Scale drawings
In a minute
A shrinks every real length by the same amount, so you multiply or divide by the scale. A gives a direction as a three-figure angle, turning clockwise from north. Together they let you find distances and mark places on a map.
You'll be able to
- Use a scale to change a length on a drawing into a real distance, and back again.
- Make a scale drawing from real measurements, with a ruler for every straight line.
- Measure and draw three-figure , including bearings past .
- Mark a point on a scale drawing from its distance and bearing.
- Find the bearing of A from B when you know the bearing of B from A.
Before you start2 quick questions on what this builds on
Revise first: 1.11 Ratio and proportion and 4.2 Geometrical constructions
Using a scale
A is an accurate picture of something too big to draw full size, such as a field or a coastline. Every length is shrunk by the same amount, so the shape and the angles stay the same.
" to " (or " represents ") means each centimetre on the drawing stands for in real life.
From the drawing to real life, multiply the drawing length by the scale. From real life to the drawing, divide the real length by the scale.
A works the same way, but both parts are in the same unit (centimetres on the map stand for centimetres in real life), so change units at the end. Every length uses the same , an idea you meet again in 4.4.
Try it first, then reveal one step at a time.
- Each centimetre on the plan stands for .
- There are centimetres, so multiply: .
- Check the size: cm is a bit more than cm, so the answer should be a bit more than . fits.
Try it first, then reveal one step at a time.
- Each centimetre stands for , so divide each real length by .
- Dividing by is easier if you double both numbers first. Length: cm.
- Width: cm.
- Rule a cm line. Use a protractor to draw a cm line at right angles at each end, then join their ends with a ruler.
Three-figure bearings
A gives a direction as an angle. You always start facing north and turn clockwise, the way a clock's hands move.
So north is , east is , south is and west is . "D is due east of C" means D is exactly on a bearing of from C.
"The bearing of B from A" means you stand at A. Draw the north line at A, put the protractor's centre on A with on the north line, and measure clockwise round to the line AB.
Always write three figures. An angle of is the bearing , and is .
A protractor only reaches . For a point to the left of the north line, measure the angle anticlockwise from north instead. The bearing is minus that angle.
Try it first, then reveal one step at a time.
- T is to the left of the north line, so the bearing is more than .
- The clockwise turn and the anticlockwise turn together make a full turn of .
- So the bearing is . It is between west () and north, as T is.
Try it first, then reveal one step at a time.
- Length on the drawing: cm.
- Rule a north line at L. The bearing is past , so measure anticlockwise from north, and mark it.
- Check the direction: is between south () and west (), so Y is below and to the left of L.
- Rule a line from L through your mark. Mark Y on it, cm from L, and label it.
Turning a bearing round
Often you know the bearing of B from A and need the bearing of A from B. North points the same way everywhere on a map, so the north lines at A and B are parallel.
The two angles are between the parallel north lines. So from B you turn to face south, then more to face A.
Try it first, then reveal one step at a time.
- is less than , so add .
- .
- Check with the figure: A is below and to the left of B, between south and west. is between and .
Try it first, then reveal one step at a time.
- is more than , so subtract .
- .
- Adding would give , more than a full turn, so it cannot be a bearing.
- Check: Q is north-west of P, so P is south-east of Q. is between east and south.
Common mistakes
- Measuring anticlockwise, or from the south line. Every bearing starts on the north line and turns clockwise.
- Measuring at the wrong point. For the bearing of A from B, put the protractor on B.
- Giving the drawing length as the answer. Multiply by the scale and convert to the unit asked for, such as km.
- Dropping the leading zero. A bearing of is written .
- Reading the wrong scale on the protractor. Use the scale that reads on the north line.
Exam tips
- "Measure the bearing": centre the protractor on the point after "from", with on the north line, and write three figures. A small range is accepted, so measure carefully.
- "Work out the actual distance": write down the length you measured, then multiply by the scale. The measurement on its own can earn a mark.
- "Mark the position": rule a line on the right bearing, mark the point at the scaled length, and label it with its letter. Use a ruler for every straight line.
Key takeaways
Practise this
40 past-paper questions on 4.3 in the 0580 Extended bank, each with a mark scheme and a worked explanation.