Arc length and sector area
In a minute
A is a slice of a circle, and its is the curved edge. With the angle at the centre in degrees, both are a fraction of the whole circle: of the circumference for the arc, of the area for the sector. Exams set them in real shapes, often inside a shaded region.
You'll be able to
- Find the length of an arc and the area of a sector from the radius and the angle in degrees.
- Find the perimeter of a sector, and work with major sectors.
- Work backwards from an arc or an area to the angle or the radius, using your GDC where it helps.
- Find shaded areas made from sectors, such as rings and segments, and interpret them in context.
Before you start3 quick questions on what this builds on
Revise first: 3.2 Triangle trigonometry
Arc length and sector area
A sprinkler turning through part of a circle wets a slice of lawn with a curved outer edge. How big is the slice, and how long is its edge?
Say the angle at the centre is degrees. A full turn is , so the sector is the fraction of the whole circle.
So its arc is of the circumference . Its area is of the circle's area .
Both are in the formula booklet, so you don't need to memorise them. In each, is the radius and is the angle at the centre in degrees. At SL you always work in degrees.
Try it first, then reveal one step at a time.
- The wet patch is a sector with m and .
- Substitute into the sector formula: . This line earns the method mark.
- .
- Check: is a bit less than a third of a turn. A third of the circle, , is a bit more.
The perimeter of a sector is the whole way round its edge: the arc plus two straight radii. So the perimeter is .
Try it first, then reveal one step at a time.
- Arc: m.
- Perimeter: arc plus two radii, m.
- Number of lengths:
- Interpret: lengths only cover m and leave a gap, so round up to .
Two radii split a circle into two sectors. The smaller is the minor sector, with angle . The larger is the major sector, and its angle is the rest of the turn, .
Finding the angle or the radius
Sometimes you know the arc or the area and need the angle or the radius. Write the formula with the numbers you know, then solve for the unknown.
Try it first, then reveal one step at a time.
- The radius is the pendulum's length, cm.
- Write the arc formula with what you know: .
- Rearrange:
- Check: cm is just under a tenth of the circumference, about cm. A tenth of is , so is sensible.
When the radius is unknown, the area equation has in it. Rearrange and take the square root, or use your GDC. Write the equation down first.
Try it first, then reveal one step at a time.
- Write down the equation: . This line earns the method mark.
- Solve it on the GDC with a positive starting guess, such as :
- Interpret: also gives , but a length can't be negative, so reject it.
- Check by hand: , and
Shaded regions: rings and segments
Many exam shapes are built from sectors. Find the area of each piece, then add or subtract.
A ring sector lies between two arcs with the same centre and the same angle. Its area is the big sector minus the small one: .
Try it first, then reveal one step at a time.
- Big sector: .
- Small sector: .
- Path: . Subtract the full values, not rounded ones.
- Check: the path is m wide and its middle arc, of radius m, is about m long. .
A chord is a straight line joining two points on a circle. It cuts a minor sector () into a triangle and a segment: the piece between the chord and the arc.
So the segment's area is the sector's area minus the triangle's. The triangle has two sides with the angle between them, so its area is (3.2).
Try it first, then reveal one step at a time.
- (a) Set your GDC to degree mode. Sector: .
- Triangle: .
- Segment: .
- (b) The whole table is , so .
- Interpret: about an eighth of the tabletop is lost to fit the wall.
Common mistakes
- Giving the arc as the perimeter. A sector's perimeter is the arc plus two radii.
- Using the minor angle for a major sector. The larger sector's angle is , so check which region the question means.
- Working out in radian mode. Set degree mode before any trig on the GDC.
- Rounding a sector's area before subtracting. Keep the full GDC values and round only the final answer.
- Using the width of a ring, , as a radius. Find both sectors, then subtract.
Exam tips
- Find or calculate: write the formula with your numbers substituted, such as , before the answer. That line earns the method mark.
- Show that: substitute into the formula and give your unrounded value, such as , before the rounded one asked for. Never work backwards from the given answer.
- Determine which region is larger: work out both areas, state which is larger, and give the difference with units.
Key takeaways
Practise this
11 past-paper questions on Arcs and sectors in the AI HL bank, each with a mark scheme and a worked explanation.