Long-term storage is the hard part. Some waste must stay isolated for tens of thousands of years. Stores must keep water out, survive earthquakes and stay secure, and future generations inherit the risk.

For climate change, a fission plant emits almost no carbon dioxide while running and gives steady power. Against that are the waste, the risk of accidents such as Chernobyl, and the high cost of building plants.

Worked exampleStrontium-90 has a half-life of 29 years. A container of waste holds strontium-90 with an activity of 6.4⋅1015 Bq\pu{6.4e15 Bq}. Calculate the activity of the strontium-90 after 145 years.

Try it first, then reveal one step at a time.

  1. Count the half-lives: 14529=5\frac{145}{29} = 5, so the activity halves 5 times: a factor of 25=322^{5} = 32.
Worked exampleExplain why the products of fission are radioactive, and why spent fuel is kept in pools of water for several years after it is removed from a reactor.

Try it first, then reveal one step at a time.

  1. Compare the neutrons per proton of uranium with that of stable medium-mass nuclei.
Check yourself
Why is spent fuel first stored in deep pools of water?
Check yourself
Plutonium-239 has a half-life of 2.4×1042.4 \times 10^{4} years. How many years does it take for the activity of a sample to fall to 116\tfrac{1}{16} of its starting value?

Common mistakes

  • Saying the moderator absorbs neutrons. It slows them, making fission more likely; the control rods absorb them.
  • Saying the control rods cool the reactor. The coolant and heat exchanger carry the energy away.
  • Forgetting the absorbed neutron, or the neutrons released, when balancing an equation or finding the mass lost.
  • Thinking that storing or cooling waste shortens its half-life. Nothing external changes a nuclide's half-life.

Exam tips

  • "Determine" the energy released: mass before minus mass after, with every neutron, times 931.5 for MeV.
  • In 1A, match each part to its one job: moderator slows neutrons, control rods absorb them, heat exchanger transfers energy, shielding absorbs radiation.
  • "Explain" a chain reaction: neutrons from one fission cause further fissions; steady means exactly one per fission on average.

Key takeaways

Learn thisFission: a heavy nucleus splits into two medium-mass nuclei and usually 2 or 3 neutrons, spontaneously or after absorbing a neutron.
Learn thisEreleased=Δm c2=EB, products−EB, reactants,1 u→931.5 MeVE_\text{released} = \Delta m\, c^{2} = E_\text{B, products} - E_\text{B, reactants}, \qquad \pu{1 u} \to 931.5\ \text{MeV}
Learn thisMost of the energy released first appears as kinetic energy of the fission fragments.
Learn thisChain reaction: steady when, on average, exactly one neutron per fission causes another fission; it grows above one and dies out below one.
Learn thisModerator slows neutrons; control rods absorb neutrons; heat exchanger passes energy to the steam circuit; shielding absorbs radiation.
Learn thisFission products are neutron-rich: radioactive (beta-minus, gamma), hot, some long-lived. Waste is cooled in water, sealed and stored deep underground.

Practise this

34 past-paper questions on Nuclear energy, fission and fusion in the Physics HL bank, each with a mark scheme and a worked explanation.

Practise Nuclear energy, fission and fusion →