Rounding, bounds and percentage error
In a minute
Measured and rounded numbers are never quite exact. You'll round to or decimal places, find the and a rounded value came from, and measure how far off an approximation is with . Quick estimates then tell you whether a calculator answer makes sense.
You'll be able to
- Round to a number of decimal places or , and choose an accuracy that suits the data and the context.
- Write down the and of a rounded value, and use bounds in a calculation.
- Calculate a , including the greatest percentage error caused by rounding a measurement.
- Estimate an answer by rounding, and decide whether a result is reasonable in its context.
Before you start2 quick questions on what this builds on
Revise first: 1.1 Standard form
Decimal places and significant figures
To round, look at the digit after the last one you keep. If it is or more, add one to the kept digit; otherwise leave it.
Decimal places (d.p.) count digits after the decimal point. So to d.p. is , and to d.p. is .
has : , , and . To s.f. it is . The zeros in front stay, because they place the digits.
Large numbers keep their place-holding zeros too. to s.f. is , not .
A zero you create by rounding is kept. to s.f. is , not : the final zero shows the answer is accurate to s.f.
IB answers are exact or s.f. unless the question says otherwise; money is usually d.p. Round only the final answer.
When you choose the accuracy, match the data: a result can't be more accurate than the measurements it came from.
The context matters too. If coaches' worth of people need seats, you book coaches. If there is enough paint for fences, you can finish of them.
Try it first, then reveal one step at a time.
- Divide the total by the number of grains: g.
- Find the first non-zero digit. It is the ; the zeros in front of it don't count.
- Keep figures from there: , , . The zero between and counts.
- The next digit is , so round the up to : g.
Try it first, then reveal one step at a time.
- Each length has significant figures.
- The area can't be more accurate than the lengths it came from. So give it to s.f. too.
- to s.f.: the digit after the is , so round up to .
- would claim an accuracy the tape measure can't give.
Upper and lower bounds
A seedling's height is recorded as cm to d.p. Its true height is some value that rounds to .
Any height from cm up to, but not including, cm rounds to . A height of exactly cm would round up to .
So the seedling's height has cm and cm: . You may also write this as an interval, .
For significant figures, first find the place value of the last figure kept. to s.f. is rounded to the nearest , so the true value lies in .
Try it first, then reveal one step at a time.
- The third significant figure, , is in the tens place. So is rounded to the nearest .
- Half of is . Lower bound: . Upper bound: .
- The true value can equal the lower bound but not the upper bound.
Bounds also feed into calculations. For positive quantities, a product is largest when every factor is at its upper bound. A quotient is largest when is at its upper bound and at its lower bound.
Try it first, then reveal one step at a time.
- Bounds: and .
- (in the prior-learning part of the formula booklet). Both and are positive, so the largest volume uses both upper bounds.
- m³.
- So the tank holds less than m³, well above the m³ the rounded measurements give.
Percentage error
An estimate, a rounded value or a measurement is usually a little off. says how far off, as a percentage of the exact value.
is the approximate value (an estimate, rounded value or measurement). is the exact, or accepted, value. The formula is in the booklet.
The bars make a percentage error never negative. Put both values in the same units first.
Try it first, then reveal one step at a time.
- Here (the estimate) and (the exact value).
- Substitute: .
- Round to s.f.: .
- In context: his estimate is about more than the true area.
A rounded measurement makes any result built from it uncertain. You can find the largest percentage error the rounding could cause.
1. Work out the result from the rounded measurement. This is .
2. Work out the result at the lower and upper bounds. Each is a possible (the true value can get as close to the upper bound as you like).
3. Find the percentage error for each bound. The larger one is the maximum percentage error.
Try it first, then reveal one step at a time.
- Her area: m².
- Bounds for the radius: . Areas: and m².
- Lower bound: .
- Upper bound: .
- The larger is . Her area could be up to about too big. That is about twice the radius's own error of , because the radius is squared.
Estimating and checking answers
An estimate is a quick, rough answer. Round each number to s.f., then work it out in your head or on paper.
If your GDC answer is far from the estimate, look for a typing slip, a missing bracket or a wrong unit.
Then check the answer makes sense in context. A length, area, mass or time taken can't be negative, and a count of people is a whole number.
Try it first, then reveal one step at a time.
- Seconds in a year: . Rounded to s.f., that is about .
- Estimate: km.
- GDC: enter .
- To s.f. that is km. It is close to the estimate, so the calculator entry is reasonable.
Try it first, then reveal one step at a time.
- The length is , so the area gives , which is .
- Use the GDC's polynomial solver with coefficients , , : or .
- A width can't be negative, so reject .
- Check: m². The width is m.
Common mistakes
- Dividing by the approximate value in a percentage error. The exact value always goes in the denominator.
- Mixing units in a percentage error. Change litres and millilitres (or metres and centimetres) to the same unit before you substitute.
- Rounding in the middle of a calculation. Rounding before using it again changes the final digits; keep the full value and round once at the end.
- Writing an upper bound as , or with . The upper bound is , and the true value is strictly less than it.
- Dropping place-holding zeros. to s.f. is , not .
- Keeping a negative solution for a length or a time taken. Reject it, and say why.
Exam tips
- "Write down" a bound: no working is needed, but give the exact bound (, not ). If an inequality or interval is asked for, give both ends.
- "Find" or "calculate" a percentage error: write the formula with your numbers substituted for the method mark, then the answer to s.f. with the sign.
- "Determine whether it is certain": use the extreme bound, compare it with the limit, and state a conclusion in the context of the question.
- Keep full calculator values for later parts. A wrong earlier answer used correctly can still earn follow-through marks.
Key takeaways
Practise this
12 past-paper questions on Rounding, estimation and percentage error in the AI HL bank, each with a mark scheme and a worked explanation.