Radians, arc length and sector area
In a minute
A measures an angle by the it cuts off: an angle of one radian has an arc exactly as long as the radius. With the angle in radians, the arc and the of 3.4 have short formulas, and . The trigonometric models of 2.9 use radians too.
You'll be able to
- Explain what one is, and why a full turn is radians.
- Convert angles between degrees and radians, giving radians as an exact multiple of or as a decimal.
- Find the arc length, perimeter and area of a with the angle in radians, including a major sector.
- Work backwards from an arc or an area to the radius or the angle, using your GDC where it helps, and interpret the result in context.
Before you start2 quick questions on what this builds on
Revise first: 3.4 Arc length and sector area
Measuring angles in radians
So far you have measured angles in degrees, with in a full turn. That number was chosen long ago, and nothing about a circle forces it.
A uses the circle itself. Take the radius as your ruler, and measure an angle by how many radius-lengths of it cuts off at the edge.
θ = °
Arc length s = rθ =
Sector area A = ½r²θ =
It starts at with : the arc is , the same as the radius. Change and the arc still equals . Slide up until the slice fills the circle, at about . The widget calls the arc ; the booklet calls it .
Why ? The circumference is , so a whole circle holds radius-lengths of arc. A full turn is radians, and a half turn is radians.
Every conversion comes from that one fact. One degree is radians, and one radian is degrees, a little under .
An angle written with no degree sign is in radians. You may give it as an exact multiple of , such as , or as a decimal, such as . If the question says "exact", keep the .
Try it first, then reveal one step at a time.
- Multiply by : .
- Simplify the fraction. Divide the top and bottom by : .
- So radians. As a decimal, that is .
- Check: is between a half turn and a full turn, and is between and .
Try it first, then reveal one step at a time.
- Multiply by : .
- Work out the decimal:
- Round only at the end: .
- Interpret: is a bit less than , so the head turns a bit less than a half turn. fits.
Arc length and sector area in radians
In 3.4 a with angle was the fraction of the circle. With in , a full turn is , so the fraction is .
The is that fraction of the circumference: . The area is that fraction of the circle: . The cancels, which is why radians give such short formulas.
Both are in the formula booklet, so you don't need to memorise them. In each, is the radius and must be in radians. If you are given degrees, convert first, or use the degree formulas from 3.4.
The rest carries over from SL. The perimeter of a sector is the arc plus two radii, . The major sector made by two radii has angle , where is the minor sector's angle.
Try it first, then reveal one step at a time.
- The lit ground is a sector with and , already in radians.
- Substitute into : .
- Simplify: , about .
- Check: is a third of a full turn, and a third of the circle is .
Try it first, then reveal one step at a time.
- Arc: m.
- Perimeter: the arc plus two radii, m.
- Fence length: leave out the gap, m.
- Cost: dollars.
- Interpret: this assumes the fence follows the curve exactly with no waste, so a real order would add a little.
Finding the radius or the angle
Sometimes you know the arc or the area and need or . Write the formula with the numbers you know, then solve for the unknown. With radians this is often one step: .
Try it first, then reveal one step at a time.
- A point on the tyre travels the same distance as the bike, so the arc is m and m.
- Write the arc formula with what you know: .
- Rearrange: radians.
- Interpret: a full turn is , so the wheel turns a little less than once.
Two facts about one sector give two equations in and . Use one to replace (or ) in the other, then solve the equation that is left.
Try it first, then reveal one step at a time.
- Perimeter: , so the arc is .
- Area: . This gives , so . Write this line down: it earns the method mark.
- Solve on the GDC: or .
- Find each angle from : gives , and gives .
- Interpret: is more than , so reject it. The badge has radius cm and angle radians.
The formulas and have no sine or cosine, so your GDC's angle mode doesn't change them. The mode matters as soon as , or meets an angle in radians.
Try it first, then reveal one step at a time.
- Set your GDC to radian mode. The glass is the sector minus the triangle .
- Sector: .
- Triangle: two sides of with radians between them, so .
- Glass: .
- Check: degree mode would read as and wrongly give .
Common mistakes
- Putting an angle in degrees into or . Convert it to radians first.
- Giving an angle in degrees when the question asks for radians. Answer in the unit asked for.
- Giving the arc as the perimeter. A sector's perimeter is , so add the two radii.
- Finding in degree mode for an angle in radians. Set radian mode first.
- Rounding too early, such as rounding a sector's area before subtracting a triangle. Keep the full GDC values until the final answer.
- Giving answers to more than 3 s.f. when no accuracy is stated. Round the final answer to 3 s.f. (an angle in degrees to 1 d.p.), or leave it exact.
Exam tips
- Find the exact value: leave in, as in . Otherwise give 3 s.f.; a radian angle such as needs no unit sign.
- Find or calculate: write the formula with your numbers substituted, such as , before the answer. That line earns the method mark.
- Solve from two facts about a sector: write both equations, then the one equation you put into the GDC. Reject any solution that breaks a stated condition, such as .
- Show that an angle rounds to a given value: write a more accurate value first, such as , then the given .
Key takeaways
Practise this
3 past-paper questions on Radian measure in the AI HL bank, each with a mark scheme and a worked explanation.