Areas and volumes of revolution
In a minute
A region can be sliced in either direction. Slice it into horizontal strips, and gives its area against the -axis. Spin a region about an axis and it sweeps out a . Slice that into thin discs, and an integral adds up their volumes.
You'll be able to
- Find the area between a curve and the -axis by integrating with respect to .
- Rewrite a curve as in terms of , and use -values as the limits.
- Find the volume of a when a region is rotated about the -axis.
- Find the volume when a region is rotated about the -axis.
- Subtract volumes when the solid has a hole, and use your GDC for volume integrals you can't do by hand.
Before you start2 quick questions on what this builds on
Revise first: 5.11 Definite integrals and areas
Area between a curve and the y-axis
In 5.11 you cut a region into thin vertical strips. Each strip had height and width , so the area was .
A region against the -axis is easier to cut into horizontal strips. A strip at height runs from the -axis to the curve, so its length is and its thickness is .
Adding up the strips gives the area between a curve, the -axis and the lines and :
This is in the formula booklet, so you don't need to memorise it. It is the 5.11 formula with and swapped. The modulus matters when the curve is left of the -axis, where is negative.
1. Rewrite the curve as in terms of .
2. Find the limits as -values. If you are given points, use their -coordinates.
3. Integrate with respect to . If the curve crosses the -axis between the limits, split there, as you did at the -axis in 5.11.
Try it first, then reveal one step at a time.
- The curve is already written as in terms of . It meets the -axis where : , so and .
- Test : . So the region is right of the -axis, and .
- Write the area as an integral in : .
- Integrate and substitute: .
Often the curve is given as in terms of . Then make the subject first. This can turn a hard integral into an easy one.
Try it first, then reveal one step at a time.
- The region sits against the -axis, so integrate with respect to . Make the subject: gives .
- The limits are -values. The -axis is , and the top is . Since , the region is right of the -axis.
- Write the area and integrate: .
- Since , . In you would need and a rectangle taken away, so is the shorter route.
Volume of revolution about the x-axis
Take the region under from to . Rotate it through radians (one full turn, ) about the -axis. It sweeps out a , such as a cone, a bowl or a vase.
Cut the solid at right angles to the -axis. Every slice is a thin disc. The disc at has radius , so its face has area . Its thickness is , so its volume is about .
Disc radius f(x₀) = , area =
V = π∫₀ᵇ x dx = πb²/2
V =
Move and watch the disc's radius follow the curve. Adding every disc from to gives , because .
Both forms are in the formula booklet. The first is for rotation about the -axis, with written in terms of . You'll use the second in the next section.
Try it first, then reveal one step at a time.
- Picture the solid. It is a cone with its tip at the origin. Its base is the circle at , with radius .
- Write the volume: .
- Integrate: .
- Check with the cone formula from 3.1: .
Now take a region between two curves, with above and both . Rotating it gives a solid with a hole down the middle. Each slice is a disc of radius with a smaller disc of radius cut out, like a washer.
This is the outer volume minus the volume of the hole. It is not . Square each radius, then subtract.
Try it first, then reveal one step at a time.
- Find where the curves meet: , so , and or .
- At , and . So gives the outer radius and the inner radius. Both are for .
- Write the volume: .
- Integrate: .
- Simplify: .
On Paper 2 you often can't do the volume integral by hand. Write it down, then let your GDC evaluate it.
Try it first, then reveal one step at a time.
- The curve passes through the origin, since , and . So no part of is below the axis, and the radius at is .
- Write down the integral you key in: . This line earns the method mark.
- The GDC gives
- Check: the radius reaches , so the solid fits inside a cylinder of volume .
- Round only at the end: to 3 s.f.
Volume of revolution about the y-axis
Rotate a region about the -axis instead, and slice the solid horizontally. The slice at height is a disc of radius and thickness . Its volume is about .
Adding the discs gives the second booklet form, . The method swaps the roles of and :
1. Rewrite the curve as in terms of . You often don't need itself.
2. Use -values as the limits.
3. Integrate with respect to .
Try it first, then reveal one step at a time.
- The axis of rotation is the -axis, so use .
- Rewrite the curve: gives . There is no need to take a square root.
- The region runs from the lowest point of the curve, , up to . These are the limits.
- Integrate: .
When you make the subject, one may give two values of . Pick the one that matches the region.
Try it first, then reveal one step at a time.
- The curve meets the -axis at and touches the -axis at . The region lies between them, with .
- Make the subject: , so . The region has , so take .
- The region runs from to . Write the volume: .
- Expand the bracket: .
- Integrate: .
- Check: the solid fits inside a cylinder of radius and height , of volume , and it narrows to a point at the top. So a much smaller answer makes sense.
needs the region to reach the -axis. If it doesn't, the solid has a hole down the middle. Find the volume without the hole, then take away the hole, just as with washers. Each piece gets its own -limits.
Try it first, then reveal one step at a time.
- The region starts at , so it doesn't reach the -axis. The solid has a hole down the middle.
- Without the hole, the solid is a cylinder of radius . Its height runs from up to the curve at , which is . Its volume is .
- The hole has two parts. Below (the curve's height at ), the inner edge is the line . That part is a cylinder of radius and height , with volume .
- Above , the inner edge is the curve. Make the subject: , so . This part runs from to : .
- Take away the hole: .
- Check the limits. Taking away instead would give . That is too big: below the hole reaches out to , not just to the curve.
Common mistakes
- Using the wrong formula for the axis. About the -axis it is , not , so rewrite the curve as in terms of .
- Using -values as the limits of a integral. Find the -coordinates where the region starts and stops.
- Putting before the integral, or leaving the radius unsquared. The volume is . Rotating through or just means one full turn.
- Squaring the gap between two curves. Use , not .
- Forgetting the hole. When the region doesn't reach the axis of rotation, subtract the volume of the hole. If the outer and inner parts span different heights, give each integral its own limits.
Exam tips
- "Find the volume": write the integral, with , the squared radius and the limits, before you evaluate it. That line earns the method marks.
- On Paper 1, leave a volume exact as a multiple of , such as . On Paper 2, give 3 s.f. unless told otherwise, and round only at the end.
- "Show that" a volume equals a given expression: start from (or ) and write every step. A GDC value can't show an exact result.
Key takeaways
Practise this
10 past-paper questions on 5.17 in the AA HL bank, each with a mark scheme and a worked explanation.