Vector equations of lines
In a minute
A straight line is fixed by one point on it and one direction. The , , gives every point on it, one for each value of . Split into , it gives each coordinate on its own, which is how you find where a path meets the ground, a wall or a given point.
You'll be able to
- Write a vector equation of a line from a point and a direction, or from two points, in 2D and 3D.
- Read the point, the direction and the parameter in context, and test whether a point lies on a line.
- Convert between and parametric form, and use parametric form to find the point where a line meets a condition.
Before you start3 quick questions on what this builds on
Revise first: 3.10 Vectors in 2D and 3D
The vector equation of a line
In 2.1 you fixed a line in 2D by a point and a gradient. A line in 3D has no single gradient, so you give its direction as a instead. One point and one direction pin down exactly one line.
Picture standing at a point A on a straight path. You reach every other point on the path by walking some multiple of the path's direction, forwards or backwards. A says this in symbols.
is the of a known point A on the line. is a : any non-zero vector parallel to the line. is the position vector of a general point on the line.
(lambda) is the parameter, a real number. Each value of gives one point: gives A, gives the point one step of further on, and negative values go backwards. As takes every real value, the points fill the whole line.
The formula is in the booklet. Always start with . Without it you have an expression, not an equation. The same equation works in 2D, with two components, and in 3D, with three.
For a line through two points P and Q, start at either point. For the direction, use the displacement .
Try it first, then reveal one step at a time.
- Direction: .
- Start at C: .
- Check: gives , the gate.
- gives : the point , 35 m due north of the entrance.
- Interpret: the path is m long, so this point is a quarter of the way along, 25 m from the café. Values of outside give points on the line beyond the ends of the path.
Try it first, then reveal one step at a time.
- Direction: .
- (a) .
- (b) Set the general point equal to the tower top. From : , so .
- Check the other components with : and . One value of gives all three coordinates, so the tower top lies on the line.
- Interpret: is B and is T, so the tower top is of the way along the cable from the bottom station.
A line has many vector equations. You can start at any point on it, and any non-zero multiple of is also a direction vector. Above, , so gives the same line.
The meaning of changes with the equation, though. With direction , is no longer the top station. So read from the equation you were given.
In 2D, the line passes through and rises for every across. So is a vector equation of it. Going back, a direction with gives the gradient .
Parametric form
A holds two or three equations in one. Write as , the known point as and the direction as . Then each row gives one coordinate.
This is the of the line, and it is in the booklet too. Each coordinate is written in terms of the parameter . In 2D you have only the and equations.
Parametric form is how you use a line. A condition such as “on the ground” () or “at the wall ” gives one equation in . Solve it, then put that into every coordinate. If that coordinate has no term, the line is parallel to the ground or wall: it never meets it, or lies in it.
Try it first, then reveal one step at a time.
- Read off each row: , and .
- On the ground : , so .
- Substitute into the other two: and .
- Interpret: the drone lands 28 m east and 7 m north of the depot, assuming it keeps to the straight line until it touches down.
Going back from parametric to vector form is reading off. The constants give the point and the coefficients of give the direction. A coordinate with no term has direction component .
Try it first, then reveal one step at a time.
- (a) Constants give the start, coefficients of give the direction: .
- (b) At the landing platform, , so . The end point is .
- Displacement from start to end: . That is times the direction vector, as says.
- Write down what you enter: length m.
- Interpret: each unit of moves m along the line, and the rider travels units. The end is still m above the ground, a sensible height for a landing platform.
Common mistakes
- Leaving out . On its own, is an expression, not an equation, and can lose a mark.
- Using a position vector as the direction. For the line through P and Q, the direction is , not .
- Testing a point with one coordinate only. Find from one coordinate, then show that the same gives the others too.
- Mixing up the parts of parametric form: putting a constant into the direction, or forgetting that a coordinate with no term has direction component .
- Rounding before substituting it. Keep the full value and round only the final coordinates or length.
Exam tips
- “Write down” a vector equation: no working is needed, but give the whole equation, starting . The point and the direction vector can earn separate marks.
- “Show that” a point lies on a line: find from one coordinate, substitute it into the others, and state the conclusion. The reasoning mark needs evidence that every coordinate agrees.
- “Find the coordinates” of a point on a line: write the equation you solve for , such as , then substitute. Give coordinates, not a column vector, unless a position vector is asked for.
- “Interpret” in context: say which points and are. In 3.12 the parameter is time and the direction vector is a velocity.
Key takeaways
Practise this
13 past-paper questions on Vector equations of lines in the AI HL bank, each with a mark scheme and a worked explanation.