3D distance, midpoint and measurement
In a minute
In 3D, distance is Pythagoras with a third coordinate, and the midpoint averages each coordinate. You'll find volumes and surface areas of pyramids, cones, spheres and hemispheres. Then you'll find lengths and angles inside solids by spotting right-angled triangles.
You'll be able to
- Find the distance between two points in 3D, and their midpoint.
- Find the volume and surface area of , , spheres, and solids built from them.
- Spot right-angled triangles inside a solid and use them to find lengths.
- Find the angle between two lines that meet, and the .
Before you start3 quick questions on what this builds on
Distance and midpoint in 3D
In 3D a point has three coordinates, . Think of and as directions across a floor, and as height above it.
To get from A to B, you move along , then , then . Those moves are three edges of a box, and AB is its .
So use Pythagoras twice: , then . The edges are the differences in the coordinates of A and B.
Here and are the two points and is the distance between them. It is in the formula booklet.
Try it first, then reveal one step at a time.
- Subtract coordinate by coordinate: , and .
- Square each: , and . Squaring removes the signs, so the order of subtraction doesn't matter.
- Add and take the square root: .
The midpoint of a segment is halfway along it. Each of its coordinates is the mean of the matching coordinates of the ends. This is in the booklet too.
For A and B above, the midpoint is .
Notation: is the line segment from A to B, and AB with no arrow is its length. So "find AB" asks for a distance.
Try it first, then reveal one step at a time.
- Write , so there is no square root: .
- Work out the known squares: , so .
- Square root, keeping both signs: or .
- So or . Check : .
Volume and surface area of solids
A pyramid narrows from its base to a point, the apex. It holds one third of the prism with the same base and height.
In a the apex is directly above the centre of the base. The height is measured straight down, at right angles to the base.
is the area of the base, whatever its shape. A is a pyramid with a circular base of radius . Its sloping side has length , the .
is the curved area only; a solid cone also has a circular base, . Use for volume and for area, linked by Pythagoras:
For a sphere of radius :
A is half a sphere: volume , curved surface . A solid one also has a flat face, , so its total surface area is .
All the formulas above except the slant height and hemisphere ones are in the formula booklet. So are the prior-learning ones for circles, cylinders and prisms. What you must know is which length goes where.
Try it first, then reveal one step at a time.
- Slant height first: cm.
- Curved area: .
- Base: .
- Total: .
Try it first, then reveal one step at a time.
- The surface is the base plus four equal triangles. Base: .
- Each triangle's height runs from the apex down the face to the middle of a base edge.
- The middle of an edge is cm from the centre of the base, and the pyramid's height is vertical. So cm.
- One triangle: . Total: .
For a solid built from pieces, add the volumes. For surface area, count only the outside faces: where two pieces join, those faces are hidden.
Try it first, then reveal one step at a time.
- Cube: . Pyramid: .
- Write down the equation you solve: . This earns the method mark.
- Solve it on the GDC (steps below):
- Round at the end: . Check: .
Right-angled triangles inside solids
At SL, 3D questions about solids are set so that right-angled triangles are enough. The skill is finding them.
Right angles come from vertical lines. A vertical height or edge meets every line in the floor through its foot at .
1. Mark what you want on a sketch of the solid.
2. Find a right-angled triangle that contains it, with other sides you know or can find.
3. Draw that triangle flat, with the right angle marked. Then use Pythagoras or SOH CAH TOA.
Try it first, then reveal one step at a time.
- Floor diagonal: , so cm. Keep it exact.
- The vertical edge meets at a right angle, so , that edge and the form a right-angled triangle.
- , so cm.
- Check with the distance formula from to : .
In a , the height VX drops from the apex V to the centre X of the base. So V, X and a corner C make a right-angled triangle, with the right angle at X.
Try it first, then reveal one step at a time.
- Use triangle VXC. The base diagonal is .
- X is halfway along it: .
- VC is the hypotenuse: .
- So cm.
Angles between lines and planes
Two lines that meet make an angle where they cross. Put both lines in one triangle, find a right angle, and use SOH CAH TOA.
To measure how a line leans against a plane (a flat surface), compare it with a line in the plane.
AN is called the projection of the line. Triangle PAN has its right angle at N, so the is never more than .
Try it first, then reveal one step at a time.
- Let the diagonal run from bottom corner P to top corner Q. The corner N is directly below Q.
- QN is vertical, so PN, the floor diagonal, is the projection: .
- In triangle PNQ, is opposite and PN is next to it: .
- So .
Try it first, then reveal one step at a time.
- The two lines and the diameter make an isosceles triangle. The cone's height splits it into two right-angled triangles.
- In one half, the angle at the vertex has the radius opposite and the height next to it: .
- So . Don't round yet.
- The angle between the lines is .
Try it first, then reveal one step at a time.
- A is in the -plane, as . N is directly below B, so is perpendicular to the plane.
- .
- Triangle ANB has its right angle at N, with BN opposite : .
- In degree mode (steps below): .
Without a right angle you would need the sine or cosine rule from 3.2.
Common mistakes
- Leaving out the flat face of a solid hemisphere. Its total surface area is .
- Putting the vertical height into . The curved area of a cone needs the slant height, .
- Using a diameter as the radius. If two points are the ends of a diameter, halve their distance before using a sphere or hemisphere formula.
- Using the whole base diagonal from the centre of the base to a corner. That distance is half the diagonal.
- Leaving the calculator in radian mode. Set degree mode before finding an angle in degrees.
Exam tips
- "Find" a length, area or volume: write the formula with the numbers substituted before the answer. That line earns the method mark.
- Draw the right-angled triangle you use on its own, with the right angle and known sides marked. It shows your method and stops you mixing up sides.
- Keep lengths you reuse exact or unrounded, such as . Round only the final answer, to 3 s.f., and give its units.
Key takeaways
Practise this
5 past-paper questions on 3.1 in the AA HL bank, each with a mark scheme and a worked explanation.