1 (a) Complete Table 1.1 by stating whether each of the quantities is a vector or a scalar. [2] Table 1.1 quantity | vector or scalar acceleration | power | work | (b) The variation with time t of the velocity v of an object is shown in Fig. 1.1. [Graph: v / m s^-1 against t / s. Straight line rising from 0.70 m s^-1 at t = 0 to 1.40 m s^-1 at t = 4.0 s, horizontal at 1.40 m s^-1 to t = 8.0 s, then straight line falling to 0 at t = 12.0 s.] (i) Determine the acceleration of the object from time t = 0 to time t = 4.0 s. acceleration = ... m s^-2 [2] (ii) Determine the distance moved by the object from time t = 0 to time t = 4.0 s. distance = ... m [2] (c) (i) Define force. [1] (ii) The motion represented in Fig. 1.1 is caused by a resultant force F acting on the object. On Fig. 1.2, sketch the variation of F with time t from t = 0 to t = 12.0 s. Numerical values of F are not required. [3] [Diagram: blank grid with F on the vertical axis (zero line in the middle) and t / s from 0 to 12.0 on the horizontal axis.] [Total: 10]
A Level Physics 9702 · Paper practice
Paper 2 past paper questions
Every archived Physics 9702 Paper 2 question in one place. Practise them by topic, then sit a full paper under timed conditions.
Most-tested topicsDynamics 65Work, energy and power 65Electricity 53Forces, density and pressure 52Waves 52Kinematics 50
You’re practising 2020–2021 papers. The 2022–2026 papers, including 2026, need a plan.
Unlock from $6/mo1 (a) Define density. [1] (b) Fig. 1.1 shows a solid pyramid with a square base. [Diagram: a pyramid with square base, labelled pyramid, density ρ, mass m; height h marked from apex to base and base side length x marked.] The mass m of the pyramid is given by m = (1/3) ρ h x^2 where ρ is the density of the material of the pyramid, h is the height, and x is the length of each side of the base. Measurements are taken as shown in Table 1.1. Table 1.1 quantity | measurement | percentage uncertainty m | 19.5 g | ± 2% x | 4.0 cm | ± 5% h | 4.8 cm | ± 4% (i) Calculate the absolute uncertainty in length x. absolute uncertainty = cm [1] (ii) The density ρ is calculated from the measurements in Table 1.1. Determine the percentage uncertainty in the calculated value of ρ. percentage uncertainty = % [2] (c) The square base of the pyramid in (b) rests on the horizontal surface of a bench. Use data from Table 1.1 to calculate the average pressure of the pyramid on the surface of the bench. The uncertainty in your answer is not required. pressure = Pa [3] [Total: 7]
1 (a) Complete Table 1.1 by stating whether each of the quantities is a vector or a scalar. Table 1.1 quantity | vector or scalar acceleration | electrical resistance | momentum | [2] (b) State the conditions for an object to be in equilibrium. [2] (c) A floating solid cylinder is attached by a wire to the sea bed, as shown in Fig. 1.1. [Diagram: a cylinder, weight 28 N, cross-sectional area 0.0230 m^2, floating partly submerged in water of density 1.00 × 10^3 kg m^-3, its base 0.190 m below the water surface, held by a vertical wire fixed to the sea bed.] Fig. 1.1 (not to scale) The density of the water is 1.00 × 10^3 kg m^-3. The base of the cylinder is at a depth of 0.190 m below the surface of the water. The cylinder has a weight of 28 N and a cross-sectional area of 0.0230 m^2. The wire and the central axis of the cylinder are both vertical. The cylinder is in equilibrium. (i) Calculate, to three significant figures, the upthrust acting on the cylinder due to the water. upthrust = N [2] (ii) Show that the tension T in the wire is 15 N. [1] (iii) The wire has a cross-sectional area of 3.2 mm^2. Calculate the stress in the wire. stress = Pa [2] (iv) The surface of the water gradually rises until it is level with the top face of the cylinder. State and explain, qualitatively, the variation of the strain energy stored in the wire as the water surface rises. [2] [Total: 11]
1 (a) A property of a vector quantity, that is not a property of a scalar quantity, is direction. For example, velocity has direction but speed does not. (i) State two other scalar quantities and two other vector quantities. scalar quantities: … and … vector quantities: … and … [2] (ii) State two properties that are possessed by both scalar and vector physical quantities. 1. … 2. … [2] (b) A ship at sea is travelling with a velocity of 13 m s^-1 in a direction 35° east of north in still water, as shown in Fig. 1.1. [Diagram Fig. 1.1: compass directions N, E, S, W and a velocity arrow of 13 m s^-1 pointing 35° east of north.] (i) Determine the magnitudes of the components of the velocity of the ship in the north and the east directions. north component of velocity = … m s^-1 east component of velocity = … m s^-1 [2] (ii) The ship now experiences a tidal current. The water in the sea moves with a velocity of 2.7 m s^-1 to the west. Calculate the resultant velocity component of the ship in the east direction. resultant east component of velocity = … m s^-1 [1] (iii) Use your answers in (b)(i) and (b)(ii) to determine the magnitude of the resultant velocity of the ship. magnitude of resultant velocity = … m s^-1 [2] (iv) Use your answers in (b)(i) and (b)(ii) to determine the angle between north and the resultant velocity of the ship. angle = … ° [2] [Total: 11]
1 (a) Define density. [1] (b) A smooth pebble, made from uniform rock, has the shape of an elongated sphere as shown in Fig. 1.1. [Diagram: elongated sphere of length L with maximum radius r marked.] The length of the pebble is L. The cross-section of the pebble, in the plane perpendicular to L, is circular with a maximum radius r. A student investigating the density of the rock makes measurements to determine the values of L, r and the mass M of the pebble as follows: L = (0.1242 ± 0.0001) m; r = (0.0420 ± 0.0004) m; M = (1.072 ± 0.001) kg. (i) State the name of a measuring instrument suitable for making this measurement of L. [1] (ii) Determine the percentage uncertainty in the measurement of r. percentage uncertainty = % [1] (c) The density ρ of the rock from which the pebble in (b) is composed is given by ρ = M r^n / (k L) where n is an integer and k is a constant, with no units, that is equal to 2.094. (i) Use SI base units to show that n is equal to -2. [2] (ii) Calculate the percentage uncertainty in ρ. percentage uncertainty = % [3] (iii) Determine ρ with its absolute uncertainty. Give your values to the appropriate number of significant figures. ρ = ( ± ) kg m^-3 [3] [Total: 11]
1 (a) A unit may be stated with a prefix that represents a power-of-ten multiple or submultiple. Complete Table 1.1 to show the name and symbol of each prefix and the corresponding power-of-ten multiple or submultiple. Table 1.1 prefix | power-of-ten multiple or submultiple kilo (k) | 10^3 tera (T) | [blank] ( ) | 10^-12 [2] (b) In the following list, underline all the units that are SI base units. ampere | coulomb | metre | newton [1] (c) The potential difference V between the two ends of a uniform metal wire is given by V = 4ρLI / (πd^2) where d is the diameter of the wire, I is the current in the wire, L is the length of the wire, and ρ is the resistivity of the metal. For a particular wire, the percentage uncertainties in the values of some of the above quantities are listed in Table 1.2. Table 1.2 quantity | percentage uncertainty d | ±3.0% I | ±2.0% L | ±2.5% V | ±3.5% The quantities listed in Table 1.2 have values that are used to calculate ρ as 4.1 × 10^-7 Ω m. For this value of ρ, calculate: (i) the percentage uncertainty. percentage uncertainty = % [2] (ii) the absolute uncertainty. absolute uncertainty = Ω m [1] [Total: 6]
1 (a) A solid cylinder of weight 24 N is made of material of density 850 kg m^-3. The cylinder has a length of 0.18 m, as shown in Fig. 1.1. [Diagram: cylinder with cross-sectional area A, weight 24 N, density 850 kg m^-3, length 0.18 m.] Show that the cross-sectional area A of the cylinder is 0.016 m^2. [3] (b) The cylinder in (a) is attached by a spring to the bottom of a rigid container of liquid, as shown in Fig. 1.2. [Diagram: cylinder fully submerged with its bottom face 0.17 m below the liquid surface, attached by a spring to the bottom of the container; a tap at the bottom of the container side.] Fig. 1.2 (not to scale). The cylinder is in equilibrium with its bottom face at a depth of 0.17 m below the surface of the liquid. The tension in the spring is 8.0 N. (i) Show that the upthrust acting on the cylinder due to the liquid is 32 N. [1] (ii) Calculate the density of the liquid. density = kg m^-3 [3] (c) Fig. 1.3 shows the variation of the tension F with the length of the spring in (b). [Graph: F / N from 0 to 8 against length / cm from 0 to 70; straight line from F = 0 at 30 cm to F = 8 N at 70 cm.] (i) The tap at the bottom of the container is opened so that a fixed amount of liquid flows out of the container. The cylinder moves downwards so that the tension in the spring changes from 8.0 N to 4.0 N. Determine the change in the elastic potential energy of the spring. change in elastic potential energy = J [3] (ii) More liquid is let out of the container until the upthrust on the cylinder becomes 24 N. For the upthrust of 24 N, determine the length of the spring. length = cm [1] [Total: 11]
2 (a) State what is meant by work done. [1] (b) A beach ball is released from a balcony at the top of a tall building. The ball falls vertically from rest and reaches a constant (terminal) velocity. The gravitational potential energy of the ball decreases by 60 J as it falls from the balcony to the ground. The ball hits the ground with speed 16 m s^-1 and kinetic energy 23 J. (i) Show that the mass of the ball is 0.18 kg. [2] (ii) Calculate the height of the balcony above the ground. height = ... m [2] (iii) Determine the average resistive force acting on the ball as it falls from the balcony to the ground. average resistive force = ... N [2] (c) State and explain the variation, if any, in the magnitude of the acceleration of the ball in (b) during the time interval when the ball is moving downwards before it reaches constant (terminal) velocity. [3] [Total: 10]
2 A person uses a trolley to move suitcases at an airport. The total mass of the trolley and suitcases is 72 kg. (a) The person pushes the trolley and suitcases along a horizontal surface with a constant speed of 1.4 m s^-1 and then releases the trolley. The released trolley moves in a straight line and comes to rest. Assume that a constant total resistive force of 18 N opposes the motion of the trolley and suitcases. (i) Calculate the power required to overcome the total resistive force on the trolley and suitcases when they move with a constant speed of 1.4 m s^-1. power = W [2] (ii) Calculate the time taken for the trolley to come to rest after it is released. time = s [3] (b) At another place in the airport, the trolley and suitcases are on a slope, as shown in Fig. 2.1. [Diagram: a trolley with suitcases on a slope at point X; an arrow labelled 18 N points up the slope and an arrow labelled F, 54 N points down the slope; point Y is 9.5 m along the slope from X.] Fig. 2.1 (not to scale) The person releases the trolley from rest at point X. The trolley moves down the slope in a straight line towards point Y. The distance along the slope between points X and Y is 9.5 m. The component F of the weight of the trolley and suitcases that acts along the slope is 54 N. Assume that a constant total resistive force of 18 N opposes the motion of the trolley and suitcases. (i) Calculate the speed of the trolley at point Y. speed = m s^-1 [3] (ii) Calculate the work done by F for the movement of the trolley from X to Y. work done = J [1] (iii) The trolley is released at point X at time t = 0. On Fig. 2.2, sketch a graph to show the variation with time t of the work done by F for the movement of the trolley from X to Y. Numerical values of the work done and t are not required. [Diagram: empty axes, work done on the vertical axis and t on the horizontal axis.] [2] (c) The angle of the slope in (b) is constant. The frictional forces acting on the wheels of the moving trolley are also constant. Explain why, in practice, it is incorrect to assume that the total resistive force opposing the motion of the trolley and suitcases is constant as the trolley moves between X and Y. [1] [Total: 12]
2 A ball is thrown vertically downwards to the ground, as illustrated in Fig. 2.1. [Diagram: a ball with downward speed u released 1.5 m above the ground, and the position at the ground with speed 8.7 m s^-1.] Fig. 2.1 The ball is thrown with speed u from a height of 1.5 m. The ball then hits the ground with speed 8.7 m s^-1. Assume that air resistance is negligible. (a) Calculate speed u. u = m s^-1 [2] (b) State how Newton's third law applies to the collision between the ball and the ground. [2] (c) The ball is in contact with the ground for a time of 0.091 s. The ball rebounds vertically and leaves the ground with speed 5.4 m s^-1. The mass of the ball is 0.059 kg. (i) Calculate the magnitude of the change in momentum of the ball during the collision. change in momentum = N s [2] (ii) Determine the magnitude of the average resultant force that acts on the ball during the collision. average resultant force = N [1] (iii) Use your answer in (c)(ii) to calculate the magnitude of the average force exerted by the ground on the ball during the collision. average force = N [2] (d) The ball was thrown downwards at time t = 0 and hits the ground at time t = T. On Fig. 2.2, sketch a graph to show the variation of the speed of the ball with time t from t = 0 to t = T. Numerical values are not required. [Diagram: empty axes, speed on the vertical axis and t on the horizontal axis, with a dashed vertical line at t = T.] [1] (e) In practice, air resistance is not negligible. State and explain the variation, if any, with time t of the gradient of the graph in (d) when air resistance is not negligible. [2] [Total: 12]
2 (a) Define acceleration. [1] (b) A stone falls vertically from the top of a cliff. Fig. 2.1 shows the variation with time t of the velocity v of the stone. [Graph: v / m s^-1 from 0 to 40 against t / s from 0 to 30; a curve rising steeply from the origin and levelling off to a constant value of about 36 m s^-1 from about t = 20 s.] Fig. 2.1 (i) Explain, with reference to forces acting on the stone, the shape of the curve in Fig. 2.1. [3] (ii) Use Fig. 2.1 to determine the speed of the stone when the resultant force on it is zero. speed = m s^-1 [1] (iii) Use Fig. 2.1 to calculate the approximate height through which the stone falls between t = 0 and t = 30 s. height = m [3] (iv) On Fig. 2.2, sketch the variation with t of the acceleration a of the stone between t = 0 and t = 30 s. [Graph: empty grid, a / m s^-2 from 0 to 20 against t / s from 0 to 30.] [3] [Total: 11]
2 (a) Define momentum. [1] (b) Two balls X and Y, of equal diameter but different masses 0.24 kg and 0.12 kg respectively, slide towards each other on a frictionless horizontal surface, as shown in Fig. 2.1. [Diagram: ball X mass 0.24 kg moving right at 2.3 m s^-1 and ball Y mass 0.12 kg moving left at 2.3 m s^-1 on a frictionless surface.] Both balls have initial speed 2.3 m s^-1 before they collide with each other. Fig. 2.2 shows the variation with time t of the force FY exerted on ball Y by ball X during the collision. [Graph: FY / N from -400 to 400 against t / ms from 0 to 5; a triangular pulse rising linearly from 0 at t = 0 to 240 N at t = 3 ms then falling linearly to 0 at t = 5 ms.] (i) Calculate the kinetic energy of ball X before the collision. kinetic energy = J [3] (ii) The area enclosed by the lines and the time axis in Fig. 2.2 represents the change in momentum of ball Y during the collision. Determine the magnitude of the change in momentum of ball Y. change in momentum = N s [2] (iii) Calculate the magnitude of the velocity of ball Y after the collision. velocity = m s^-1 [2] (c) On Fig. 2.3, sketch the variation with time t of the force FX exerted on ball X by ball Y during the collision in (b). [Graph: empty axes, FX / N from -400 to 400 against t / ms from 0 to 5.] [3] [Total: 11]
2 A charged oil drop is in a vacuum between two horizontal metal plates. A uniform electric field is produced between the plates by applying a potential difference of 1340 V across them, as shown in Fig. 2.1. [Diagram: top metal plate connected to +1340 V, bottom metal plate connected to 0 V, separation 1.4 × 10^-2 m, oil drop of weight 4.6 × 10^-14 N between the plates, uniform electric field.] The separation of the plates is 1.4 × 10^-2 m. The oil drop of weight 4.6 × 10^-14 N remains stationary at a point mid-way between the plates. (a) (i) Calculate the magnitude of the electric field strength. electric field strength = N C^-1 [2] (ii) Determine the magnitude and the sign of the charge on the oil drop. magnitude of charge = C; sign of charge = [3] (b) The electric potentials of the plates are instantaneously reversed so that the top plate is at a potential of 0 V and the bottom plate is at a potential of +1340 V. This change causes the oil drop to start moving downwards. (i) Compare the new pattern of the electric field lines between the plates with the original pattern. [2] (ii) Determine the magnitude of the resultant force acting on the oil drop. resultant force = N [1] (iii) Show that the magnitude of the acceleration of the oil drop is 20 m s^-2. [2] (iv) Assume that the radius of the oil drop is negligible. Use the information in (b)(iii) to calculate the time taken for the oil drop to move to the bottom metal plate from its initial position mid-way between the plates. time = s [2] (c) The oil drop in (b) starts to move at time t = 0. The distance of the oil drop from the bottom plate is x. On Fig. 2.2, sketch the variation with time t of distance x for the movement of the drop from its initial position until it hits the surface of the bottom plate. Numerical values of t are not required. [Graph: empty axes, x / 10^-2 m with 0.7 marked on the vertical axis, t on the horizontal axis.] [2] [Total: 14]
2 (a) State what is meant by work done. [1] (b) Use your answer in (a) to show that the SI base units of energy are kg m^2 s^-2. [1] (c) A metal rod is heated at one end so that thermal energy flows to the other end. The thermal energy E that flows through the rod in time t is given by E = c A (T_1 - T_2) t / L where A is the cross-sectional area of the rod, T_1 and T_2 are the temperatures of the ends of the rod, L is the length of the rod, and c is a constant. Determine the SI base units of c. SI base units … [3] [Total: 5]
3 A spring is extended by a force. The variation with extension x of the force F is shown in Fig. 3.1. [Graph: F / N against x / cm. Straight line through the origin to F = 7.0 N at x = 5.0 cm.] (a) State the name of the law that relates the force and extension of the spring shown in Fig. 3.1. [1] (b) Determine: (i) the spring constant, in N m^-1, of the spring. spring constant = ... N m^-1 [2] (ii) the strain energy (elastic potential energy) in the spring when the extension is 4.0 cm. strain energy = ... J [2] (c) One end of the spring is attached to a fixed point. A cylinder that is submerged in a liquid is now suspended from the other end of the spring, as shown in Fig. 3.2. [Diagram: a spring of extension 4.0 cm hanging from a fixed point, supporting a cylinder fully submerged in liquid in a beaker; cylinder length 5.8 cm, cross-sectional area 1.2 × 10^-3 m^2, weight 6.20 N.] The cylinder has length 5.8 cm, cross-sectional area 1.2 × 10^-3 m^2 and weight 6.20 N. The cylinder is in equilibrium when the extension of the spring is 4.0 cm. (i) Show that the upthrust acting on the cylinder is 0.60 N. [1] (ii) Calculate the difference in pressure between the bottom face and the top face of the cylinder. difference in pressure = ... Pa [2] (iii) Calculate the density of the liquid. density = ... kg m^-3 [2] (d) The liquid in (c) is replaced by another liquid of greater density. State the effect, if any, of this change on: (i) the upthrust acting on the cylinder [1] (ii) the extension of the spring. [1] [Total: 12]
3 A pendulum consists of a solid sphere suspended by a string from a fixed point P, as shown in Fig. 3.1. [Diagram: sphere at lowest position X directly below P with the string vertical, a horizontal arrow labelled momentum 0.72 N s; a dashed position Y up and to the right at height h above X with the string at angle θ to the vertical; the vertical distance from P to the level of X is 0.93 m.] Fig. 3.1 (not to scale) The sphere swings from side to side. At one instant the sphere is at its lowest position X, where it has kinetic energy 0.86 J and momentum 0.72 N s in a horizontal direction. A short time later the sphere is at position Y, where it is momentarily stationary at a maximum vertical height h above position X. The string has a fixed length and negligible weight. Air resistance is also negligible. (a) On Fig. 3.1, draw a solid line to represent the displacement of the centre of the sphere at position Y from position X. [1] (b) Show that the mass of the sphere is 0.30 kg. [3] (c) Calculate height h. h = m [2] (d) The distance between point P and the centre of the sphere is 0.93 m. When the sphere is at position Y, the string is at an angle θ to the vertical. Show that θ is 47°. [1] (e) For the sphere at position Y, calculate the moment of its weight about point P. moment = N m [2] (f) State and explain whether the sphere is in equilibrium when it is stationary at position Y. [1] [Total: 10]
3 A child of weight 330 N is at point X at the top of a slide. The slide is at the edge of a swimming pool, as shown in Fig. 3.1. [Diagram: a curved slide from X at the top, 4.0 m vertically above its lowest point, rising to end point Y which is 1.1 m above the lowest point, next to the water of a swimming pool.] Fig. 3.1 (not to scale) The child moves from rest to the lowest point of the slide that is a vertical distance of 4.0 m below X. The child continues moving towards point Y which is at the end of the slide and a vertical distance of 1.1 m above the lowest point. The kinetic energy of the child at Y is 540 J. (a) Calculate the difference in the gravitational potential energy of the child at points X and Y. difference in gravitational potential energy = J [2] (b) An average frictional force of 52 N acts on the child when moving from X to Y. By considering changes of energy, determine the distance moved by the child from X to Y. distance moved = m [2] (c) The child leaves the slide at point Y with a velocity that is at an angle of 41° to the horizontal. The path of the child through the air is shown in Fig. 3.2. [Diagram: a dashed parabolic path from Y at the end of the slide, velocity arrow at 41° above the horizontal, with Z marked as the highest point, landing in the pool water.] Fig. 3.2 (not to scale) Point Z is the highest point on the path of the child through the air. Assume that air resistance is negligible. Calculate the speed of the child at: (i) point Y speed = m s^-1 [2] (ii) point Z. speed = m s^-1 [2] [Total: 8]
3 (a) Define the moment of a force about a point. [2] (b) Fig. 3.1 shows a type of balance that is used for measuring mass. [Diagram: a horizontal rigid rod pivoted at a point; on the left a pointer at the end of the rod against a mm scale from 0 to 200, the scale being 52.6 cm from the pivot; on the right a pan whose centre is 6.2 cm from the pivot; a spring hangs from a fixed point P and is attached to the rod 1.8 cm from the pivot on the pan side.] Fig. 3.1 (not to scale) A rigid rod is pivoted about a point 6.2 cm from the centre of a pan which is attached to one end. The object being measured is placed on the centre of this pan. A spring, attached to the rod 1.8 cm from the pivot, is attached at its other end to a fixed point P. The spring obeys Hooke's law over the full range of operation of the balance. A pointer, on the other side of the pivot, is set against a millimetre scale which is a distance 52.6 cm from the pivot. When the system is in equilibrium with no mass on the pan, the rod is horizontal and the pointer indicates a reading on the scale of 86 mm. An object of mass 0.472 kg is now placed on the pan. As a result, the pointer moves to indicate a reading of 123 mm on the scale when the system is again in equilibrium. (i) Show that the increase in the length of the spring is approximately 1.3 mm. [2] (ii) Calculate the magnitude of the moment about the pivot of the weight of the object. moment = N m [2] (iii) Use your answer in (b)(ii) to determine the increase in the tension in the spring due to the 0.472 kg mass. increase in tension = N [2] (iv) Use the information in (b)(i) and your answer in (b)(iii) to determine the spring constant k of the spring. Give a unit with your answer. k = unit [2] [Total: 10]
3 (a) A uniform metal bar, initially unstretched, has sides of length w, x and y, as shown in Fig. 3.1. [Diagram: cuboid with sides w (long), x and y (cross-section).] The bar is now stretched by a tensile force F applied to the shaded ends. The changes in the lengths x and y are negligible. The bar now has sides of length x, y and z, as shown in Fig. 3.2. [Diagram: the same bar stretched to length z with force F pulling at each end.] Determine expressions, in terms of some or all of F, w, x, y and z, for: (i) the stress σ applied to the bar by the tensile force. σ = [1] (ii) the strain ε in the bar due to the tensile force. ε = [1] (iii) the Young modulus E of the metal from which the bar is made. E = [2] (b) A copper wire is stretched by a tensile force that gradually increases from 0 to 280 N. The variation with extension of the tensile force is shown in Fig. 3.3. [Graph: force / N (0 to 320) against extension / mm (0 to 12); straight line through the origin up to about 2.2 mm and about 190 N, then curving over to flatten at about 280 N at 12 mm.] (i) State the maximum extension of the wire for which it obeys Hooke's law. extension = mm [1] (ii) Use Fig. 3.3 to determine the strain energy in the wire when the tensile force is 120 N. strain energy = J [3] (iii) Explain why the work done in stretching the wire to an extension of 12 mm is not equal to the energy recovered when the tensile force is removed. [2] [Total: 10]
3 (a) Define power. [1] (b) A car of mass 1700 kg moves in a straight line along a slope that is at an angle θ to the horizontal, as shown in Fig. 3.1. [Diagram: car on a slope from point A to point B, distance 25 m along the slope, angle θ to the horizontal.] Fig. 3.1 (not to scale). The car moves at constant velocity for a distance of 25 m from point A to point B. Air resistance and friction provide a total resistive force of 440 N that opposes the motion of the car. For the movement of the car from A to B: (i) state the change in the kinetic energy. change in kinetic energy = J [1] (ii) calculate the work done against the total resistive force. work done = J [1] (c) The movement of the car in (b) from A to B causes its gravitational potential energy to increase by 4.8 × 10^4 J. Calculate: (i) the increase in vertical height h of the car for its movement from A to B. h = m [2] (ii) angle θ. θ = ° [1] (d) The engine of the car in (b) produces an output power of 1.7 × 10^4 W to move the car along the slope. Calculate the time taken for the car to move from A to B. time = s [2] [Total: 8]
Paper 2: quick facts
Which topics come up most in A Level Physics 9702 Paper 2?
The most-tagged topics in A Level Physics 9702 Paper 2 are Dynamics (65), Work, energy and power (65) and Electricity (53), out of 324 past-paper questions from 2020-2026. These are archive counts, not a prediction, and a question can carry more than one topic.
Are the A Level Physics 9702 Paper 2 questions free?
93 of the 324 A Level Physics 9702 Paper 2 questions are free to practise. The other 231 need a plan for A Level Physics 9702, from $6 a month.
Do the A Level Physics 9702 Paper 2 questions have answers?
Yes. Each A Level Physics 9702 Paper 2 question shows the official mark scheme answer.