Definite integrals and areas
In a minute
A is the change in an antiderivative: . You'll evaluate one exactly by hand, then use it to find areas. That includes regions below the -axis, where the integral is negative, and regions between two curves.
You'll be able to
- Evaluate a exactly, using .
- Recognise a definite integral you can't do by hand, and evaluate it on your GDC.
- Find the area between a curve and the -axis when some or all of it lies below the axis, writing the integral first.
- Find the area enclosed between two curves, by hand or with your GDC.
Before you start3 quick questions on what this builds on
Revise first: 5.5 Antidifferentiation, definite integrals and area and 5.10 Indefinite integration and substitution
Definite integrals by hand
On Paper 1 there is no GDC, and answers are often exact, such as . An gives you the exact value of a .
Here is the idea. is the rate at which changes. Adding up from to gives the total change in , which is .
This is the . The numbers and are the : is the lower limit and the upper limit.
In practice you call the antiderivative , so . Square brackets with the limits are shorthand for upper minus lower.
You don't need here. It would appear twice, as , and cancel.
1. Integrate, leaving out . Write the result in square brackets with the limits.
2. Substitute the upper limit, then the lower limit.
3. Subtract: upper minus lower. Put the lower value in brackets, because all its signs change.
Try it first, then reveal one step at a time.
- Integrate term by term, without , and write the limits on the bracket: .
- Substitute the upper limit, : .
- Substitute the lower limit, : .
- Subtract, upper minus lower, with the lower value in brackets: .
Try it first, then reveal one step at a time.
- The inside, , is linear, and the number in front of is . As in 5.10, , so .
- Write it with the limits: .
- Use the log law : .
- Check: . The integrand falls from to over a width of , so the value lies between and .
Some definite integrals can't be done by hand. For example, has no antiderivative made from the functions you know. Its definite integrals still have values, but only technology can find them.
Try it first, then reveal one step at a time.
- You can't integrate by hand, so evaluate the integral numerically on your GDC.
- Write down what you key in: . The GDC gives
- Check: the integrand lies between and over a width of , so the value lies between and .
- Round only at the end: to 3 s.f.
Area when the curve goes below the x-axis
Think of the thin rectangles from 5.5. Each strip adds to the total. Below the -axis is negative, so every strip there adds a negative amount.
So a definite integral counts area below the axis as negative. When a curve crosses the axis, the parts above and below cancel. For example, , yet and the axis enclose two humps, each of area .
An area is never negative. The formula booklet gives the area between , the -axis and the lines and as:
Here is the modulus of : its size, without its sign. It flips the parts below the axis up, so every part counts as positive.
Without technology, you split the interval wherever the curve crosses the axis.
1. Solve to find where the curve meets the -axis between and .
2. Integrate separately between each pair of neighbouring limits and roots.
3. Take the size of each value, ignoring its sign, then add.
Try it first, then reveal one step at a time.
- Find where the curve meets the axis: , so and .
- Decide whether the region is above or below the axis. Test : . So the region is below the axis.
- Write the area as an integral: .
- Integrate and substitute: .
- The integral is negative because the region is below the axis. The area is its size: .
Try it first, then reveal one step at a time.
- Factorise: . At , , so the curve is above the axis for . At , , so it is below for .
- Write the area first: . The minus sign turns the part below the axis positive.
- Let . Then , and .
- First part: . Second part: , which has size .
- Add the sizes: .
- Compare: one integral from to gives . The parts cancel, which is why you split.
You met the same idea in 5.9: displacement is , but distance travelled is .
Area between two curves
Take two curves, with above from to . The area under the top curve, minus the area under the bottom one, leaves just the region between them.
In strips: each thin strip runs from the bottom curve to the top one, so its height is .
Top minus bottom stays positive even below the -axis. So you split only where the curves cross, not at the -intercepts.
They meet at x = −1 and x = 2
Area from x = −1 to x = b =
Slide : the shaded area always equals .
1. Find where the curves meet: solve .
2. Decide which curve is on top between those points. Test one value.
3. Write , with the meeting points as limits.
4. Evaluate it.
Try it first, then reveal one step at a time.
- Find where they meet: , so and . They meet at and .
- Test : the line gives and the curve gives . So the line is on top.
- Write the area, bracketing the bottom curve so every term is subtracted: .
- Integrate: .
- Simplify: .
- The curve is below the -axis for , but top minus bottom is still the strip height there, so no split is needed.
If the curves cross between the limits, top and bottom swap over. Split at each crossing and find each area separately, just as you split at the -axis before.
When you can't solve by algebra, use your GDC for the meeting points and then the integral. The graph also shows which curve is on top.
Try it first, then reveal one step at a time.
- Set your GDC to radians. In calculus, in is always in radians.
- Graph both functions and find where they meet: and Keep at least six significant figures, or store the values.
- Decide which is on top: at , and . So is on top.
- Write down what you key in: .
- The GDC gives , so to 3 s.f.
Common mistakes
- Giving a negative integral as the area. An area is never negative: split at the -intercepts and add the sizes of the parts.
- Subtracting the wrong way round between two curves. Test a point to find the top curve, then integrate top minus bottom.
- Treating the lower limit as if it gives . Since and , always substitute it: .
- Adding the curves instead of subtracting. The strip height is the gap between them: for above it is , not .
- Slips with a linear inside. : divide by , and keep its sign.
Exam tips
- "Find the area": write the integral with its limits first, such as . That line shows your method even if a later step slips.
- On Paper 1, show the square bracket and both limits substituted, and leave the answer exact, such as .
- On Paper 2, write down the integral you key in. Use the meeting points to at least six significant figures (or store them), and round only the final answer to 3 s.f.
Key takeaways
Practise this
30 past-paper questions on 5.11 in the AA HL bank, each with a mark scheme and a worked explanation.