Areas and volumes of revolution
In a minute
A counts area below an axis as negative, so an area adds the sizes of the parts. Turn a region once about the - or -axis and it sweeps out a solid, whose adds up thin discs.
You'll be able to
- Find the area between a curve and the -axis when part of it is below the axis.
- Find the area between a curve and the -axis by integrating with respect to .
- Find the volume of revolution of a region rotated a full turn about the -axis.
- Find the volume when a region is rotated about the -axis, and interpret it.
- Write each area or volume as an integral, then evaluate it on your GDC.
Before you start2 quick questions on what this builds on
Revise first: 5.5 Antidifferentiation, definite integrals and area
Areas and negative integrals
In 5.5 every region was above the -axis, so its definite integral was its area. Now let the curve dip below the axis.
Each thin strip adds to the total. Below the axis is negative, so a region below the -axis gives a negative integral.
An area is never negative, so the booklet uses the modulus : the size of without its sign. The first form is the area between a curve, the -axis and the lines and .
It is in the booklet, so you don't need to memorise it. The form is for the -axis, in the next section.
1. Find where the curve crosses the -axis between and (solve , or use your GDC's zero tool).
2. Integrate separately between neighbouring crossings. A part below the axis gives a negative value.
3. Add the sizes of the parts. Or integrate on your GDC in one go, with its abs( function (check on your model).
Try it first, then reveal one step at a time.
- The curve meets the axis where , at and . At , , so the channel is below ground.
- Integrate: .
- It is negative because the region is below the axis. The area is its size:
- Interpret: a full channel carries about of water in each cross-section.
Try it first, then reveal one step at a time.
- (a) The GDC gives . That can't be the area: the graph encloses two regions.
- (b) Test a point in each part. At , , so the curve is above the axis for . At , , so it is below for .
- Split at . The GDC gives and . They cancel, which is why (a) gave .
- Add the sizes: . gives the same in one line.
Area between a curve and the y-axis
A region against the -axis is easier to cut into horizontal strips. The strip at height runs from the -axis to the curve: length , thickness .
Adding them gives the second booklet form, , where and are -values. Left of the -axis , so the integral there is negative.
1. Rewrite the curve as in terms of .
2. Find the limits as -values, where the region starts and stops.
3. Integrate with respect to . Take the size of any negative part.
Try it first, then reveal one step at a time.
- It meets the -axis where : , so and .
- At , . The region is left of the -axis, so expect a negative integral.
- .
- The area is its size: .
If the curve is given as in terms of , make the subject first.
Try it first, then reveal one step at a time.
- The region is against the -axis, so integrate in . Make the subject: , and , so .
- The region runs from up to . Write down , typed with for .
- The GDC gives .
- Check: at , . The by rectangle, minus the area under the curve, , is .
- Interpret: of wall needs paint.
Volumes of revolution
Rotate a region one full turn ( radians, or ) about an axis and it sweeps out a solid, such as a bowl, a vase or a nose cone.
About the -axis, slice the solid at right angles to the axis. The slice at is a thin disc of radius and thickness , so its volume is about .
Disc radius f(x₀) = , area =
V = π∫₀ᵇ x dx = πb²/2
V =
Adding every disc from to gives , because .
Both forms are in the booklet. The first rotates the region between a curve and the -axis about the -axis, with -limits. The second does the same with the -axis, with -limits.
Try it first, then reveal one step at a time.
- (a) About the -axis, , from to : .
- (b) Square the radius: . So
- Check: a cylinder of radius (the widest disc) and length has volume . The nose cone narrows to a point, so less makes sense.
- Interpret: a solid nose cone needs about of material.
About the -axis, slice horizontally. The slice at height is a disc of radius and thickness . So write in terms of , and use -limits.
Try it first, then reveal one step at a time.
- About the -axis, . runs from up to the rim, .
- Make the subject: , so .
- Write down the integral you key in: . This line earns the method mark.
- The GDC gives , so .
- Check: a cylinder of radius and height holds about . The holder narrows towards the bottom, so less makes sense. It takes about of wax.
If the region doesn't reach the axis of rotation, the solid has a hole. Find the volume without the hole, then subtract the hole's volume.
Common mistakes
- Giving a negative integral as an area, or integrating across a crossing point so the parts cancel. Split at each crossing and add the sizes.
- Using -values as the limits of a integral. Use the -values where the region starts and stops.
- Leaving out , not squaring, or putting in front. About the -axis the volume is .
- Using for a rotation about the -axis. Write in terms of and use .
- Writing only the GDC's value, or rounding a limit early. Write the integral first, and keep full values of GDC limits.
Exam tips
- "Write down an integral" for a volume: show , the squared radius, both limits and or . Each earns marks, so don't evaluate yet.
- "Find the area" with part of the region below the -axis: show the split (or ) and give a positive answer.
- Give areas and volumes to 3 s.f. with units, such as , unless an exact value is asked for. Round only at the end.
Key takeaways
Practise this
18 past-paper questions on Volumes of revolution in the AI HL bank, each with a mark scheme and a worked explanation.