Geometrical constructions
In a minute
You measure lines with a ruler and angles with a protractor, and you build a triangle from its three sides with compasses. You also fold flat into solids and read lengths off them. The arcs you draw are part of the answer, so leave them in.
You'll be able to
- Measure and draw lines to the nearest millimetre, and angles to the nearest degree, including reflex angles.
- Construct a triangle from its three sides with a ruler and compasses, leaving the arcs showing.
- Construct a rhombus by building two triangles on one diagonal.
- Draw of cubes, cuboids, prisms and pyramids, and say which meet when a net folds.
- Use the lengths on a net to find a solid's surface area and volume.
Before you start2 quick questions on what this builds on
Revise first: 4.1 Geometrical terms
Measuring lines and angles
A ruler is marked in centimetres, and each centimetre has 10 small marks of . So .
Put the zero mark, not the end of the ruler, on the start of the line. If the zero is worn away, subtract the start reading from the end reading. To draw a line, mark zero and the length, then rule between them.
Try it first, then reveal one step at a time.
- Change both readings to millimetres. The start is .
- The end is and 4 small marks: .
- Subtract the start from the end: .
A protractor has two scales running in opposite directions. Put its centre on the and lay one arm along the base line. Read the scale that shows on that arm.
A protractor only reaches . For a , use the angle on the other side: the two add up to .
Try it first, then reveal one step at a time.
- The two angles at make a full turn, so the other one is .
- Rule a base line from . With the protractor's centre on , mark on the scale that reads on the base line.
- Rule a line from through the mark. Draw the angle arc on the outside, so the marked angle is the reflex one.
Constructing a triangle from three sides
Compasses mark every point at one distance from the centre. The third corner must be the right distance from both ends of the base, so it sits where two cross.
1. Rule one side, or use the side already drawn.
2. Open the compasses to the second length against the ruler. Centre them on the correct end and draw an arc.
3. Do the same with the third length from the other end, cutting the first arc.
4. Rule lines from both ends to the crossing. Leave the arcs in.
Try it first, then reveal one step at a time.
- Rule and label its ends.
- starts at . Open the compasses to , centre them on , and sweep an arc above .
- starts at . Open them to , centre them on , and sweep a second arc to cut the first. Label the crossing .
- Rule and , leaving both arcs.
- Measure at with the protractor's on : about .
You only get a triangle if the two shorter sides add up to more than the longest side. If they add up to less, the arcs never meet. If they add up to exactly the longest side, the arcs meet on the line itself, so there is no triangle.
A rhombus has four equal sides, and a diagonal splits it into two triangles. So build two triangles on one diagonal.
Try it first, then reveal one step at a time.
- Rule .
- Open the compasses to . Sweep arcs from and from above the line, and label the crossing .
- Keep the setting and repeat below the line to find .
- Rule the four sides, leaving all four arcs. Then rule and measure it: about .
Nets of solids
To see which faces of a cube end up opposite, fold the net in your head one square at a time.
To draw a net, rule one face, then join each neighbouring face along an edge of the same length. A needs its two ends plus a rectangle for each side of an end. A needs its base plus a triangle on each edge of the base.
The is the total area of all the faces, which is the area of the net. For , read the solid's lengths off the net. A cuboid's volume is length width height.
Try it first, then reveal one step at a time.
- Read the sizes off the net: by by .
- Each rectangle size appears twice: , and .
- Add one of each and double: .
Try it first, then reveal one step at a time.
- Each end is a right-angled triangle with base and height : area .
- The three rectangles are all long: .
- Add the two ends and the three rectangles: .
Common mistakes
- Swapping the two lengths in a construction. The arc for is centred on ; check each arc against the letters before you draw it.
- Rubbing out the construction arcs. They earn marks, so leave them in.
- Measuring from the end of the ruler, or giving centimetres when the question asks for millimetres. Start at zero and read the unit asked for.
- Attaching a face to an edge of a different length when drawing a net. Edges that meet when folded must be equal.
Exam tips
- "Construct" with a ruler and compasses: both arcs must stay visible. A correct triangle with no arcs earns only part of the marks.
- Use a ruler for every straight line, and a sharp pencil. Constructions are usually marked to within .
- "Measure … give your answer in millimetres": write a whole number of millimetres, such as , not .
Key takeaways
Practise this
14 past-paper questions on 4.2 in the 0580 Extended bank, each with a mark scheme and a worked explanation.